2005 CHRYSLER CARAVAN weight

(7) Connect the heater lines to the heater hoses at
the heater core and EGR port. Position spring clamps
onto the hoses.
(8) Fill the engine cooling system (Refer to 7 -
COOLING - STANDARD PROCEDURE).
HEATER UNIT
REMOVAL
WARNING: DO NOT OPERATE THE DIESEL SUP-
PLEMENTAL CABIN HEATER IN AN ENCLOSED
AREA SUCH AS A GARAGE THAT DOES NOT HAVE
EXHAUST VENTILATION FACILITIES. ALWAYS VENT
THE CABIN HEATER EXHAUST WHEN OPERATING
THE CABIN HEATER. ALLOW THE DIESEL SUPPLE-
MENTAL CABIN HEATER TO COOL BEFORE PER-
FORMING ANY SERVICE PROCEDURES TO THE
CABIN HEATER. VERIFY THAT ALL DIESEL SUP-
PLEMENTAL CABIN HEATER FUEL LINES ARE
SECURELY FASTENED TO THEIR RESPECTIVE
COMPONENTS BEFORE PERFORMING ANY SER-
VICE PROCEDURES TO THE CABIN HEATER. FAIL-
URE TO FOLLOW THESE INSTRUCTION MAY
RESULT IN PERSONAL INJURY OR DEATH.(1) Raise and support the vehicle. Take note of the
location of the flexible section of the cabin heater
exhaust tube.
(2) Drain the engine cooling system (Refer to 7 -
COOLING - STANDARD PROCEDURE).
(3) Carefully open one hose to the underbody tube
assembly and drain the remaining coolant. A salvage
hose is a good idea to control the residual coolant, as
flow will occur from both the cabin heater and the
hose and tube assemblies.
(4) Remove the second hose from the underbody
hose and tube assembly.
(5) Loosen the hose and tube assembly from the
toe-board crossmember at two locations.
(6) Disconnect the electrical connector from the
body harness near the toe-board crossmember and
rail.
(7) Remove the wiring harness from the toe-board
crossmember (Refer to 24 - HEATING & AIR CON-
DITIONING/CABIN HEATER/HEATER UNIT -
REMOVAL).
(8) Open the fuel filler cap. Disconnect the rubber
fuel hose between the body tube assembly and the
fuel pump nipple at the body tube joint. A minimal
amount of fuel may flow from the open port.
NOTE: Utilize an approved fuel storage container to
catch any residual fuel.
(9) Loosen the two fasteners at the rail. Take care
to notice that the exhaust tube bracket tab is on top
of the heater bracket and that there are two spacer
washers installed between the rubber grommets.
(10) Remove the flexible section of the cabin
heater exhaust tube from the exhaust tube by loos-
ening the clamp. Remove the hose from the exhaust
tube. Removal of the rail tube assembly may aid in
this service operation (Refer to 24 - HEATING & AIR
CONDITIONING/CABIN HEATER/EXHAUST TUBE
- REMOVAL).
(11) Remove seat hex nut at the heater mounting
flange to crossmember.
(12) Loosen the remaining fasteners which mount
the exhaust tube assembly to the vehicle.
(a) Install a suitable support device under the
cabin heater and secure the cabin heater to the
support.
(13) Loosen the remaining three fasteners to the
crossmembers.
(14) Remove the loosened fasteners that support
the cabin heater while supporting the weight of the
heater.
(15) Swing the cabin heater mounting bracket
from between the exhaust bracket and rail mounting
location. Drain any residual coolant from the cabin
heater.
Fig. 7 Cabin Heater Air Intake And Heater Pipe
Assembly
1 - INTAKE TUBE AIR INTAKE
2 - INTAKE PIPE
3 - RETAINING SCREWS
4 - INTAKE HEATER LINE
5 - RETURN HEATER LINE
RSCABIN HEATER24 - 121
HEATER PIPES (Continued)

BENCH SEAT RISER - 50/50 SPLIT -INSTALLATION ...................... 23-145
BENCH SEAT RISER - 50/50 SPLIT - REMOVAL ......................... 23-145
BENCH SEAT RISER - SECOND ROW - INSTALLATION ...................... 23-145
BENCH SEAT RISER - SECOND ROW - REMOVAL ......................... 23-145
BENCH SEAT RISER - THIRD ROW - INSTALLATION ...................... 23-145
BENCH SEAT RISER - THIRD ROW - REMOVAL ......................... 23-145
BENCH SEAT TRACK - INSTALLATION . . . 23-148
BENCH SEAT TRACK - REMOVAL .......23-148
BEZEL - INSTALLATION, CLUSTER .......23-65
BEZEL - INSTALLATION, INSTRUMENT PANEL CENTER ...................... 23-72
BEZEL - INSTALLATION, SLIDING DOOR STOP BUMPER ...................... 23-25
BEZEL - REMOVAL, CLUSTER ...........23-65
BEZEL - REMOVAL, INSTRUMENT PANEL CENTER ............................ 23-71
BEZEL - REMOVAL, SLIDING DOOR STOP BUMPER ...................... 23-25
BEZEL OUTLETS, INSTALLATION - FRONT CENTER ...................... 24-45
BEZEL OUTLETS, REMOVAL - FRONT CENTER ............................ 24-44
BIN - INSTALLATION, UNDER SEAT STORAGE .......................... 23-149
BIN - REMOVAL, UNDER SEAT STORAGE . 23-149
BIN GUIDE - INSTALLATION, UNDER SEAT STORAGE ..................... 23-150
BIN GUIDE - REMOVAL, UNDER SEAT STORAGE .......................... 23-150
BIN LOCK/LATCH - INSTALLATION, UNDER SEAT STORAGE ...............23-150
BIN LOCK/LATCH - REMOVAL, UNDER SEAT STORAGE ..................... 23-150
