2005 Citroen C4 c4 picasso

Downloaded from www.Manualslib.com manuals search engine 186
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: KFW - NFV
Refitting the timing belt.
NOTE :Check that the pegs [1]and [2]are in place.
WARNING: Respect the direction of fitting of the belt: The arrows "a" indicate the direction of rotation of
the crankshaft.
Position:
-The timing belt, belt "b"well-tensioned in the following order: Crankshaft pinion, camshaft pulley, coolant pump
pulley, tensioner roller.
- Tool [5]
(respect the direction of fitting relative to the valve timing).
- Put the tensioner roller in contact with the belt.
- Tighten the nut (2).
Pre-tensioning the belt.
Place tool [4] on the tensioned part "b"of the belt.
Slacken the screw (2).
Turn the roller (3)in the anti-clockwise direction using the drive square, to obtain a value of: 44 SEEMunits.
Tighten the nut (2) to 2 m.daN.
Remove tools [1], [2] and [4].
Rotate the crankshaft 4 turnsin the normal direction of rotation.
IMPERATIVE: Never turn the crankshaft backwards.
B1EP06AC
B1EP069C
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 186

Downloaded from www.Manualslib.com manuals search engine 187
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: KFW - NFV
Pre-tensioning the timing belt (continued).
Make sure of the timing setting by refitting the pegs [1]and [2].
Remove the valve cover.
Position the tool [5]
(respect the direction of fitting relative to the valve timing).
Adjusting the belt tension.
Place tool [4]on the tensioned part of the belt.
Slacken the nut (2).
Detension the belt, but too much.
Tension the timing belt to obtain a value of: 31 ± 2 SEEMunits.
Tighten the nut (2)to 2 m.daN.
Remove tools [1], [2], [4] and [5].
Checking the belt tension.
Rotate the crankshaft 2 turnsin the normal direction of rotation.
Check that it is still possible to peg the following components.
Flywheel.
Camshaft.
IMPERATIVE: Repeat the belt tensioning operation if the pegging is not possible.
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 187

Downloaded from www.Manualslib.com manuals search engine 217
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Tools.
[1]Camshaft setting peg: (-) 0189.A
[2] Crankshaft setting peg: (-).0189.R
[3]Timing belt retaining pin: (-).0189.K
[4]Adaptor for angular tightening: 4069-T
[5]Tool for moving and locking the tensioner roller: (-).0189.S
[5a] : (-).0189.S1
[5b] : (-).0189 S2
Pliers for removing plastic pins: 7504-T
Checking the setting of the timing.
Removing.
Disconnect the battery negative terminal
(see corresponding operation).
Raise and support the vehicle, front wheels hanging.
Remove:
- The front RH wheel.
- The plastic pins (1).
- The splash-shield (2).
- The upper timing cover.
C4AP12TC
XSARA - XSARA PICASSO
Engines: 6FZ - RFN
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 217

Downloaded from www.Manualslib.com manuals search engine 218
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ - RFN
Checking the setting of the timing (continued).
A:Pegging on the manualgearbox.
B:Pegging on the automaticgearbox.
Turn the engine by means of the crankshaft pinion screw, to bring it to the pegging position.
Peg the crankshaft, using tool [2].
Peg the camshaft pulleys, using tool [3].
NOTE:The pegs[3]should go in without effort.
WARNING: If the pegs go in only with difficulty, repeat the operation for fitting and
tensioning the timing belt
(see corresponding operation).
Refitting.
Remove tools [2]and [3].
Complete the refitting in reverse order to removal.
B1BP2V3D
B1EP1BAC
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 218

Downloaded from www.Manualslib.com manuals search engine 219
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ - RFN
Setting the timing.
Removing.
Disconnect the battery negative terminal
(see corresponding operation).
Raise and support the vehicle, front wheels hanging.
Remove:
- The front RH wheel.
- The plastic pins (1).
- The splash-shield (2).
- The accessories drive belt
(see corresponding operation).
Unclip and move aside the fuel delivery hose from the timing cover.
Remove the upper timing cover (1).
Turn the engine by means of the screw (3)of the crankshaft pulley (2)to bring it to the pegging position.
B1BP2V4C
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 219

Downloaded from www.Manualslib.com manuals search engine 220
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ - RFN
Setting the timing (continued).
A: Pegging on the manualgearbox.
B: Pegging on the automaticgearbox.
Peg:
- The crankshaft, using tool [2].
- The camshaft pulleys (5)and (6), using tool [1].
Remove:
- The screw (3)of the crankshaft pulley (2).
- The lower timing cover (4)
(by moving the engine).
IMPERATIVE: Never remove the crankshaft pulley (2) without pegging the crankshaft
and the camshafts.
Slacken the screw (9)of the tensioner roller (8).
Turn the tensioner roller (8)
(clockwise).
Remove the timing belt (7).
IMPERATIVE: Systematically replace the following components: timing belt, exhaust
manifold fixing nuts, timing belt tensioner roller nut.
B1BP2V3DB1EP1BBD
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 220

Downloaded from www.Manualslib.com manuals search engine 221
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ - RFN
Setting the timing (continued).
Turn the tensioner roller (8), using tool [5a]to go beyond slot «b».
Position the tool [5b]to lock the index «a»and remove the tool [5a].
Reposition the timing belt (7)on the crankshaft pulley.
Hold the timing belt (7)in place using tool [3].
Fit the timing belt (7)in place, respecting the following order:
- Guide roller (10).
- Inlet camshaft pulley (6).
- Exhaust camshaft pulley (5).
- Coolant pump (11).
-Tensioner roller (8).
NOTE:Make so that the belt (7)is as flush as possible with the exterior face of the various
pinions and rollers.
Remove:
- Tool [3].
- Tool [1]from the exhaust camshaft pulley.
- Tool [5b]from the tensioner roller (8).
Refit:
- The lower timing cover (4)
(by moving the engine).- The crankshaft pulley (2).
- Screw (3)of the crankshaft pulley.
Tighten screw (3) to 4 ± 0,4 m.daN, then angular tighten to 53°±4°, tool [4].
B1EP1BCDB1EP1BDC
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 221

Downloaded from www.Manualslib.com manuals search engine 222
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ - RFN
Tensioning the timing belt.
Turn the tensioner roller (8)in the direction of the arrow «c», by means of a hexagonal spanner at «d».
IMPERATVE: The index «a» should go past the slot «g» by an angular value of 10°.
If it does not, replace the tensioner roller or the timing belt and tensioner roller assembly.
Next bring the index «a» to its adjusting position «g», by turning the tensioner roller in the direction of
the arrow «e».
WARNING: the index «a» should not pass the slot «g».
Otherwise, repeat the operation to tension the timing belt.
IMPERATIVE: The tensioner roller should not turn during the tightening of its fixing.
If it does, repeat the operation to tension the timing belt.
Tighten the screw (9)of the tensioner roller (8)to 2,1 ± 0,2 m.daN.
IMPERATIVE: The hexagonal tensioner roller drive should be approx. 15° below the level of the cylinder
head gasket «h».
If it is not, replace the tensioner roller or the timing belt and tensioner roller assembly.
B1EP1BEC
B1EP1BFC
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 222