2005 Citroen C4 ESP

Downloaded from www.Manualslib.com manuals search engine 285
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Tools.
[1] Ø 10 mm low pressure connector: 4215-T
[2] Pressure gauge for testing boost pressure: 4073-T.A Toolkit 4073-T
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel injection
engines.
Remove the air filter duct.
Link tool [1]in series, downstream of the injectors, between the fuel high pressure pump and the
fuel filter at «a»and «b».
WARNING: Any checking of pressure downstream of the fuel filter is prohibited.
Switch on the ignition.
ESSENTIAL: Check that the tool [2] is clean.
Check the negative pressure according to the table below:
Vacuum Observations
10 ± 05 cmhgEngine driven by the starter motor
20 ± 20 cmhgEngine running under full load
60 ± 05 cmhgSupply circuit obstructed
(full tank strainer, piping, fuel filter
B1BP2PHC
Engines: 9HZ - 9HY
XSARA PICASSO
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 285

Downloaded from www.Manualslib.com manuals search engine 286
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Tools.
[1] Ø 10 mmlow pressure connector: 4215-T
[2]Pressure gauge for testing boost pressure: 4073-T.A Toolkit 4073-T
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel injection
engines.
Link tools [1] and [2]in series between the fuel high pressure pump and the fuel filter.
ESSENTIAL: Check that the tool [2] is clean.
Normal vacuum values.
Engine driven by the starter motor: 10 ± 0,5 cmHg.
Engine running under full load: 20 ± 10 cmHg.
Abnormal vacuum values.
Supply circuit obstructed
(full tank strainer, piping, fuel filter): 60 ± 20 cmHg.
B1BP33RD
Engine: RHR
C4
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 286

Downloaded from www.Manualslib.com manuals search engine 287
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Tools.
[1] Ø 10 mmlow pressure connector: 4215-T
[2] Pressure gauge for testing boost pressure: 4073-T.A Toolkit 4073-T
Checks.
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel injection
engines.
Link tools [1]and [2]in series between the fuel high pressure pump and the fuel filter.
ESSENTIAL: Check that the tool [2] is clean.
Vacuum Observations
10 ± 05 cmhgEngine driven by the starter motor
20 ± 20 cmhgEngine running under full load
60 ± 05 cmhgSupply circuit obstructed
(full tank strainer, piping, fuel filter)
B1BP2KUC
Engine: RHY
XSARA
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 287

Downloaded from www.Manualslib.com manuals search engine 290
INJECTION
CHECKS: TURBO PRESSURE
Tools.
[1]Pressure gauge for checking boost pressure: 4073-T.A
[2] Sleeve for checking boost pressure: (-).0171.F
Checks.
IMPERATIVE: Respect the following test conditions:
- Engine at operating temperature.
- Vehicle in running order.
- Engine under full load.
Preparation.
Remove the clips (1).
Fit the tool [2]in the place of the duct (2).
Couple the sleeve [2] on the pressure gauge[1]using the tube «a».
Mode of operation.
Position tool [1]in the vehicle.
Start the engine.
Engagefirst gear, start the vehicle.
Engage the gears up to third gear.
Decelerate to an engine speed of 1000 rpm.
Check the pressure: 0,6 ± 0,05bar
(1500 rpm).
Accelerate freely (change from fourth gear to third gear).Check the pressure: 0,9 ± 0,05bar (between 2500and 3500rpm).
Remove tools [1], [2] and «a».
Reposition the tube (2)and tighten the clips(1).
B1BP2NXD
C5FP06RC
Engines: 8HX - 8HZ
XSARA
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 290

Downloaded from www.Manualslib.com manuals search engine INJECTION
291
CHECKS: TURBO PRESSURE
IMPERATIVE: Respect the safety and cleanliness requirements.
Preparation.
IMPERATIVE: Respect the following test conditions:
- Engine at operating temperature.
- Vehicle in running order.
- Engine under full load.
Connect the diagnostic tool to the vehicle's diagnostic socket, carry out parameter measures.
Mode of operation.
Start the engine.
Engage first gear, start the vehicle.
Engage the gears up to third gear.
Decelerate to an engine speed of 1000 rpm.
Check the pressure: 0,6 ± 0,05 bar
(1500 rpm).
Accelerate freely (change from fourth gear to third gear).Check the pressure: 0,9 ± 0,05 bar (between 2500and 3500rpm).
Engines: 9HX - 9HY - 9HZ
C4
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 291

Downloaded from www.Manualslib.com manuals search engine 292
INJECTION
CHECKS: TURBO PRESSURE
IMPERATIVE: Respect the safety and cleanliness requirements.
Preparation.
IMPERATIVE: Respect the following test conditions:
- Engine at operating temperature.
- Vehicle in running order.
- Engine under full load.
Connect the diagnostic tool to the vehicle's diagnostic socket, carry out parameter measures.
Mode of operation.
Start the engine.
Engage first gear, start the vehicle.
Engage the gears up to third gear.
Decelerate to an engine speed of 1000 rpm.
Check the pressure: 0,6 ± 0,05 bar
(1500 rpm).
Accelerate freely (change from fourth gear to third gear).Check the pressure: 0,9 ± 0,05 bar (between 2500and 3500rpm).
Engines: 9HZ - 9HY
XSARA PICASSO
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 292

Downloaded from www.Manualslib.com manuals search engine 293
INJECTION
CHECKS: TURBO PRESSURE
Tools.
[1] Pressure gauge for checking the turbo pressure: 4073-T Toolkit 4073-T
[2]Pressure take-off extension: 8607-T.A
[3]Pressure take-off union and hose: 8607-T.B
[4] Sleeve for checking the turbo pressure: 4185-T
[5]Adaptor sleeve: 4219-T
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel injection
engines.
Preliminary operation.
Slacken the clip (1).
Uncouple the air duct (2).
Connect the tool [1]on tool [2]and the tool [3]on tool [2].
Positioning on the vehicle.
Insert the tools [4]and [5]between the air duct (2)and the turbo air cooler outlet at «a».
Connect the tool [3]on tool [4].
Position the tool [1]inside the vehicle.
Start the engine.
Accelerate to 4000 rpm.
The value should be: 1 ± 0,2.
Return the vehicle to conformity.
Remove tools [1], [2], [3], [4]and [5].
Recouple the air duct (2)on the turbo air cooler.
Tighten the clip (1).
B1BP356C
B1HP1ZXC
Engine: RHR
C4
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 293

Downloaded from www.Manualslib.com manuals search engine 294
INJECTION
CHECKS: TURBO PRESSURE
Tools.
[1]Pressure gauge for checking boost pressure: 4073-T.A Kit 4073-T
[2]Sleeve for checking boost pressure: 4185-T
Checks.
IMPERATIVE: respect the following checking requirements: Engine at running temperature.
Vehicle running at full load.
Preparation.
Remove the collar (3)and the sleeve.
Insert the tool [2]between the pipe (1)and the duct (2).
Position tool [1]in the vehicle.
Connect the pressure gauge [1]to the tool [2] with its tube «a»long enough for the gauge to be
positioned inside the vehicle.
Procedure.
Start the engine.
Engage first gearand start the engine.
Engage the gears up to third gear.
Decelerate to 2000 rpm.
Gradually accelerate.
Check the pressure: 0.95 ± 0.05 bar.
Remove the tools, refit the collars (3) and the sleeve.
B1BP1ZXD
Engine: RHY
XSARA PICASSO
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 294