BLADDER & PRESSURE SENSOR - DESCRIPTION, SEAT WEIGHT ...........8O-43
BLADDER & PRESSURE SENSOR - OPERATION, SEAT WEIGHT ............8O-44
BLADES - CLEANING, WIPER ...........8R-13
BLADES - INSTALLATION, WIPER ........8R-13
BLADES - REMOVAL, WIPER ...........8R-13
BLEEDING - STANDARD PROCEDURE, ANTILOCK BRAKE SYSTEM ..............5-90
BLEEDING - STANDARD PROCEDURE, BASE BRAKE ..........................5-8
BLEEDING - STANDARD PROCEDURE, MASTER CYLINDER ................... 5-36
BLEND DOOR ACTUATOR - DESCRIPTION .................. 24-22,24-34
BLEND DOOR ACTUATOR - INSTALLATION .................. 24-22,24-35
BLEND DOOR ACTUATOR - OPERATION . . 24-22, 24-35
BLEND DOOR ACTUATOR - REMOVAL ....24-22,
24-35
BLOCK - CLEANING, ENGINE .......9-115,9-37
BLOCK - DESCRIPTION, BLOWER MOTOR RESISTOR ..............24-24,24-37
BLOCK - DESCRIPTION, ENGINE .....9-115,9-36
BLOCK - DESCRIPTION, NON-ABS JUNCTION ........................... 5-33
BLOCK - INSPECTION, ENGINE ......9-115,9-37
BLOCK - INSTALLATION, NON-ABS JUNCTION ........................... 5-34
BLOCK - OPERATION, BLOWER MOTOR RESISTOR ..................... 24-24,24-37
BLOCK - OPERATION, NON-ABS JUNCTION ........................... 5-33
BLOCK - REMOVAL, NON-ABS JUNCTION . . 5-34
BLOCK, DIAGNOSIS AND TESTING - FRONT BLOWER MOTOR RESISTOR ......24-25
BLOCK, DIAGNOSIS AND TESTING - REAR BLOWER MOTOR RESISTOR ......24-38
BLOCK HEATER - DESCRIPTION, ENGINE . . . 7-20
BLOCK HEATER - INSTALLATION, ENGINE ............................. 7-21
BLOCK HEATER - OPERATION, ENGINE ....7-20
BLOCK HEATER - REMOVAL, ENGINE ......7-21
BLOCK HEATER TESTING - DIAGNOSIS AND TESTING, ENGINE .................7-21
BLOCKER AIRBAG - DESCRIPTION, KNEE . 8O-22
BLOCKER AIRBAG - INSTALLATION, KNEE .............................. 8O-23BLOCKER AIRBAG - OPERATION, KNEE . . . 8O-22
BLOCKER AIRBAG - REMOVAL, KNEE
....8O-23
BLOCKER- INFLATABLE KNEE - INSTALLATION ....................... 23-75
BLOCKER- INFLATABLE KNEE - REMOVAL .......................... 23-75
BLOCKER LATCH - INSTALLATION, FUEL FILL DOOR ......................... 23-53
BLOCKER LATCH - REMOVAL, FUEL FILL DOOR ............................. 23-53
BLOCKER LATCH STRIKER - INSTALLATION, FUEL FILL DOOR ........23-53
BLOCKER LATCH STRIKER - REMOVAL, FUEL FILL DOOR ..................... 23-53
BLOCKER LOCKOUT LINK - INSTALLATION, FUEL FILL DOOR ........23-54
BLOCKER LOCKOUT LINK - REMOVAL, FUEL FILL DOOR ..................... 23-54
BLOWER MOTOR - DESCRIPTION . . 24-45,24-57
BLOWER MOTOR - DESCRIPTION, POWER MODULE .................... 24-30
BLOWER MOTOR - DESCRIPTION, POWER MODULE - REAR ..............24-40
BLOWER MOTOR - INSTALLATION, POWER MODULE .................... 24-31
BLOWER MOTOR - INSTALLATION, POWER MODULE - REAR ..............24-41
BLOWER MOTOR - OPERATION ....24-45,24-57
BLOWER MOTOR - OPERATION, POWER MODULE ........................... 24-30
BLOWER MOTOR - OPERATION, POWER MODULE - REAR ..................... 24-40
BLOWER MOTOR - REMOVAL, POWER MODULE ........................... 24-30
BLOWER MOTOR - REMOVAL, POWER MODULE - REAR ..................... 24-41
BLOWER MOTOR, DIAGNOSIS AND TESTING - FRONT .................... 24-46
BLOWER MOTOR, DIAGNOSIS AND TESTING - REAR ..................... 24-58
BLOWER MOTOR RELAY - DESCRIPTION . 24-23, 24-36
BLOWER MOTOR RELAY - INSTALLATION .................. 24-24,24-37
BLOWER MOTOR RELAY - OPERATION . . . 24-23, 24-36
BLOWER MOTOR RELAY - REMOVAL ....24-24,
24-37
BLOWER MOTOR RESISTOR BLOCK - DESCRIPTION .................. 24-24,24-37
BLOWER MOTOR RESISTOR BLOCK - OPERATION .................... 24-24,24-37
BLOWER MOTOR RESISTOR BLOCK, DIAGNOSIS AND TESTING - FRONT ......24-25
BLOWER MOTOR RESISTOR BLOCK, DIAGNOSIS AND TESTING - REAR .......24-38
BODY - ASSEMBLY, VALVE ......21-139,21-291
BODY - DESCRIPTION, THROTTLE .......14-39
BODY - DESCRIPTION, VALVE ....21-132,21-283
BODY - DISASSEMBLY, VALVE . . . 21-135,21-286
BODY - INSTALLATION, THROTTLE .......14-40
BODY - INSTALLATION, VALVE . . . 21-144,21-295
BODY - OPERATION, THROTTLE .........14-39
BODY - OPERATION, VALVE .....21-132,21-283
BODY - REMOVAL, THROTTLE ..........14-40
BODY - REMOVAL, VALVE .......21-133,21-284
BODY AND CABLE - DESCRIPTION, ANTENNA ........................... 8A-7
BODY AND CABLE - OPERATION, ANTENNA ........................... 8A-7
BODY AND CABLE, DIAGNOSIS AND TESTING - ANTENNA ................... 8A-8
BODY CONTROL MODULE - DESCRIPTION ........................ 8E-2
BODY CONTROL MODULE - INSTALLATION ........................ 8E-4
BODY CONTROL MODULE - OPERATION . . . 8E-3
BODY CONTROL MODULE - REMOVAL .....8E-4
BODY LUBRICATION, SPECIFICATIONS ....23-12
BODY OPENING DIMENSIONS - SPECIFICATIONS .................... 23-180
