2005 Citroen XSARA fuel pressure

Downloaded from www.Manualslib.com manuals search engine 244
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HX - 9HY - 9HZ
Checking and setting the timing (continued).
Turn the engine in the normal direction of rotation until the peg [1]engages in the setting hole.
Peg the flywheel at «b», using tool [1].
Move aside the electrical harness (6).
Remove:
- The engine support (7).
- The screw (8).
- The accessories drive pulley (9).
- The lower timing cover (10).
- The upper timing cover (11).
- The tool [1].
Refit the screw (8).
Rotate the crankshaft to bring the camshaft to its pegging point.
Peg:
- The camshaft at «c», using tool [2]
(oil the pegs).
- The fuel high pressure pump pulley (15)at «f»using a 5 mmdiameter peg.
WARNING: Do not touch or damage the track of the engine speed sensor target (14).
B1BP305C
B1EP1HJD
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 244

Downloaded from www.Manualslib.com manuals search engine 246
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HX - 9HY - 9HZ
Checking and setting the timing (continued).
Refitting.
Fit the timing belt on the crankshaft pinion.
Position the belt on the guide roller, belt well tensioned.
Refit:
- The timing belt protector (13).
- The engine speed sensor (14).
Reposition the timing belt, strip «f»well tensioned, in the following sequence:
- Guide roller (17).
- Camshaft pulley (16).
- Fuel high pressure pump pulley (15).
- Coolant pump pulley (19).
- Tensioner roller (18).
B1EP1HMC
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 246

Downloaded from www.Manualslib.com manuals search engine 256
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ - 9HY
B1EP1E7D
Refitting.
Fit the timing belt on the crankshaft pinion.
Position the belt on the guide roller, belt well tensioned.
Refit:
- The timing belt protector (13).
- The engine speed sensor(14).
Reposition the timing belt, strip «f»well tensioned, in the following sequence:
- Guide roller (16).
- Camshaft pulley (20).
- Fuel high pressure pump pulley (19).
- Coolant pump pulley (17).
- Tensioner roller (18).
XSARA PICASSO
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 256

Downloaded from www.Manualslib.com manuals search engine 268
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: RHY - RHZ
Reposition the timimg belt, belt at «a»well tensioned, in the following order:
- Fuel high pressure pump pulley (21).
- Guide roller (15).
- Crankshaft pinion (19).
- Coolant pump pinion (16).
- Tensioner roller (18).
Position tool [1]on the belt at «a».
Remove tools [4]and [9].
Turn the tensioner roller (18)anti-clockwise, using tool [2], to attain an overtension of:
98 ± 2 SEEMunits.
Tighten screw (17)of the tensioner roller to 2,5 ± 0,2 m.da N.
Lock the flywheel by means of tool [6].
Tighten the accessories drive pulley screw (8)to 7 ± 0,7 m.da N.
Remove tools [1], [3], [5]and [6].
Rotate the crankshaft eight times in the normal direction of rotation.
Peg:
- The crankshaft, using tool [3].
- The camshaft drive pulley, using tool [5].
B1EP1ABD
B1EP1ACC
XSARA - XSARA PICASSO
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 268

Downloaded from www.Manualslib.com manuals search engine 271
ENGINE
CHECKING THE VALVE TIMING
Engine: RHR
Tools.
[1] Kit of plugs: (-).0188.T
[2] Double flywheel setting peg: (-).0188.X Toolkit 0188-T
[3]Camshaft setting peg: (-).0188.M
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure Diesel
injection (HDi) engine versions.
Remove the engine cover and the battery.
Disconnect the negative terminal of the battery.
Raise and support the front of the vehicle.
Remove the under-engine sound-deadening and the front RH splash-shield.
Uncouple, plug and move aside, using tool [1], the fuel supply and fuel return pipes..
Suspend the engine, using a workshop hoist.
Remove the engine support bracket and the engine support.
Move aside the electrical harness (1).
Remove:
- The camshaft position sensor.
- The inlet cylinder head cover (2).
- The upper timing cover screws.
- The upper timing cover (3).
B1EP1GFC
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 271

Downloaded from www.Manualslib.com manuals search engine 283
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Tools.
[1] Ø 10 mmlow pressure connector: 4215-T
[2]Pressure gauge for testing boost pressure: 4073-T.A Toolkit 4073-T
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel injection
engines.
Link tools [1]and [2] in series between the fuel high pressure pump and the fuel filter.
ESSENTIAL: Check that the tool [2] is clean.
Check the negative pressure according to the table below:
Vacuum Observations
10 ± 5 cmHgEngine driven by the starter motor
20 ± 5 cmHgEngine running under full load
60 ± 5 cmHgSupply circuit obstructed
(full tank strainer, piping, fuel filter)
B1BP2WHC
Engines: 8HX - 8HZ
XSARA
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 283

Downloaded from www.Manualslib.com manuals search engine 284
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Tools.
[1] Ø 10 mmlow pressure connector: 4215-T
[2]Pressure gauge for testing boost pressure: 4073-T.A Toolkit 4073-T
IMPERATIV: Respect the safety and cleanliness specific to high pressure diesel injection
engines.
Remove the air filter duct.
Link tool [1]in series, downstream of the injectors, between the fuel high pressure pump and the
fuel filter at «a»and «b».
WARNING: Any checking of pressure downstream of the fuel filter is prohibited.
Switch on the ignition.
Check the pressure :
Vacuum measured by the pressure gauge [2]:
Vacuum Observations
10 ± 0,5 cmHgEngine driven by the starter motor.
20 ± 0,5 cmHgEngine running under full load
60 ± 0,5 cmHgSupply circuit obstructed
(full tank strainer, piping, fuel filter)
B1CP0GFD
Engines: 9HX - 9HY - 9HZ
C4
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 284

Downloaded from www.Manualslib.com manuals search engine 285
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Tools.
[1] Ø 10 mm low pressure connector: 4215-T
[2] Pressure gauge for testing boost pressure: 4073-T.A Toolkit 4073-T
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel injection
engines.
Remove the air filter duct.
Link tool [1]in series, downstream of the injectors, between the fuel high pressure pump and the
fuel filter at «a»and «b».
WARNING: Any checking of pressure downstream of the fuel filter is prohibited.
Switch on the ignition.
ESSENTIAL: Check that the tool [2] is clean.
Check the negative pressure according to the table below:
Vacuum Observations
10 ± 05 cmhgEngine driven by the starter motor
20 ± 20 cmhgEngine running under full load
60 ± 05 cmhgSupply circuit obstructed
(full tank strainer, piping, fuel filter
B1BP2PHC
Engines: 9HZ - 9HY
XSARA PICASSO
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 285