2005 Citroen BERLINGO wheel

Downloaded from www.Manualslib.com manuals search engine 388
AXLES
SUSPENSION
STEERING
H1 = R1 – L1 H1’ = R1 – L1’
H1 = From the front suspension arm linkage bolt axis to the ground.
R1 =Radius of the front wheel when laden.
L1 =From the centre of the wheel to the front suspension arm linkage
bolt axis.
H1' =From the front jacking point to the ground.
L1' =From the front jacking point to the radius of the front wheel when
laden.H2 = R2 - L2
H2 = From the rear axle silentblock face to the ground.
R2 =Radius of the rear wheel when laden.
L2 =From the centre of the wheel to the rear axle silentblock face.
AXLE GEOMETRY
Measurements at reference height
NOTE: To make the setting of reference height easier, it is acceptable to take the measurement from the flange of the jacking point.
WARNING: The values shown should only be used as guides. In case of doubt, check the settings at reference height
Rear heightFront height
B3CP05BCB3CP058DB3DP079C
XSARA PICASSO
Conditions for checking and adjusting: Tyres inflated to correct pressures. Vehicle at reference height. Steering rack locked at mid point(see corresponding operation).
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 388

Downloaded from www.Manualslib.com manuals search engine 389
AXLES
SUSPENSION
STEERING
AXLE GEOMETRY
(*) = Difficult road conditions.
Compress the suspension to obtain the calculated values.
NOTE: The difference in height between the two sides should be less than10 mm. Measure the radius of the rear wheel: R2.
Calculate the dimensionH2. Measure the radius of the front wheel: R1.
Calculate the dimension H1 ouH1’.
Measurements at reference height (the reference height of the vehicle is set as per the table below).
B3CP05BCB3CP05AC
XSARA PICASSO
Front axleRear axle
Front axle
Rear axle Vehicles all engine versions (except CRD (*))
H1 = R1 – L1 or H1’ = R1 – L1’
L1 = 90,5 mmL1’ = 124 mmL2 = 8,5 mm H2 = R2 + L2
B3DP079C
Value at reference height (-8/+3 mm)Value at reference height (+10/-3 mm)
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 389

Downloaded from www.Manualslib.com manuals search engine 391
AXLES
SUSPENSION
STEERING
AXLE GEOMETRY
(*) = Difficult road conditions.
Compress the suspension to obtain the calculated values.
NOTE: The difference in height between the two sides should be less than10 mm. Measure the radius of the rear wheel: R2.
Calculate the dimensionH2. Measure the radius of the front wheel: R1.
Calculate the dimension H1 orH1’.
Checks at reference height (the reference height of the vehicle is set as per the table below).
B3CP05BCB3CP05AC
XSARA PICASSO
Front axleRear axle
Front axle
Rear axle CRD vehicle versions (*)
H1 = R1 – L1 or H1’ = R1 – L1’
L1 = 75,5 mmL1’ = 109 mmL2 = 23,5 mmH2 = R2 + L2
B3DP079C
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 391

Downloaded from www.Manualslib.com manuals search engine 393
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: FRONT AXLE
Tightening torques (m.daN).(1) Damper nut: 4.5 ± 0.4
(2)Cup screw: 2.5 ± 0.2
(3)Suspension leg
(4)Anti-roll bar link rod ball-joint: 3.7 ± 0.3
(5)Suspension leg swivel: 4.5 ± 0.4
(6)Anti-roll bar
(7)Anti-roll bar link rod ball-joint: 3.7 ± 0.3
(8)Lower swivel ball-joint: 4 ± 0.4
(9)Hub nut
(greased): 32.5 ± 2
(10)Wheel bolt
(face and threads not greased): 9 ± 1
(11) Lower arm front pivot: 7.6 ± 0.7
(12) Lower arm rear pivot and
anti-roll bar bearing: 6.8 ± 0.6
(13) Screw under rear pivot : 3.5 ± 0.3
Lower arm in forged steel : 3.7 ± 0,3
Lower arm in plate steel: 3.1 ± 0,3
Screw fixing subframe on bodyshell: 8.5 ± 0,8
Screw fixing ball-joint on lower
arm
(plate steel): 4.5 ± 0,4
Anti-roll bar
Engines
ALL TYPESDiameter
21Colour ref.
WHITE Suspension leg angle:
Ta b«a»towards the front.
B3CP056P
B3CP057D
B3CP043D
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 393

Downloaded from www.Manualslib.com manuals search engine 394
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: REAR AXLE
Tightening torques (m.daN).
(14)Front silentblock on subframe: 9.4 ± 0.9
(15)Anti-roll bar bolt: 5.5 ± 0.5
(16)Rear torsion bar
(17) Anti-roll bar
(18) Tubular axle
(19)Front silentblock on bodyshell: 4 ± 0.4
(20)Rear upper arm.
(21)Wheel bolt
(face and threads not lubricated): 9 ± 1
(22)Damper
(23)Rear silentblock on subframe: 5.4 ± 0.5
(24)Damper pin nut: 11 ± 1
(25)Stub axle nuts
(lubricated): 25 ± 2
(26)Rear silentblock on bodyshell: 6.5 ± 0.6
Anti-roll bar
Torsion bar
Engines
ALL TYPES 19,6 PINKØ (mm)
Colour ref.Ø (mm)
21Colour ref.
ORANGE
B3DP078D
NOTE: The RH torsion bar can be identified by 1 paint line.
The LH torsion bar can be identified by 2 paint lines.
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 394

Downloaded from www.Manualslib.com manuals search engine 395
AXLES
SUSPENSION
STEERING
TIGHTENING TORQUES: POWER-ASSISTED STEERING
Tightening torques (m.daN).
(2) Airbag to steering wheel fixing: 0.8 ± 0.1
(3)Steering wheel fixing: 3.3 ± 0.6
(5)Steering column to support fixing: 4 ± 0.1
(6)Steering cardan joint fixing: 2.3 ± 0.2
B3EP116D
XSARA PICASSO
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 395

Downloaded from www.Manualslib.com manuals search engine B3FP7E1D
BRAKE SPECIFICATIONS
Braking system.
Braking circuit in the form of an X.
Disc brakes at the front and at the rear
(vehicles all types):
- The front brake discs are ventilated.
- The rear brake discs are plain.
NOTE: The front brake pads have no wear warning
lamp.
Handbrake lever controlled by cables acting on the
rear wheels.
The compensator and main brake limiter functions
are assured by the ABS REF systems.
NOTE:REF = Electronic Brakeforce Distribution (EBD).
400
BRAKESC4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 400

Downloaded from www.Manualslib.com manuals search engine 401
BRAKES
TIGHTENING TORQUES: BRAKING SYSTEM
Front brakes
1Front brake disc1 ± 0,1
2Yoke on caliper3 ± 0,3
3Unions on brake piping1,5 ± 0,1
4Caliper on pivot10,5 ± 1
5ABS/ESP hydraulic block support on the chassis member0,2 ± 0,1
6Wheel sensor0,8 ± 0,1
B3FP7DVD
B3FP7DWD
C4
Angl.-t2-PAGE398-427-2005 9/01/06 10:24 Page 401