2005 Citroen XSARA PICASSO rear

Downloaded from www.Manualslib.com manuals search engine CLUTCH - GEARBOX - TRANSMISSION (continued)
Gearbox specifications312 - 314
Clutch specifications315 - 316
Checking and adjusting the hydraulic
clutch control317 - 318
Tightening torques: manual gearbox
319 - 330
Manual gearbox controls
331 - 343
Recommendations - precautions:
automatic gearbox344 - 346
Tightening torques: manual gearbox
347 - 349
Automatic gearbox controls
350 - 359
Driveshafts360
AXLES - SUSPENSION - STEERING
Axle geometry: C4361 - 364
Tightening torques: front axle365 - 366
Tightening torques: rear axle367
Tightening torques: power steering368 - 369
Setting the steering rack mid-point370
Checking the power steering pressure371 - 374
Axle geometry: Xsara375 - 379Adjusting the handbrake 426
Filling, bleeding the brakes427
AIR CONDITIONING
R134.a: quantities428
Checking the compressor lubricant429 - 430
Pollen filter: all types431 - 433
Filtering and drying cartridge434 - 436
Checking the efficiency of the circuit437 - 446
C4447 - 451
Xsara452
Xsara picasso453 - 456
CONTENTS
Tightening torques: front axle380
Tightening torques: rear axle382
Tightening torques: steering 383 - 384
Tightening torques: power steering385 - 387
Axle geometry: Xsara Picasso388 - 392
Tightening torques: front axle393
Tightening torques: rear axle394
Tightening torques: power steering395 - 397
BRAKES
Brake specifications: C4398 - 399
Tightening torques: Brakes401 - 403
Adjusting the handbrake 405
Filling, bleeding the brakes406 - 410
Brake specifications: Xsara411
Tightening torques 414
Brake specifications415 - 418
Adjusting the handbrake 419
Filling, bleeding the brakes420
Brake specifications: Xsara Picasso421 - 422
Brake specifications423 - 424
Aircon circuit
Angl-t2-Index-2005 9/01/06 10:05 Page IV

Downloaded from www.Manualslib.com manuals search engine 35
GENERAL
LUBRICANTS - TOTAL recommended oils
GEARBOX OILS
TOTAL TRANSMISSION BV
Norms S.A.E: 75W80
Part No.: 9730 A2
TOTAL FLUIDE ATX
T O TA L F L U I D E AT 4 2
Special oil distributed by
CITROËN
Part No.: 9730 A6
Special oil distributed by
CITROËN
Part No.: 9736 22 Manual and piloted manual
gearboxes
MB3 automatic gearbox
4HP20 and AL4 autoactive
automatic gearboxes
All countries
Special oil distributed by
CITROËN
Part No.: 9980 D4
TOTAL TRANSMISSION X4
Part No.: 9730 A7 AM6 autoactive automatic gearbox
Transfer box and rear axle
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 35

Downloaded from www.Manualslib.com manuals search engine 109
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Injection circuit
44 Diesel fuel high pressure pump rear support 2 ± 0,5
Union on diesel fuel high pressure pump
45Pre-tightening2 ± 0,5
Tightening2,5 ± 0,3
46 Fuel high pressure common injection rail on engine block 2,2 ± 0,3
Unions on fuel high pressure common injection rail
47Pre-tightening2 ± 0,5
Tightening2,5 ± 0,3
48 Fuel filter support 0,7 ± 0,1
Engine: 9HX
B1HP22SD
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 109

Downloaded from www.Manualslib.com manuals search engine 121
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Injection circuit
44 Diesel fuel high pressure pump rear support 2 ± 0,5
Union on diesel fuel high pressure pump
45Pre-tightening2 ± 0,5
Tightening2,5 ± 0,3
46 Fuel high pressure common injection rail on engine block 2,2 ± 0,3
Unions on fuel high pressure common injection rail
47Pre-tightening2 ± 0,5
Tightening2,5 ± 0,3
48 Fuel filter support 0,7 ± 0,1
Engines: 9HY - 9HZ
B1HP22SD
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 121