BODY PANEL REPAIR - STANDARD PROCEDURE, PLASTIC .................23-3
BODY SEALING LOCATIONS - FOLD-IN- FLOOR ONLY - SPECIFICATIONS ........23-209
BODY SEALING LOCATIONS - SPECIFICATIONS .................... 23-183
BODY SIDE - INSTALLATION ............23-44BODY SIDE - REMOVAL
...............23-44
BODY SIDE MOLDINGS - INSTALLATION . . 23-46
BODY SIDE MOLDINGS - REMOVAL ......23-45
BODY, SPECIAL TOOLS ................23-13
BOLSTER - INSTALLATION, QUARTER TRIM .............................. 23-95
BOLSTER - REMOVAL, QUARTER TRIM . . . 23-95
BOOSTER - DESCRIPTION, POWER BRAKE .............................. 5-45
BOOSTER - DIAGNOSIS AND TESTING, POWER BRAKE ....................... 5-46
BOOSTER - OPERATION, POWER BRAKE . . . 5-46
BOOT - INNER - INSTALLATION, CV ........3-7
BOOT - INNER - REMOVAL, CV ...........3-6
BOOT - OUTER - INSTALLATION, CV ......3-11
BOOT - OUTER - REMOVAL, CV ..........3-10
BORE FITTING - STANDARD PROCEDURE, PISTON TO CYLINDER ......9-44
BORE HONING - STANDARD PROCEDURE, CYLINDER ...........9-115,9-36
BOTTOM OF SEAT CUSHION PAN PANEL-THIRD ROW - FOLD-IN-FLOOR
- INSTALLATION .................... 23-152
BOTTOM OF SEAT CUSHION PAN PANEL-THIRD ROW - FOLD-IN-FLOOR
- REMOVAL ........................ 23-152
BOX - INSTALLATION, GLOVE ...........23-66
BOX - REMOVAL, GLOVE ..............23-66
BOX LAMP SWITCH - INSTALLATION, GLOVE ............................. 8L-22
BOX LAMP SWITCH - REMOVAL, GLOVE . . 8L-22
BOX LATCH - INSTALLATION, GLOVE .....23-66
BOX LATCH - REMOVAL, GLOVE .........23-66
BOX LATCH STRIKER - INSTALLATION, GLOVE ............................. 23-66
BOX LATCH STRIKER - REMOVAL, GLOVE ............................. 23-66
B-PILLAR - INSTALLATION, A-PILLAR- HEADER, OR ........................ 23-17
B-PILLAR - REMOVAL, A-PILLAR- HEADER, OR ........................ 23-17
B-PILLAR LOWER TRIM - INSTALLATION . . 23-80
B-PILLAR LOWER TRIM - REMOVAL .....23-79
B-PILLAR SWITCH - DESCRIPTION ......8N-52
B-PILLAR SWITCH - INSTALLATION ......8N-52
B-PILLAR SWITCH - OPERATION ........8N-52
B-PILLAR SWITCH - REMOVAL .........8N-52
B-PILLAR UPPER TRIM - INSTALLATION . . 23-80
B-PILLAR UPPER TRIM - REMOVAL ......23-80
BRACKET - DESCRIPTION, TRANSVERSE . . 8N-19
BRACKET - INSTALLATION, TRANSVERSE . 8N-19
BRACKET - OPERATION, TRANSVERSE . . . 8N-19
BRACKET - REMOVAL, TRANSVERSE .....8N-19
BRACKET, 2.4L ENGINE - A/C COMPRESSOR MOUNTING ........24-74,24-75
BRAKE - DESCRIPTION, CONTROLLER ANTILOCK ........................... 8E-4
BRAKE - INSTALLATION, CONTROLLER ANTILOCK ........................... 8E-6
BRAKE - INSTALLATION, LEVER - PARKING ............................ 5-76
BRAKE - INSTALLATION, SHOES - PARKING ............................ 5-84
BRAKE - INSTALLATION, SUPPORT PLATE - DRUM ....................... 5-61
BRAKE - OPERATION, CONTROLLER ANTILOCK ........................... 8E-5
BRAKE - REMOVAL, CONTROLLER ANTILOCK ........................... 8E-5
BRAKE - REMOVAL, LEVER - PARKING ....5-75
BRAKE - REMOVAL, SHOES - PARKING ....5-78
BRAKE - REMOVAL, SUPPORT PLATE - DRUM .............................. 5-61
BRAKE AUTOMATIC ADJUSTER - DIAGNOSIS AND TESTING, DRUM ........5-14
BRAKE AUTOMATIC ADJUSTER TENSION RELEASE - STANDARD PROCEDURE,
PARKING ............................ 5-63
BRAKE AUTOMATIC ADJUSTER TENSION RESET - STANDARD PROCEDURE,
PARKING ............................ 5-64
BRAKE BLEEDING - STANDARD PROCEDURE, BASE .....................5-8
BRAKE BOOSTER - DESCRIPTION, POWER ............................. 5-45
BRAKE BOOSTER - DIAGNOSIS AND TESTING, POWER ..................... 5-46
BRAKE BOOSTER - OPERATION, POWER . . . 5-46
4 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

POWER MODULE - INSTALLATION,INTEGRATED ......................8W -97-2
POWER MODULE - OPERATION, INTEGRATED ......................8W -97-2
POWER MODULE - REAR BLOWER MOTOR - DESCRIPTION ...............24-40
POWER MODULE - REAR BLOWER MOTOR - INSTALLATION ...............24-41
POWER MODULE - REAR BLOWER MOTOR - OPERATION .................24-40
POWER MODULE - REAR BLOWER MOTOR - REMOVAL .................. 24-41
POWER MODULE - REMOVAL, INTEGRATED ......................8W -97-2
POWER OUTLET - DESCRIPTION ......8W-97-3
POWER OUTLET - DIAGNOSIS & TESTING .........................8W -97-3
POWER OUTLET - OPERATION ........8W-97-3
POWER SEAT SYSTEM, DESCRIPTION ....8N-31
POWER SEAT SYSTEM, DIAGNOSIS AND TESTING ........................... 8N-33
POWER SEAT SYSTEM, OPERATION .....8N-32
POWER SEAT TRACK - DESCRIPTION ....8N-37
POWER SEAT TRACK - OPERATION ......8N-38
POWER SEAT TRACK, DIAGNOSIS AND TESTING ........................... 8N-38
POWER SLIDING DOOR ADJUSTMENT, STANDARD PROCEDURE ..............8N-49
POWER SLIDING DOOR LEARN CYCLE, STANDARD PROCEDURE ..............8N-48
