2005 Citroen C4 FRONT

Downloaded from www.Manualslib.com manuals search engine CLUTCH - GEARBOX - TRANSMISSION (continued)
Gearbox specifications312 - 314
Clutch specifications315 - 316
Checking and adjusting the hydraulic
clutch control317 - 318
Tightening torques: manual gearbox
319 - 330
Manual gearbox controls
331 - 343
Recommendations - precautions:
automatic gearbox344 - 346
Tightening torques: manual gearbox
347 - 349
Automatic gearbox controls
350 - 359
Driveshafts360
AXLES - SUSPENSION - STEERING
Axle geometry: C4361 - 364
Tightening torques: front axle365 - 366
Tightening torques: rear axle367
Tightening torques: power steering368 - 369
Setting the steering rack mid-point370
Checking the power steering pressure371 - 374
Axle geometry: Xsara375 - 379Adjusting the handbrake 426
Filling, bleeding the brakes427
AIR CONDITIONING
R134.a: quantities428
Checking the compressor lubricant429 - 430
Pollen filter: all types431 - 433
Filtering and drying cartridge434 - 436
Checking the efficiency of the circuit437 - 446
C4447 - 451
Xsara452
Xsara picasso453 - 456
CONTENTS
Tightening torques: front axle380
Tightening torques: rear axle382
Tightening torques: steering 383 - 384
Tightening torques: power steering385 - 387
Axle geometry: Xsara Picasso388 - 392
Tightening torques: front axle393
Tightening torques: rear axle394
Tightening torques: power steering395 - 397
BRAKES
Brake specifications: C4398 - 399
Tightening torques: Brakes401 - 403
Adjusting the handbrake 405
Filling, bleeding the brakes406 - 410
Brake specifications: Xsara411
Tightening torques 414
Brake specifications415 - 418
Adjusting the handbrake 419
Filling, bleeding the brakes420
Brake specifications: Xsara Picasso421 - 422
Brake specifications423 - 424
Aircon circuit
Angl-t2-Index-2005 9/01/06 10:05 Page IV

Downloaded from www.Manualslib.com manuals search engine GENERAL
1
IDENTIFICATION OF THE VEHICLE
E1AP0EWD
A- Manufacturer's name plate
A1 -Front RH chassis member = All versions except
CITROËN C4Coupé EW10J4S
(right hand drive).A2 -LH centre pillar = CITROËN C4 coupé EW10J4S(right hand drive).
B - Cold stamp
(cold stamp engraved on the bodywork).
C - AS/RP No. and RP paint code
(on the front pillar on driver's side).
D - Tyre pressures and tyre type
(on the front pillar on driver's side).
E - Serial number on bodywork.
F - Gearbox ident. reference - Factory serial no.
G - Engine legislation type - Factory serial no.
GENERAL
C4
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 1

Downloaded from www.Manualslib.com manuals search engine GENERAL
3
IDENTIFICATION OF THE VEHICLE
E1AP08WD
A- Manufacturer's name plate (estate).
B -Chassis stamp, cold stamp.
C -Manufacturer's name plate (saloon).
D -Label:
(label affixed to the front pillar on driver's side)
- Tyre pressures.
- RP organisation no.
- Paint code.
E - Serial number (visible through the windscreen).
F -Engine legislation type - Factory serial no.
G - Gearbox ident. reference - Factory serial no.
XSARA
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 3

Downloaded from www.Manualslib.com manuals search engine GENERALGENERAL
5
IDENTIFICATION OF THE VEHICLEXSARA PICASSO
E1AP088D
A- Chassis stamp
(cold stamp on bodywork).
B -Chassis no. reminder
(label located at bottom of windscreen right hand side).
C -Manufacturer's data plate
(located at bottom of RH central pillar).
D -Label:
(located on front LH door inner panel)
- Tyre pressures.
- Tyre identification.
- Spare wheel identification.
E -Label:
(located on fuse box cover)
- Factory code.
- A-S / RP N°.
- Paint code.
F -Gearbox identification ref.
G -Engine legislation type - Factory serial number.
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 5

Downloaded from www.Manualslib.com manuals search engine 108
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Injection circuit
Union on injector
39Pre-tightening2 ± 0,5
Tightening2,5 ± 0,3
Injector fixing flange but
40Pre-tightening0,5 ± 0,5
Angular tightening65°±5°
41 Diesel injection pump on support 2,2 ± 0,3
42 Diesel injection pump pulley 5 ± 0,5
43 Diesel fuel high pressure pump front support 2 ± 0,5
Engine: 9HX
B1HP22SD
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 108

Downloaded from www.Manualslib.com manuals search engine 120
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Injection circuit
Union on injector
39Pre-tightening2 ± 0,5
Tightening2,5 ± 0,3
Injector fixing flange but
40Pre-tightening0,5 ± 0,5
Angular tightening65°±5°
41 Diesel injection pump on support 2,2 ± 0,3
42 Diesel injection pump pulley 5 ± 0,5
43 Diesel fuel high pressure pump front support 2 ± 0,5
Engines: 9HY - 9HZ
B1HP22SD
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 120

Downloaded from www.Manualslib.com manuals search engine 142
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Cylinder block
13 Front closing plate screw
Flywheel screws
14Pre-tightening1,5
Tightening4,7 ± 0,4
Accessories drive pulley screw
15Pre-tightening7 ± 0,25
Angular tightening60°±5°
Engine: RHR
B1CP0GNP
C4
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 142

Downloaded from www.Manualslib.com manuals search engine 156
ENGINE
B1BP2LSC
B1BP2LTC
AUXILIARY EQUIPMENT DRIVE BELT
Engines: KFU - NFU
Tools.
[1]Pliers for removing plastic pegs: 7504 -T
[2]Belt tension measuring instrument (SEEM) : 4122 -T
[3]Compression lever for dynamic tensioner: (-).0194.D
[4] Peg for dynamic tensioner roller of Ø 4 mm : (-) 0194.F
WARNING: (With or without air conditioning)
The auxiliaries drive belt cannot be re-used
with a manual tensioner roller.
The auxiliaries drive belt can be re-usedwith a dynamic tensioner roller.
Removing.
Raise and support the vehicle, front wheels hanging.
Disconnect the battery.
Remove the front RH wheel and the front RH splash-shield, using tool [1].
V
ehicle without air conditioning.Slacken bolts (2), screw (3)and the tensioning screw (1).
Push back the alternator towards the engine.
Remove the auxiliary equipment drive belt.
Refitting.
Refit the new auxiliary equipment drive belt.
Respect the following sequence: Crankshaft pinion, alternator pulley.
Position tool [2]on the belt.
Tighten the screw (1)to tension the belt to: 120 ± 4 SEEM units.
Tighten screw (3), bolts (2).
Remove tool [2].
Complete the refitting.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 156