2005 Citroen C4 remove

Downloaded from www.Manualslib.com manuals search engine 191
ENGINE
191
CHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Setting the timing (continued).
Rotate the engine by means of the crankshaft screw
(clockwise), to bring it to the pegging position.
Peg the flywheel, using tool [1].
Position the tools [2]and [3].
Remove the engine support assembly (9), the fixing
screw (8)and the lower cover (7).
Slacken the nut (11).
Fully detension the belt by moving the tensioner
roller (10).
Remove the timing belt.
IMPERATIVE: Check that the tensioner roller
turns freely
(no tight spot).
Refitting.
Position the
(new)timing belt, in the following
sequence:
- The inlet camshaft pulley, the exhaust camshaft
pulley, the guide roller, the crankshaft pulley, position
the tool [4], the coolant pump pulley, the dynamic
tensioner roller.
Remove the tools [1], [2], [3]and [4].
B1BP2MBC
B1BP2ZMC
B1CP0GLD
B1CP0GMD
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 191

Downloaded from www.Manualslib.com manuals search engine 192
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Overtension on the belt.
Position «a»: Tensioner roller in detensionedposition.
Position «b»: Tensioner roller in normalposition.
Position «c»: Tensioner roller in overtensionposition.
Turn the tensioner roller (10), using an allen spanner at «e».
Place the index «d»in position «c», hold the belt to the maximum of the interval indicated.
Tighten the tensioner roller fixing nut to 2,1 ± 0,2 m.daN.
Rotate the crankshaft four turns
(normal direction of rotation).
IMPERATIVE: Never turn it backwards.
Check the timing setting by refitting the pegs [1], [2] and [3].
Remove the pegs [1], [2]and [3].
Adjusting the fitting tension of the timing belt.
Slacken the nut, holding the position of the tensioner roller, using an allen spanner at «e».
Bring the index «d»to its adjustment position at «b».
WARNING: The index «d» should not go past the notch «b». If it does, repeat the operation
to tension the timing belt.
Maintain the roller (10)in this position, using an allen spanner.
Tighten the tensioner roller fixing nut to 2,1 ± 0,2 m.daN.
IMPERATIVE: The tensioner roller should not turn during the tightening of its fixing. If it
does, repeat the operation to tension the timing belt.
Complete the refitting.
B1EP1DTC
B1EP1DUC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 192

Downloaded from www.Manualslib.com manuals search engine 194
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Setting the valve timing.
Loosen the screw (2), remove the belt.
Loosen the six pulley screws (1)on the hubs
(there should be a slight amount of friction between the screws and
the pinions).
Check that the rollers (2)and (3) rotate freely.
NOTE: The belt bears three identification marks (a), (b)and (c), facing its own teeth (1), (52)and (72)respectively
(identification marks = white paint lines on the back of the belt facing the corresponding teeth).
Refit the belt.
Line up mark (A)on the belt with groove (D)of the pinion (4).
Hold the belt against the pinion (4).
B1EP11EC
B1EP11DC
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 194

Downloaded from www.Manualslib.com manuals search engine 196
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Setting the valve timing.
Remove the tools [1], [2], [3]and [4].
Rotate the engine by four turnsin the normal direction
(do not turn backwards).
Peg the flywheel [2].
Loosen the six screws (5), while ensuring there is still a slight amount of friction with the pulley.
Peg the camshaft hubs using pegs [3]and [4].
WARNING: In certain cases, it may be necessary to slightly turn the camshaft using the hub fixing screw.
Fit the tool [1].
Loosen the tensioner roller screw (2).
Rotate the roller (2)
(using tool [5])in an anti-clockwise direction to obtain: 37 SEEMunits.
Tighten the tensioner roller screw (2)to 2 m.daN.
Tighten the six pulley screws (1)to 1 m.daN.
Remove the tools.
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 196

Downloaded from www.Manualslib.com manuals search engine 197
ENGINE
CHECKING THE VALVE TIMING
Engine: NFU
Tools.
[1]Flywheel setting peg: 4507-T.A Toolkit 4507-T
[2a]Camshaft setting peg: 4533-TA.C1
[3b]Camshaft setting peg: 4533-TA.C2
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking.
Disconnect the negative terminal of the battery.
Remove:
- The oil filter (1).
- Suspend the engine.
Remove:
- The engine support (2)and the upper timing cover (3).
B1BP2M7C
B1BP381C
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 197

Downloaded from www.Manualslib.com manuals search engine ENGINE
198
CHECKING THE VALVE TIMING
Engine: NFU
Remove the sparking plugs, to facilitate rotation of the crankshaft.
Rotate the engine by means of the crankshaft pinion screw
(clockwise)to bring it to the pegging
position.
Fit the tools [2a]and [2b].
Peg the flywheel, using tool [1].
NOTE:If the setting proves impossible, restart the timing setting operation.
Remove the tools [1], [2a]and [2b].
Complete the refitting.
IMPERATIVE: Carry out the operations that are necessary following a reconnection of the
battery
(see corresponding operation).
B1EP170C
B1BP2MBC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 198

Downloaded from www.Manualslib.com manuals search engine 199
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Tools.
[1]Flywheel setting peg: 4507-T.A Toolkit 4507-T
[2a]Camshaft setting peg: 4533-TA.C1
[2b]Camshaft setting peg: 4533-TA.C2
[3]Belt retaining pin: 4533-T.AD
[4]Dynamic tensioner roller pin: 4200-T.H
IMPERATIVE: Respect the safety and cleanliness requirements.
Removing.
Raise and support the vehicle, front wheels hanging
Disconnect the battery.
Remove:
- The auxiliaries drive belt (4)
(see corresponding operation).
- The crankshaft pulley (3).
- The oil filter.
Suspend the engine, using a workshop hoist.
Remove the timing cover, the engine support (1), the intermediate support and the timing cover (2).
B1BP382C
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 199

Downloaded from www.Manualslib.com manuals search engine 200
ENGINE
200
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Peg the flywheel, using tool [1].
Position the tools [2a]and [2b].
Slacken the tensioner roller.
Turn the dynamic tensioner roller so as to be able
to position the tool[4], with the aid of an Allen key
placed at «a».
Turn the tensioner roller towards the right to bring
it to the index «c»in position «b».
Peg the tensioner roller in this position in order to
slacken the timing belt to the maximum.
IMPERATIVE: Never make the dynamic tensioner
roller turn by a complete rotation.
Remove the timing belt (8).
Check that the rollers and the pump pulley turn
freely
(no tight spot).
B1BP2MBC
B1EP170C
B1EP18PC
B1EP18QC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 200