POWER SLIDING DOOR SYSTEM - DESCRIPTION ........................ 8N-40
POWER SLIDING DOOR SYSTEM - OPERATION ......................... 8N-41
POWER SLIDING DOOR SYSTEM, DIAGNOSIS AND TESTING .............8N-42
POWER STEERING BELT TENSION - STANDARD PROCEDURE, CHECKING .......7-8
POWER STEERING FASTENER TORQUE, SPECIFICATIONS ...................... 19-9
POWER STEERING FLUID LEVEL CHECKING - STANDARD PROCEDURE ....19-44
POWER STEERING GEAR, SPECIAL TOOLS ............................. 19-34
POWER STEERING PUMP INITIAL OPERATION - STANDARD PROCEDURE . . . 19-37
POWER STEERING PUMP, SPECIAL TOOLS ............................. 19-44
POWER STEERING, SPECIAL TOOLS ......19-9
POWER STEERING SYSTEM - DESCRIPTION ........................ 19-1
POWER STEERING SYSTEM - OPERATION .......................... 19-1
POWER STEERING SYSTEM FLOW AND PRESSURE TEST - DIAGNOSIS AND
TESTING ............................ 19-1
POWER TRANSFER UNIT FLUID - DESCRIPTION, AWD ....................0-6
POWER WINDOWS - DESCRIPTION ......8N-61
POWER WINDOWS - OPERATION ........8N-61
POWER WINDOWS, DIAGNOSIS AND TESTING ........................... 8N-61
POWERING SEVERAL LOADS - STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-10
PRELOAD - ADJUSTMENT, DIFFERENTIAL BEARING ..............21-228
PRELOAD MEASUREMENT AND ADJUSTMENT, ADJUSTMENTS -
DIFFERENTIAL BEARING ...............21-79
PREPARATION - STANDARD PROCEDURE, ENGINE GASKET
SURFACE ........................ 9-11,9-87
PRESSURE - DIAGNOSIS AND TESTING, CHECKING ENGINE OIL .................9-53
PRESSURE - DIAGNOSIS AND TESTING, ENGINE OIL ......................... 9-138
PRESSURE CAP - DESCRIPTION, RADIATOR ........................... 7-27
PRESSURE CAP - OPERATION, RADIATOR ........................... 7-27
PRESSURE CAP TESTING - DIAGNOSIS AND TESTING, COOLING SYSTEM ........7-28
PRESSURE FOR HIGH SPEED OPERATION - STANDARD PROCEDURE,
TIRE ............................... 22-17
PRESSURE GAUGE - STANDARD PROCEDURE, FUEL .................... 14-3PRESSURE LEAKAGE TEST - DIAGNOSIS
AND TESTING, CYLINDER
COMBUSTION ..................... 9-85,9-9
PRESSURE MONITORING - DESCRIPTION, TIRE ................... 22-9
PRESSURE MONITORING - OPERATION, TIRE ............................... 22-10
PRESSURE REGULATOR - INSTALLATION, FUEL .................. 14-7
PRESSURE REGULATOR - OPERATION, FUEL ............................... 14-7
PRESSURE REGULATOR - REMOVAL, FUEL ............................... 14-7
PRESSURE RELEASE PROCEDURE - STANDARD PROCEDURE, FUEL
SYSTEM ............................ 14-2
PRESSURE RELIEF VALVE - INSTALLATION, OIL ................... 9-144
PRESSURE RELIEF VALVE - REMOVAL, OIL................................ 9-143
PRESSURE RELIEF VALVE, DESCRIPTION - HIGH ............................. 24-72
PRESSURE RELIEF VALVE, OPERATION - HIGH .............................. 24-72
PRESSURE SENSOR - DESCRIPTION, SEAT WEIGHT BLADDER ...............8O-43
PRESSURE SENSOR - DIAGNOSIS AND TESTING, TIRE ...................... 22-11
PRESSURE SENSOR - OPERATION, SEAT WEIGHT BLADDER ................... 8O-44
PRESSURE, SPECIFICATIONS - FUEL SYSTEM ............................ 14-4
PRESSURE SWITCH - DESCRIPTION, OIL . 9-144
PRESSURE SWITCH - INSTALLATION, OIL ........................... 9-144,9-56
PRESSURE SWITCH - OPERATION, OIL . . . 9-144
PRESSURE SWITCH - REMOVAL, OIL ....9-144,
9-56
PRESSURE TEST - DIAGNOSIS AND TESTING, CYLINDER COMPRESSION . . . 9-85,9-9
PRESSURE TEST - DIAGNOSIS AND TESTING, POWER STEERING SYSTEM
FLOW ............................... 19-1
PRESSURE TESTS - DIAGNOSIS AND TESTING, CLUTCH AIR ...........21-153,21-8
PRESSURE TESTS - DIAGNOSIS AND TESTING, HYDRAULIC ............21-150,21-6
PRESSURE TRANSDUCER - DESCRIPTION, A/C ................... 24-20
PRESSURE TRANSDUCER - OPERATION, A/C................................ 24-20
PRESSURE TRANSDUCER, DIAGNOSIS AND TESTING - A/C ................... 24-21
PRESSURES - STANDARD PROCEDURE, TIRE INFLATION ..................... 22-16
PROGRAMMABLE COMMUNICATIONS INTERFACE (PCI) BUS, OPERATION ......14-25
PROGRAMMING - STANDARD PROCEDURE, PCM/SKIM ................8E-1
PROGRAMMING - STANDARD PROCEDURE, REMOTE KEYLESS
ENTRY TRANSMITTER ................8N-24
PROGRAMMING - STANDARD PROCEDURE, TRANSPONDER ...........8Q-6
PROGRAMMING, STANDARD PROCEDURE - ELECTRONIC VEHICLE
INFORMATION CENTER ................8M-8
PROP ROD - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, SEAT .........23-140
PROP ROD - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, SEAT .............23-139
PROPORTIONING - DESCRIPTION, ELECTRONIC VARIABLE BRAKE ..........5-88
PROPORTIONING - OPERATION, ELECTRONIC VARIABLE BRAKE ..........5-89
PROPORTIONING VALVE (HEIGHT SENSING) - DESCRIPTION ..............5-53
