2005 Citroen XSARA PICASSO lubrication

Downloaded from www.Manualslib.com manuals search engine 10
GENERAL
Draining methods
Oil capacities are defined according to the following methods
CAPACITIES (in litres)
Draining of the engine lubrication system by GRAVITY
Place the vehicle on horizontal ground
(in the high position if
hydropneumatic suspension)
.
The engine should be hot
(oil temperature 80°C).
Drain the sump by gravity.
Remove the oil filter cartridge
(time for draining and drip-drip = 15
minutes approx.)
.
Refit the cap with a new seal.
Refit a new oil filter cartridge.
Refill the engine with oil
(see table for oil capacity).
Start the engine to fill the oil filter cartridge.
Stop the engine
(allow to stabilise for 5 minutes).Draining of the engine lubrication system by SUCTION
Place the vehicle on horizontal ground
(in the high position if
hydropneumatic suspension).
The engine should be hot (oil temperature 80°C).
Remove the oil by suction through the dipstick tube.
Remove the oil filter cartridge.
Maintain the suction of oil in the sump
(15 minutes approx.).
Refit a new oil filter cartridge.
Refill the engine with oil
(see table for oil capacity).
Start the engine to fill the oil filter cartridge.
Stop the engine
(allow to stabilise for 5 minutes).
WARNING: Remove the suction container before starting the engine.
ESSENTIAL: Systematically check the oil level using the oil dipstick.
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 10

Downloaded from www.Manualslib.com manuals search engine 51
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Lubrication
26 Oil gauge screw 0,7 ± 0,1
27 Electric oil gauge fixng screw 3,2 ± 0,5
28 Oil filter support screw 1 ± 0,1
29 Strainer fixing screw 1 ± 0,1
30 Oil pressure switch 2 ± 0,2
31 Oil sump screw 0,8 ± 0,2
32 Drain plug 3 ± 0,5
33 Oil pump screw 0,9 ± 0,1
Engine: KFU
B1BP369P
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 51

Downloaded from www.Manualslib.com manuals search engine 55
ENGINE
SPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Cylinder head1 Inlet air pressure sensor 0,8 ± 0,12 Motorised butterfly housing fixing screws 0,7 ± 0,13 Inlet manifold nuts 0,8 ± 0,24 Valve cover screws (*) 0,9 ± 0,15 Coolant outlet housing screw 0,8 ± 0,26 Thermostat fixing screw 0,8 ± 0,27 Oxygen sensor 4,7 ± 0,7
Catalytic converter fixing nuts (*)
8Pre-tightening1,8 ± 0,3
Tightening4 ± 0,4
Check the tightening4 ± 0,49 Exhaust manifold nuts 2,3 ± 0,510 Exhaust manifold fixing stud 0,8 ± 0,111 Lubrication plug 1,5 ± 0,2
Cylinder head bolts (*)
12Tightening2 ± 0,2
Angular tightening260° ± 5°13 Camshaft bearing cap screws (*) 0,9 ± 0,114 Inlet manifold fixing stud 0,8 ± 0,115 Engine coolant temperature sensor (CMM) 1,7 ± 0,116 Engine coolant temperature sensor (instrument panel) 1,7 ± 0,1
17 Sparking plugs 3 ± 0,1
Engine: NFU
B1BP362P
(*) = IMPERATIVE: Respect the tightening sequence (see following page).
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 55

Downloaded from www.Manualslib.com manuals search engine 58
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Lubrication
29 Strainer fixing 0,8 ± 0,2
30 Oil gauge screw 0,8 ± 0,1
31 Piston skirt spray jet 1,5 ± 0,2
32 Drain plug 3 ± 0,5
33 Oil sump screw 0,8 ± 0,1
34 Oil pressure switch 2 ± 0,2
35 Oil circuit plugs 2,5 ± 0,5
36 Oil filter support screw 0,8 ± 0,2
37 Oil level sensor 0,8 ± 0,2
38 Oil pump screw 0,9 ± 0,1
Engine: NFU
B1BP363P
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 58

Downloaded from www.Manualslib.com manuals search engine 68
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Lubrication
26 Oil gauge screw 1 ± 0,2
27 Oil filter support screw 0,8 ± 0,1
28 Anti-emulsion plate fixing screw 1,9 ± 0,3
29 Oil level sensor fixing screw 1 ± 0,2
30 Drain plug 3,4 ± 0,3
31 Oil sump screw 0,8 ± 0,1
32 Oil pressure switch 2 ± 0,2
33 Oil strainer fixing nuts 0,8 ± 0,1
34 Oil strainer stud 0,6 ± 0,1
Coolant pump screw
35Pre-tightening0,7
Tightening1 ± 0,1
Engine: RFJ
B1BP35NP
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 68

Downloaded from www.Manualslib.com manuals search engine 74
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Lubrication circuit
Oil pump closing plate 0,8 ± 0,1
Oil pump
Pre-tightening0,7 ± 0,1
Tightening0,9 ± 0,1
Injection circuit
Common injection rail fixing screws 0,9 ± 0,1
Cooling circuit
Coolant pump
Pre-tightening
(sequence 1,2,3,4)0,8 ± 0,1
Tightening(sequence 1,2,3,4)1,4 ± 0,1
Coolant inlet housing 0,9 ± 0,1
Engine: RFN
B1GP08WC
XSARA - XSARA PICASSO
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 74

Downloaded from www.Manualslib.com manuals search engine 82
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Lubrication
27 Oil gauge screw 1 ± 0,2
28 Oil level sensor fixing screw 1 ± 0,2
29 Drain plug 3,4 ± 0,3
30 Oil sump screw 0,8 ± 0,1
31 Oil pressure switch 2 ± 0,2
32 Oil strainer fixing nuts 1,1 ± 0,1
33 Oil strainer stud 0,6 ± 0,1
Oil pump screw
34Pre-tightening0,7
Tightening1 ± 0,1
35 Oil filter support screw 0,8 ± 0,2
36 Anti-emulsion plate fixing screw 1,9 ± 0,3
Engine: RFN
B1BP34NP
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 82

Downloaded from www.Manualslib.com manuals search engine 92
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Lubrication
26 Oil gauge screw 1 ± 0,2
27 Oil level sensor fixing screw 1 ± 0,2
28 Drain plug 3,4 ± 0,3
29 Oil sump screw 0,8 ± 0,1
30 Oil pressure switch 2 ± 0,2
31 Oil strainer stud 0,6 ± 0,1
Oil pump screw
32Pre-tightening0,7
Tightening1 ± 0,1
33 Oil strainer fixing nuts 1,1 ± 0,1
34 Oil filter support screw 0,8 ± 0,2
35 Anti-emulsion plate fixing screw 1,9 ± 0,3
Engine: RFK
B1BP35RP
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 92