2005 Citroen C4 clutch slave

Downloaded from www.Manualslib.com manuals search engine 315
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS
Engines: KFU - NFU - RFN - RFJ - RFK - 9HX - 9HY - 9HZ - RHR
NOTE:All the clutches are «push»type with hydraulic control.
NOTE:The DV6TED4and DW10BTED4engines are equipped with a double damping flywheel (DVA).
Description.
The declutch control has a declutch fork with a ball-joint on the axis.
(1)The ball-joint is screwed into the clutch casing
(2) Declutch fork
(3)Clutch casing
(4)Bearing
(5) Clutch plate
The clutch control slave cylinder(7)is fixed by two screws (6) into the exterior of the clutch casing.
B2BP047C
B2CP3FAC
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 315

Downloaded from www.Manualslib.com manuals search engine 316
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS
Engines: KFW - NFU - NFV - 6FZ - RFN - 8HX - 8HZ - 9HY - 9HZ - WJY - RHY - RHZ
NOTE:All the clutches are «push»type with hydraulic control.
Description.
The declutch control has a declutch fork mounted on a ball-joint.
(1)The ball-joint is screwed into the clutch casing
(2)Declutch fork
(3)Clutch casing
(4)Bearing
(5)Clutch plate
The clutch control slave cylinder (7)is fixed by two screws (6)onto the exterior of the clutch casing.
T
ightening torques (m.daN).
Fixing of clutch plate/engine flywheel: 2 ± 0,2.
Fixing of clutch control slave cylinder / clutch housing: 2 ± 0,25.
Fixing of engine flywheel/crankshaft
Pre-tightening: 1,75 ± 0,2.
Angular tightening: 75° ± 5°.
Checking torque: 6,3 ± 2,2.
B2BP047CB2BP05SC
XSARA - XSARA PICASSO
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 316

Downloaded from www.Manualslib.com manuals search engine 317
CLUTCH
GEARBOX
TRANSMISSION
HYDRAULIC CLUTCH CONTROL: CHECKS AND ADJUSTMENTS
B2BP04XC
IMPERATIVE: Use only new brake brake fluid that is not emulsified, avoid any
ingress of impurities into the hydraulic circuit.
IMPERATIVE: Do not use automatic bleeding equipment
(risk of the brake fluid
emulsifying in the hydraulic circuit).
Couple a transparent tube (5)on the bleed screw, at «c».
Submerge the end of the tube (5)in the recipient containing the brake fluid, located
below the level of the clutch slave cylinder.
Use the transparent tube (5) to act as a siphon, at «b».
WARNING: the end of the tube (5) must be submerged in the brake fluid.
Open the bleed screw at «c».
XSARA PICASSO
Bleeding the hydraulic clutch control
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 317

Downloaded from www.Manualslib.com manuals search engine 320
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: MA/5 GEARBOX
Engines: KFU - NFU
Tightening torques (m.daN).
(6)Clutch bearing guide screw: 1 ± 0,1
(7)Bearing retaining clip screw: 1,8 ± 0,2
Intermediate plate fixing: 5 ± 0,5
Hydraulic clutch slave cylinder fixing: 3 ± 0,3
B2CP3ZJD
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 320