PROPORTIONING VALVE (HEIGHT SENSING) - DIAGNOSIS AND TESTING .....5-54
PROPORTIONING VALVE (HEIGHT SENSING) - INSTALLATION ..............5-55
PROPORTIONING VALVE (HEIGHT SENSING) - OPERATION ................5-53
PROPORTIONING VALVE (HEIGHT SENSING) - REMOVAL .................5-55
PULLEY - DESCRIPTION, GENERATOR DECOUPLER ........................ 8F-28PULLEY - DIAGNOSIS AND TESTING,
GENERATOR DECOUPLER ..............8F-28
PULLEY - INSTALLATION, GENERATOR DECOUPLER ........................ 8F-29
PULLEY - INSTALLATION, TIMING BELT TENSIONER .......................... 9-70
PULLEY - OPERATION, GENERATOR DECOUPLER ........................ 8F-28
PULLEY - REMOVAL, GENERATOR DECOUPLER ........................ 8F-29
PULLEY - REMOVAL, TIMING BELT TENSIONER .......................... 9-69
PUMP - 2.4L - CLEANING, WATER ........7-32
PUMP - 2.4L - DESCRIPTION, WATER .....7-32
PUMP - 2.4L - INSPECTION, WATER ......7-32
PUMP - 2.4L - INSTALLATION, WATER .....7-32
PUMP - 2.4L - REMOVAL, WATER ........7-32
PUMP - 3.3/3.8L - CLEANING, WATER .....7-35
PUMP - 3.3/3.8L - DESCRIPTION, WATER ............................. 7-34
PUMP - 3.3/3.8L - INSPECTION, WATER . . . 7-35
PUMP - 3.3/3.8L - INSTALLATION, WATER ............................. 7-35
PUMP - 3.3/3.8L - REMOVAL, WATER .....7-34
PUMP - ASSEMBLY, OIL ...........9-146,9-58
PUMP - ASSEMBLY, OIL ........21-112,21-263
PUMP - CLEANING, OIL ...........9-145,9-57
PUMP - DESCRIPTION, FUEL ............14-8
PUMP - DESCRIPTION, FUEL DOSING . . . 24-117
PUMP - DESCRIPTION, OIL .............9-144
PUMP - DESCRIPTION, OIL ......21-110,21-261
PUMP - DISASSEMBLY, OIL ........9-145,9-57
PUMP - DISASSEMBLY, OIL .....21-110,21-261
PUMP - INSPECTION, OIL ..........9-145,9-58
PUMP - INSTALLATION, FUEL DOSING . . . 24-117
PUMP - INSTALLATION, LEAK DETECTION ......................... 25-15
PUMP - INSTALLATION, OIL ........9-146,9-59
PUMP - INSTALLATION, SEAL - OIL ....21-113,
21-264
PUMP - OPERATION, FUEL ..............14-8
PUMP - OPERATION, FUEL DOSING .....24-117
PUMP - OPERATION, OIL .......21-110,21-261
PUMP - REMOVAL, FUEL DOSING ......24-117
PUMP - REMOVAL, LEAK DETECTION ....25-15
PUMP - REMOVAL, OIL ............9-144,9-56
PUMP - REMOVAL, SEAL - OIL . . . 21-113,21-264
PUMP (2.4L ENGINE) - INSTALLATION ....19-43
PUMP (2.4L ENGINE) - REMOVAL .......19-38
PUMP (2.4L/3.3L/3.8L ENGINE) - DESCRIPTION ....................... 19-36
PUMP (3.3L/3.8L ENGINE) - INSTALLATION ....................... 19-43
PUMP (3.3L/3.8L ENGINE) - REMOVAL . . . 19-40
PUMP (DIESEL) - DESCRIPTION .........19-37
PUMP (DIESEL) - INSTALLATION ........19-43
PUMP (DIESEL) - REMOVAL ............19-41
PUMP INITIAL OPERATION - STANDARD PROCEDURE, POWER STEERING ........19-37
PUMP INLET TUBE - 2.4L - DESCRIPTION, WATER .................7-36
PUMP INLET TUBE - 2.4L - INSTALLATION, WATER .................7-36
PUMP INLET TUBE - 2.4L - REMOVAL, WATER ............................. 7-36
PUMP INLET TUBE - 3.3/3.8L - INSTALLATION, WATER .................7-37
PUMP INLET TUBE - 3.3/3.8L - REMOVAL, WATER .................... 7-37
PUMP MODULE - DESCRIPTION, FUEL ....14-8
PUMP MODULE - OPERATION, FUEL ......14-9
PUMP MOTOR - INSTALLATION, WASHER ........................... 8R-12
PUMP MOTOR - REMOVAL, WASHER ....8R-12
PUMP (PULLEY) - ASSEMBLY ..........19-42
PUMP (PULLEY) - DISASSEMBLY ........19-41
PUMP RELAY - DESCRIPTION, FUEL .....14-32
PUMP RELAY - OPERATION, FUEL .......14-32
PUMP, SPECIAL TOOLS - POWER STEERING .......................... 19-44
PUSH-PIN GROMMET REPLACEMENT, STANDARD PROCEDURE ..............8N-48
PUSHRODS - DESCRIPTION ............9-112
PUSHRODS - OPERATION ..............9-112
QUAD BUCKET - INSTALLATION, BUCKET SEAT BACK ........................ 23-141
QUAD BUCKET - INSTALLATION, SEAT BELT BUCKLE - FIRST ROW INBOARD ....8O-36
24 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

SEAT STORAGE BIN GUIDE - REMOVAL,UNDER ............................ 23-150
SEAT STORAGE BIN LOCK/LATCH - INSTALLATION, UNDER ...............23-150
SEAT STORAGE BIN LOCK/LATCH - REMOVAL, UNDER .................. 23-150
SEAT SWITCH - DESCRIPTION ..........8N-34
SEAT SWITCH - DESCRIPTION, HEATED . . . 8G-8
SEAT SWITCH - OPERATION ............8N-34
SEAT SWITCH - OPERATION, HEATED .....8G-9
SEAT SWITCH, DIAGNOSIS AND TESTING - DRIVER ................... 8N-34
SEAT SWITCH, DIAGNOSIS AND TESTING - DRIVER HEATED .............8G-9
SEAT SYSTEM - DESCRIPTION, HEATED . . . 8G-7
SEAT SYSTEM - OPERATION, HEATED .....8G-8
SEAT SYSTEM, DESCRIPTION - POWER . . 8N-31
SEAT SYSTEM, DIAGNOSIS AND TESTING - HEATED .................... 8G-8
SEAT SYSTEM, DIAGNOSIS AND TESTING - POWER ................... 8N-33
SEAT SYSTEM, OPERATION - POWER ....8N-32
SEAT TRACK - DESCRIPTION, POWER ....8N-37