Downloaded from www.Manualslib.com manuals search engine 178
ENGINEXSARA - XSARA PICASSO
AUXILIARY EQUIPMENT DRIVE BELT
Engines: RHY - RHZ
With air conditioning
B1BP1YLD
Tools.
[1]Belt tension adjusting square: (-).0188 J2
[2] Ø 4 mmpeg: (-).0188.Q1
[3] Ø 2 mmpeg: (-).0188.Q2
[4]Dynamic tensioner compression lever: (-).0188.Z
Removal.
Re-use of belt.
WARNING: Mark the direction the belt was fitted in case of re-use of the same belt.
Compress the tensioner roller (7)by moving it at «c»
(in anti-clockwise direction), tool [4].
Hold the tensioner roller (7) compressed and remove the belt.
No re-use of belt.
Compress the tensioner roller (7)by moving it at «c»
(in anti-clockwise direction), tool [4].
Peg using tool [2], at «d».
Loosen the screw (6).
Bring the eccentric roller (5)towards the rear.
Tighten the screw (6)by hand.
Remove the belt.
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 178

Downloaded from www.Manualslib.com manuals search engine 322
CLUTCH
GEARBOX
TRANSMISSION
MA/5 GEARBOX SPECIFICATIONS
Engines: KFW - NFU
Tightening torques (m.daN).
(23) Clutch bearing guide (3 fixing screws): 0,6 ± 0,15
(24)Intermediate plate
(11 fixing screws): 5 ± 0,5
(25)Rear cover
(3 fixing screws): 2,2 ± 0,2
(26)Bearing retaining clip
(4 fixing screws): 1,8 ± 0,2
(27)Secondary shaft nut
(1 nut): 14 ± 1
(28)Gearbox casing
(15 fixing screws): 1,8 ± 0,2
B2CP167P
XSARA
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 322

Downloaded from www.Manualslib.com manuals search engine 327
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: BE4/5 GEARBOX
Engines: 6FZ - RFN - WJY - 8HX - 8HZ - 9HY - 9HZ - RHY - RHZ
T
ightening torques (m.daN).
(23)Clutch bearing guide (3 screws): 1,25 ± 0,2
(24)Clutch housing
(13 screws): 1,3 ± 0,2
(25)Primary shaft nut
(1 screw): 7,25 ± 0,5
(26)Secondary shaft nut
(1 screw): 6,5 ± 0,5
(27)Yoke retaining screw
(2 screws): 1,5 ± 0,2
(28)Differential gearwheel screw
(2 screws): 6,5 ± 0,5
Reverse gear switch (1 screw): 2,5 ± 0,3
(29)Differential housing
(4 screws): 5 ± 0,5
(30)Breather pipe: 1,7 ± 0,2
(31)Rear housing cover screws
(7 screws): 1,25 ± 0,2
(32)Top-up plug
(1 screw): 2,2 ± 0,2
(33) Differential housing screws
(4 screws): 1,25 ± 0,2
(34)Drain plug
(1 screw): 3,5 ± 0,3
B2CP3BRD
XSARA - XSARA PICASSO
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 327

Downloaded from www.Manualslib.com manuals search engine 361
AXLES
SUSPENSION
STEERING
AXLE GEOMETRY
Conditions for checking and adjusting
Vehicle heights at reference height
Rear height Front height
L2 L1
Tools : [1] Gauge for measuring the the wheel radius, 4 bolts: 4300-T.
Tyres inflated to correct pressures. Vehicle at reference height.
Steering rack locked at mid point
(see corresponding operation).
H1 = R1 - L1
H1 = Measurement between the measuring zone underneath the front
subframe and the ground.
R1 = Front wheel radius under load.
L1 =Distance between the wheel axis and the measuring zone underneath
the front subframe.H2 = R2 + L2
H2 = Measurement between the measuring zone underneath the rear sill
and the ground.
R2 =Rear wheel radius under load.
L2 =Distance between the wheel axis and the measuring zone underneath
the rear sill.
E1AP0F3D
C4
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 361