2005 Citroen BERLINGO plate

Downloaded from www.Manualslib.com manuals search engine 92
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Lubrication
26 Oil gauge screw 1 ± 0,2
27 Oil level sensor fixing screw 1 ± 0,2
28 Drain plug 3,4 ± 0,3
29 Oil sump screw 0,8 ± 0,1
30 Oil pressure switch 2 ± 0,2
31 Oil strainer stud 0,6 ± 0,1
Oil pump screw
32Pre-tightening0,7
Tightening1 ± 0,1
33 Oil strainer fixing nuts 1,1 ± 0,1
34 Oil filter support screw 0,8 ± 0,2
35 Anti-emulsion plate fixing screw 1,9 ± 0,3
Engine: RFK
B1BP35RP
C4
Angl.-t2-page040-134-2005 9/01/06 10:11 Page 92

Downloaded from www.Manualslib.com manuals search engine 142
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Cylinder block
13 Front closing plate screw
Flywheel screws
14Pre-tightening1,5
Tightening4,7 ± 0,4
Accessories drive pulley screw
15Pre-tightening7 ± 0,25
Angular tightening60°±5°
Engine: RHR
B1CP0GNP
C4
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 142

Downloaded from www.Manualslib.com manuals search engine 160
ENGINEAUXILIARY EQUIPMENT DRIVE BELT
XSARA
(1)Tensioner roller fixing screw
(2)Tensioning screw
- New belt: 120 SEEMunits.
- Reused belt: 86.5 ± 3.5 SEEMunits.
(3)Tensioner roller fixing screw
(4)Tensioning screw
- New belt: 120 SEEMunits.
- Reused belt: 86.5 ± 3.5 SEEMunits.
NOTE:Removal of the tensioner roller makes it necessary to remove the plate with the upper fixing screw (5).
Without air conditioning
With air conditioning
B1BP1ANC
B1BP1AMC
Engine: NFU
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 160

Downloaded from www.Manualslib.com manuals search engine 185
ENGINE
Tools.
[1]Flywheel peg: 4507-T.A
[2] Camshaft pulley peg: 4507-T.B Toolkit 4507-T
[3]Square: 4507-T.J
[4] Belt tension measuring instrument: 4122-T
[5] Valve rocker thrust plate: 4533-T.Z
Checking the timing.
Peg the flywheel, using tool [1].
Peg the camshaft pulley, using tool [2].
Setting the timing.
NOTE:Remove the sparking plugs, to ease rotation of the crankshaft.
Rotate the engine by means of the crankshaft screw (1).
Peg the camshaft pinion.
Peg the flywheel
Slacken the nut (2).
Fullt detension the belt by acting on the tensioner roller.
Remove the belt.
IMPERATIVE: Check that the tensioner roller turns freely
(no tight spot).
CHECKING AND SETTING THE VALVE TIMING
Engines: KFW - NFV
B1EP067CB1EP066CB1EP068C
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 185

Downloaded from www.Manualslib.com manuals search engine 266
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: RHY - RHZ
Remove:
- The fixings of the pipe linking the power steering pump with the rotary valve.
- The clutch lower closing plate.
- Lock the engine flywheel, using tool [6].
Remove the screw (8).
Refit the screw (8)without its thrust washer.
Remove:
- The accessories pulley (9), using tool [8].
- Tool [6].
- The lower torque reaction rod.
Support the engine by means of a workshop hoist.
Remove:
- The bearing shell fitting (10).
- The nut (12).
- Screws (11).
- The bracket (13).
NOTE:Lift then lower the engine with the workshop hoist, to have access to the
timing cover fixing screws.
Remove:
- The intermediate timing cover.
- The lower timing cover.
B1CP04BCB1BP2R3CB1BP2R4C
XSARA - XSARA PICASSO
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 266

Downloaded from www.Manualslib.com manuals search engine 276
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: RHR
Refitting.
Centre the crankshaft pinion (15), using tool [5].
Reposition the timimg belt on the pulley (18).
Put the tool [4]in place
(tighten moderately).
Reposition the timimg belt, strip «a»well tensioned
in the following order:
- Guide roller (14).
- Crankshaft pinion (15).
- Coolant pump pinion (16).
- Tensioner roller (17).
Remove tools [4]and [5].
Bring the index «d»outside the plate at «c», by
turning the tensioner roller in the direction of the
arrow «b», using a hexagonal spanner at «e».
Tighten screw (12)of the tensioner roller (17)to
2,1 ± 0,2 m.daN.
Lock the flywheel, by means of tool [6].
Refit the auxiliaries drive pulley (7).
Tighten the screw (8)to 7 ± 0,7 m.daN.
Remove tools [6], [2]and [3].
B1EP1FFC
B1EP1FGC
B1EP1FHC
B1EP1FJC
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 276

Downloaded from www.Manualslib.com manuals search engine 315
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS
Engines: KFU - NFU - RFN - RFJ - RFK - 9HX - 9HY - 9HZ - RHR
NOTE:All the clutches are «push»type with hydraulic control.
NOTE:The DV6TED4and DW10BTED4engines are equipped with a double damping flywheel (DVA).
Description.
The declutch control has a declutch fork with a ball-joint on the axis.
(1)The ball-joint is screwed into the clutch casing
(2) Declutch fork
(3)Clutch casing
(4)Bearing
(5) Clutch plate
The clutch control slave cylinder(7)is fixed by two screws (6) into the exterior of the clutch casing.
B2BP047C
B2CP3FAC
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 315

Downloaded from www.Manualslib.com manuals search engine 316
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS
Engines: KFW - NFU - NFV - 6FZ - RFN - 8HX - 8HZ - 9HY - 9HZ - WJY - RHY - RHZ
NOTE:All the clutches are «push»type with hydraulic control.
Description.
The declutch control has a declutch fork mounted on a ball-joint.
(1)The ball-joint is screwed into the clutch casing
(2)Declutch fork
(3)Clutch casing
(4)Bearing
(5)Clutch plate
The clutch control slave cylinder (7)is fixed by two screws (6)onto the exterior of the clutch casing.
T
ightening torques (m.daN).
Fixing of clutch plate/engine flywheel: 2 ± 0,2.
Fixing of clutch control slave cylinder / clutch housing: 2 ± 0,25.
Fixing of engine flywheel/crankshaft
Pre-tightening: 1,75 ± 0,2.
Angular tightening: 75° ± 5°.
Checking torque: 6,3 ± 2,2.
B2BP047CB2BP05SC
XSARA - XSARA PICASSO
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 316