SEAT TRACK - INSTALLATION, BENCH . . . 23-148
SEAT TRACK - OPERATION, POWER .....8N-38
SEAT TRACK - REAR COVER - INSTALLATION, FRONT ...............23-128
SEAT TRACK - REAR COVER - REMOVAL, FRONT ................... 23-128
SEAT TRACK - REMOVAL, BENCH ........23-148
SEAT TRACK ADJUSTER/MANUAL - OCS - INSTALLATION, FRONT ..............23-128
SEAT TRACK ADJUSTER/MANUAL - OCS - REMOVAL, FRONT .................23-126
SEAT TRACK ADJUSTER/POWER - OCS - INSTALLATION, FRONT ...............23-125
SEAT TRACK ADJUSTER/POWER - OCS - REMOVAL, FRONT ................... 23-124
SEAT TRACK, DIAGNOSIS AND TESTING - POWER ........................... 8N-38
SEAT TRACK MANUAL ADJUSTER - INSTALLATION, FRONT ...............23-126
SEAT TRACK MANUAL ADJUSTER - REMOVAL, FRONT ................... 23-125
SEAT TRACK POWER ADJUSTER - INSTALLATION, FRONT ...............23-124
SEAT TRACK POWER ADJUSTER - REMOVAL, FRONT ................... 23-124
SEAT TRACK REAR COVER - OCS - INSTALLATION, FRONT ...............23-129
SEAT TRACK REAR COVER - OCS - REMOVAL, FRONT ................... 23-129
SEAT WEIGHT BLADDER & PRESSURE SENSOR - DESCRIPTION ..............8O-43
SEAT WEIGHT BLADDER & PRESSURE SENSOR - OPERATION ................8O-44
SEATING - INSTALLATION, FOLD-IN- FLOOR .......................... 5-68,5-75
SEATING - INSTALLATION, FWD - FOLD-IN-FLOOR ....................... 2-45
SEATING - REMOVAL, FOLD-IN-FLOOR . 5-66,5-72
SEATING - REMOVAL, FWD - FOLD-IN- FLOOR .............................. 2-45
SEAT/MIRROR MODULE - DESCRIPTION, MEMORY ............................ 8E-9
SEAT/MIRROR MODULE - OPERATION, MEMORY ............................ 8E-9
SEAT/MIRROR MODULE, DIAGNOSIS AND TESTING - MEMORY ...............8E-9
SEATS - CLEANING, INTAKE/EXHAUST VALVES ........................ 9-108,9-33
SEATS - DESCRIPTION, INTAKE/ EXHAUST VALVES ................ 9-107,9-33
SEATS - INSPECTION, INTAKE/EXHAUST VALVES ............................ 9-108
SEATS - INSTALLATION, INTAKE/ EXHAUST VALVES .................... 9-109
SEATS - OPERATION, INTAKE/EXHAUST VALVES ............................ 9-107
SEATS - REMOVAL, INTAKE/EXHAUST VALVES ............................ 9-108
SEATS - STANDARD PROCEDURE, REFACING VALVES AND VALVE ..........9-107
SEATS ONLY - SPECIFICATIONS, FRAME DIMENSIONS - FOLD-IN-FLOOR .........13-11
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, ARMREST ............23-130SECOND ROW - FOLD-IN-FLOOR -
INSTALLATION, ARMREST ROTATING
ASSEMBLY ......................... 23-130
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, HEADREST SLEEVE .....23-131
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT .................23-132
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACK COVER/
FOAM ............................. 23-133
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACK FRAME .....23-134
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BASE RISER ......23-135
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT CUSHION SIDE
SHIELD ........................... 23-138
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT GAS STRUT ......23-139
SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT PROP ROD .......23-140
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, ARMREST ................23-130
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, ARMREST ROTATING
ASSEMBLY ......................... 23-130
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, HEADREST SLEEVE .........23-131
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT .................... 23-132
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACK COVER/FOAM ....23-133
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACK FRAME .........23-134
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BASE RISER ..........23-134
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT CUSHION SIDE
SHIELD ........................... 23-138
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT GAS STRUT ..........23-138
SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT PROP ROD ...........23-139
SECOND ROW - INSTALLATION, BENCH SEAT RISER ........................ 23-145
SECOND ROW - LEFT OUTBOARD - INSTALLATION, SEAT BELT &
RETRACTOR ........................ 8O-42
SECOND ROW - LEFT OUTBOARD - REMOVAL, SEAT BELT & RETRACTOR ....8O-42
SECOND ROW - REMOVAL, BENCH SEAT RISER ............................ 23-145
SECOND ROW - RIGHT OUTBOARD - INSTALLATION, SEAT BELT &
RETRACTOR ........................ 8O-40
SECOND ROW - RIGHT OUTBOARD - REMOVAL, SEAT BELT & RETRACTOR ....8O-40
SECOND ROW - RIGHT OUTBOARD WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT &
RETRACTOR ........................ 8O-41
SECOND ROW - RIGHT OUTBOARD WITH REAR HVAC - LWB - REMOVAL,
