2005 Citroen C4 Battery

Downloaded from www.Manualslib.com manuals search engine 217
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Tools.
[1]Camshaft setting peg: (-) 0189.A
[2] Crankshaft setting peg: (-).0189.R
[3]Timing belt retaining pin: (-).0189.K
[4]Adaptor for angular tightening: 4069-T
[5]Tool for moving and locking the tensioner roller: (-).0189.S
[5a] : (-).0189.S1
[5b] : (-).0189 S2
Pliers for removing plastic pins: 7504-T
Checking the setting of the timing.
Removing.
Disconnect the battery negative terminal
(see corresponding operation).
Raise and support the vehicle, front wheels hanging.
Remove:
- The front RH wheel.
- The plastic pins (1).
- The splash-shield (2).
- The upper timing cover.
C4AP12TC
XSARA - XSARA PICASSO
Engines: 6FZ - RFN
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 217

Downloaded from www.Manualslib.com manuals search engine 219
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ - RFN
Setting the timing.
Removing.
Disconnect the battery negative terminal
(see corresponding operation).
Raise and support the vehicle, front wheels hanging.
Remove:
- The front RH wheel.
- The plastic pins (1).
- The splash-shield (2).
- The accessories drive belt
(see corresponding operation).
Unclip and move aside the fuel delivery hose from the timing cover.
Remove the upper timing cover (1).
Turn the engine by means of the screw (3)of the crankshaft pulley (2)to bring it to the pegging position.
B1BP2V4C
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 219

Downloaded from www.Manualslib.com manuals search engine 223
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 6FZ - RFN
Refitting (continued).
Remove the tools [1]and [2].
Rotate the crankshaft ten times
(normal direction of rotation).
IMPERATIVE: No pressure or outside force should be brought to bear on the timing belt.
Peg the inlet camshaft pulley, using tool [1].
Checks.
Tension of the timing belt.
ESSENTIAL: Check the position of the index «a», which should be opposite the slot «g».
If the position of the index «a» is not correct, repeat the operations to tension the timing belt.
Refit the upper timing cover (1).
Clip the fuel delivery hose on the timing cover.
Refit the accessories drive belt
(see corresponding operation).
Lower the vehicle.
Reconnect the battery
(see corresponding operation).
B1EP1BEC
B1EP1BFC
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 223

Downloaded from www.Manualslib.com manuals search engine 224
ENGINECHECKING THE VALVE TIMING
Engine: RFK
Tools.
[1]Camshaft setting peg: (-).0194.B
[2]Crankshaft setting peg: (-).0189.R
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking the timing.
Removing.
Disconnect the battery negative terminal.
Raise and support the vehicle, front wheels hanging.
Remove the front RH wheel and the splash-shield.
A:Pegging on the manualgearbox.
Turn the engine by means of the crankshaft pinion screw, to bring it to the pegging position.
Peg the crankshaft, using tool [2].
Unclip:
- The fuel supply hose from the upper timing cover.
- The fuel vapour re-induction circuit.
B1BP2V5D
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 224

Downloaded from www.Manualslib.com manuals search engine 225
ENGINE
CHECKING THE VALVE TIMING
Engine: RFK
Checking the timing (continued).
Suspend the engine, using a workshop hoist.
Remove:
- The RH engine support.
- The upper timing cover.
Peg the camshaft pulleys, using tool [1].
NOTE:The pegs [1] should go in without forcing.
WARNING: If the pegs go in only with difficulty, repeat the operation for fitting and tensioning
the timing belt
(see corresponding operation).
Remove the pegs [1]and [2].
Complete the refitting.
IMPERATIVE: Carry out the operations that are necessary following a reconnection of the battery
(see corresponding operation).
B1EP1GRC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 225

Downloaded from www.Manualslib.com manuals search engine 226
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: RFK
Tools.
[1]Camshaft setting peg: (-).0189.A
[2]Crankshaft setting peg: (-).0189.R
[3] Timing belt retaining pin: (-) 0189.K
[4]Adaptor for angular tightening: 4069-T
[5]Hub immobilising tool: (-).0189.S
[5a] : (-).0189.S1
[5b] : (-).0189.S2
Pliers for removing plastic pins: 7504-T
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking and setting the timing.
Removing.
Disconnect the negative terminal of the battery
(see corresponding operation).
Raise and support the vehicle, front wheels hanging.
Remove the auxiliaries drive belt
(see corresponding operation).
Unclip and move aside the fuel supply hose from the timing cover.
Remove the screw (1).
Move aside the power steering pipes.
Turn the engine by means of the screw (4)of the crankshaft pinion (3)to bring it to the pegging position.
B3EP15YC
B1BP36YC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 226

Downloaded from www.Manualslib.com manuals search engine 231
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: RFK
Checking and setting the timing (continued).
Refitting (continued).
Remove the tools [1]and [2].
Refit the upper RH engine support.
Remove the workshop hoist.
Rotate the crankshaft ten times
(normal direction of rotation).
IMPERATIVE: No exterior pressure or action should be applied on the timing belt.
Suspend the engine using a workshop hoist.
Remove the upper RH engine support.
Peg the inlet camshaft pulley, using tool [1].
Checking.
Timing belt tension.
IMPERATIVE: Check the position of the index «a», it should be opposite the slot «f». If the position of the index «a» is not correct, repeat
the operations to tension the timig belt.
Complete the refitting.
IMPERATIVE: Carry out the operations that are necessary following a reconnection of the battery
(see corresponding operation).
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 231

Downloaded from www.Manualslib.com manuals search engine 232
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 8HX - 8HZ
B1BP2LXC
Tools.
[1] Pliers for removing plastic pegs: 7504-T
[2]Lever for detensioning the dynamic tensioner roller: (-).0194.E
[3]Engine flywheel setting peg: (-).0194.C
[4] Camshaft setting peg: (-).0194.B
[5]Crankshaft and high pressure pump setting peg: (-).0194.A
Preliminary operations.
Remove:
- The front RH wheel.
- The front RH splash-shield, using tool [1].
- The clips of the electrical harness on the upper timing cover.
- The accessories belt, using tool [2]
(see corresponding operation).
Checking the setting.
Disconnect the battery negative cable.
Remove the upper timing cover (1).
Rotate the engine using the screw (2)of the crankshaft pulley.
NOTE:The locking hole is located under the crankshaft bearing cap cover.
Undo the screw (2).
Detension the auxiliary drive belt dynamic tensioner roller, using tool [2].
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 232