SEAT BELT & RETRACTOR .............8O-41
SECOND ROW - THREE PASSENGER BENCH - INSTALLATION, SEAT BELT
BUCKLE ............................ 8O-40
SECOND ROW - THREE PASSENGER BENCH - REMOVAL, SEAT BELT
BUCKLE ............................ 8O-40
SECOND ROW FLOOR TUB CARPET INSERT - FOLD-IN-FLOOR -
INSTALLATION ....................... 23-98
SECOND ROW FLOOR TUB CARPET INSERT - FOLD-IN-FLOOR - REMOVAL ....23-98
SECOND ROW -FOLD-IN-FLOOR - INSTALLATION, SEAT BACK PANEL ......23-134
SECOND ROW -FOLD-IN-FLOOR - REMOVAL, SEAT BACK PANEL .........23-134
SECOND ROW INBOARD - 50/50 BENCH - INSTALLATION, SEAT BELT BUCKLE ....8O-38
SECOND ROW INBOARD - 50/50 BENCH - REMOVAL, SEAT BELT BUCKLE ........8O-37
SECTION IDENTIFICATION AND INFORMATION - DESCRIPTION ........8W-01-6
SECURITY - DESCRIPTION, VEHICLE THEFT .............................. 8Q-1
SECURITY - OPERATION, VEHICLE THEFT . . 8Q-1SECURITY SYSTEM - DIAGNOSIS AND
TESTING, VEHICLE THEFT ..............8Q-3
SELF-DIAGNOSTICS - DIAGNOSIS AND TESTING ............................ 8J-2
SENDING UNIT / SENSOR - DESCRIPTION, FUEL LEVEL .............14-5
SENDING UNIT / SENSOR - INSTALLATION, FUEL LEVEL .............14-6
SENDING UNIT / SENSOR - OPERATION, FUEL LEVEL .......................... 14-5
SENDING UNIT / SENSOR - REMOVAL, FUEL LEVEL .......................... 14-5
SENSE - PCM INPUT - OPERATION, IGNITION ........................... 8E-14
SENSITIVE DEVICES - STANDARD PROCEDURE, ELECTROSTATIC
DISCHARGE (ESD) .................8W -01-8
SENSOR - 2.4L - DESCRIPTION, ENGINE COOLANT TEMPERATURE ...............7-21
SENSOR - 2.4L - INSTALLATION, ENGINE COOLANT TEMPERATURE ...............7-21
SENSOR - 2.4L - REMOVAL, ENGINE COOLANT TEMPERATURE ...............7-21
SENSOR - 3.3/3.8L - DESCRIPTION, ENGINE COOLANT TEMPERATURE ........7-21
SENSOR - 3.3/3.8L - INSTALLATION, ENGINE COOLANT TEMPERATURE ........7-23
SENSOR - 3.3/3.8L - REMOVAL, ENGINE COOLANT TEMPERATURE ...............7-21
SENSOR - AWD - INSTALLATION, REAR WHEEL SPEED ........................ 5-92
SENSOR - AWD - REMOVAL, REAR WHEEL SPEED ........................ 5-92
SENSOR - DESCRIPTION, AMBIENT TEMP ............................. 8M-12
SENSOR - DESCRIPTION, BATTERY TEMPERATURE ...................... 8F-24
SENSOR - DESCRIPTION, BELT TENSION . . 8O-8
SENSOR - DESCRIPTION, CAMSHAFT POSITION ............................ 8I-4
SENSOR - DESCRIPTION, CRANKSHAFT POSITION .......................... 14-29
SENSOR - DESCRIPTION, ENGINE SPEED . 14-30
SENSOR - DESCRIPTION, EVAPORATOR TEMPERATURE ...................... 24-26
SENSOR - DESCRIPTION, FUEL LEVEL SENDING UNIT ....................... 14-5
SENSOR - DESCRIPTION, HEATED SEAT . . 8G-13
SENSOR - DESCRIPTION, IMPACT .......8O-18
SENSOR - DESCRIPTION, INFRARED TEMPERATURE ...................... 24-28
SENSOR - DESCRIPTION, INLET AIR TEMPERATURE ...................... 14-34
SENSOR - DESCRIPTION, KNOCK .........8I-8
SENSOR - DESCRIPTION, MAP ..........14-34
SENSOR - DESCRIPTION, O2 ...........14-36
SENSOR - DESCRIPTION, PARK ASSIST . . . 8B-6
SENSOR - DESCRIPTION, PINCH ........8N-17
SENSOR - DESCRIPTION, SEAT WEIGHT BLADDER & PRESSURE ...............8O-43
SENSOR - DESCRIPTION, THROTTLE POSITION .......................... 14-40
SENSOR - DESCRIPTION, TRANSMISSION RANGE ........21-130,21-281
SENSOR - DIAGNOSIS AND TESTING, TIRE PRESSURE ..................... 22-11
SENSOR - FWD - INSTALLATION, REAR WHEEL SPEED ........................ 5-93
SENSOR - FWD - REMOVAL, REAR WHEEL SPEED ........................ 5-93
SENSOR - INPUT - DESCRIPTION, SPEED ...................... 21-120,21-271
SENSOR - INPUT - INSTALLATION, SPEED ...................... 21-121,21-272
SENSOR - INPUT - OPERATION, SPEED . 21-120, 21-271
SENSOR - INPUT - REMOVAL, SPEED . . . 21-121, 21-272
SENSOR - INSTALLATION, FRONT WHEEL SPEED ........................ 5-92
SENSOR - INSTALLATION, FUEL LEVEL SENDING UNIT ....................... 14-6
SENSOR - INSTALLATION, IMPACT ......8O-21
SENSOR - INSTALLATION, PARK ASSIST . . . 8B-6
SENSOR - INSTALLATION, PINCH ........8N-18
SENSOR - INSTALLATION, TRANSMISSION RANGE ........21-131,21-282
SENSOR - OPERATION, AMBIENT TEMP . . 8M-12
28 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

SENSOR - OPERATION, BATTERYTEMPERATURE ...................... 8F-24
SENSOR - OPERATION, BELT TENSION ....8O-9
SENSOR - OPERATION, CAMSHAFT POSITION ............................ 8I-4
SENSOR - OPERATION, CRANKSHAFT POSITION .......................... 14-29
SENSOR - OPERATION, ENGINE SPEED . . . 14-30
SENSOR - OPERATION, EVAPORATOR TEMPERATURE ...................... 24-27
SENSOR - OPERATION, FUEL LEVEL SENDING UNIT ....................... 14-5
SENSOR - OPERATION, HEATED SEAT ....8G-13
SENSOR - OPERATION, INFRARED TEMPERATURE ...................... 24-28
SENSOR - OPERATION, KNOCK ...........8I-8
SENSOR - OPERATION, MAP ...........14-34
SENSOR - OPERATION, O2 .............14-36
SENSOR - OPERATION, PARK ASSIST .....8B-6
SENSOR - OPERATION, PINCH ..........8N-17
SENSOR - OPERATION, SEAT WEIGHT BLADDER & PRESSURE ...............8O-44
SENSOR - OPERATION, THROTTLE POSITION .......................... 14-41
SENSOR - OPERATION, TRANSMISSION RANGE ...................... 21-131,21-282
SENSOR - OUTPUT - DESCRIPTION, SPEED ...................... 21-122,21-273
SENSOR - OUTPUT - INSTALLATION, SPEED ...................... 21-123,21-274
SENSOR - OUTPUT - OPERATION, SPEED ...................... 21-122,21-273
SENSOR - OUTPUT - REMOVAL, SPEED . 21-123, 21-274
SENSOR - REMOVAL, BATTERY TEMPERATURE ...................... 8F-24
SENSOR - REMOVAL, CRANKSHAFT POSITION .......................... 14-30
SENSOR - REMOVAL, FRONT WHEEL SPEED .............................. 5-91
SENSOR - REMOVAL, FUEL LEVEL SENDING UNIT ....................... 14-5
SENSOR - REMOVAL, IMPACT ..........8O-19
SENSOR - REMOVAL, PARK ASSIST ......8B-6
SENSOR - REMOVAL, PINCH ...........8N-18
SENSOR - REMOVAL, TRANSMISSION RANGE ...................... 21-131,21-282
SENSOR - SPECIFICATIONS, BATTERY TEMPERATURE ...................... 8F-23
SENSOR - TPM - CAUTION .............22-11
SENSOR - TPM - DESCRIPTION .........22-10
SENSOR - TPM - INSTALLATION ........22-11
SENSOR - TPM - OPERATION ...........22-10
SENSOR - TPM - REMOVAL ............22-11
SENSOR AIR GAP, SPECIFICATIONS - WHEEL SPEED ........................ 5-91
SENSOR CIRCUIT, DIAGNOSIS AND TESTING - AMBIENT TEMPERATURE .....8M-12
SENSOR, DIAGNOSIS AND TESTING - AMBIENT TEMPERATURE ..............8M-12
SENSOR, DIAGNOSIS AND TESTING - HEATED SEAT ....................... 8G-13
SENSOR RETURN - PCM INPUT - OPERATION ......................... 8E-14
SENTRY KEY REMOTE ENTRY MODULE - DESCRIPTION ........................ 8Q-3
SENTRY KEY REMOTE ENTRY MODULE - DIAGNOSIS AND TESTING ..............8Q-5
SENTRY KEY REMOTE ENTRY MODULE - INSTALLATION ....................... 8Q-6
SENTRY KEY REMOTE ENTRY MODULE - OPERATION .......................... 8Q-4
SENTRY KEY REMOTE ENTRY MODULE - REMOVAL ........................... 8Q-6
SENTRY KEY REMOTE ENTRY SYSTEM - DIAGNOSIS AND TESTING ..............8Q-3
SERVO - DESCRIPTION .................8P-4
SERVO - INSTALLATION ................8P-4
SERVO - OPERATION ..................8P-4
SERVO - REMOVAL .................... 8P-4
SETTING - STANDARD PROCEDURE, PINION FACTOR ...................... 8E-15
SETTING TRANSMITTER CODES, STANDARD PROCEDURE ..............8M-12
SEVERAL LOADS - STANDARD PROCEDURE, TESTING FOR A SHORT
TO GROUND ON FUSES POWERING . . . 8W-01-10
SHACKLE - INSTALLATION, SPRING .......2-44 SHACKLE - REMOVAL, SPRING
..........2-44
SHAFT - ASSEMBLY, ROCKER ARMS .....9-113
SHAFT - DIAGNOSIS AND TESTING, HALF ................................3-1
SHAFT - DISASSEMBLY, ROCKER ARMS . . 9-113
SHAFT - FRONT - DESCRIPTION, HALF .....3-1
SHAFT - FRONT - INSTALLATION, HALF .....3-4
SHAFT - FRONT - REMOVAL, HALF ........3-2
SHAFT - FRONT - SPECIFICATIONS, HALF . . . 3-6
SHAFT - INSTALLATION, ROCKER ARMS . . 9-113
SHAFT - REMOVAL, ROCKER ARMS ......9-112
SHAFT - RHD - INSTALLATION, PEDAL TORQUE ............................ 5-44
SHAFT - RHD - REMOVAL, PEDAL TORQUE ............................ 5-44
SHAFTS AND CARRIER ASSEMBLY - DESCRIPTION, BALANCE ................9-71
SHAFTS AND CARRIER ASSEMBLY - INSTALLATION, BALANCE ...............9-73
SHAFTS AND CARRIER ASSEMBLY - OPERATION, BALANCE .................9-71
SHAFTS AND CARRIER ASSEMBLY - REMOVAL, BALANCE ................... 9-71
SHIELD - INSTALLATION, FRONT WHEELHOUSE SPLASH ................23-57
SHIELD - NO CUP HOLDER - INSTALLATION, QUAD BUCKET SEAT
SIDE ............................. 23-143
SHIELD - NO CUP HOLDER - REMOVAL, QUAD BUCKET SEAT SIDE ............23-143
SHIELD - REMOVAL, FRONT WHEELHOUSE SPLASH ................23-57
SHIELD - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, SEAT
CUSHION SIDE ..................... 23-138
SHIELD - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, SEAT CUSHION
SIDE ............................. 23-138
SHIELD CUP HOLDER - FOLD-IN-FLOOR - INSTALLATION, SIDE ...............23-160
SHIELD CUP HOLDER - FOLD-IN-FLOOR - REMOVAL, SIDE ................... 23-160
SHIELD/CUP HOLDER - FLAP AND SPRING ASSEMBLY - INSTALLATION,
QUAD BUCKET SEAT SIDE ............23-151
SHIELD/CUP HOLDER - FLAP AND SPRING ASSEMBLY - REMOVAL, QUAD
BUCKET SEAT SIDE .................. 23-151
SHIELD/CUP HOLDER - INSTALLATION, QUAD BUCKET SEAT SIDE ............23-142
SHIELD/CUP HOLDER - REMOVAL, QUAD BUCKET SEAT SIDE .................. 23-141
SHIELDS - DESCRIPTION, HEAT ..........11-7
SHIELDS - INSTALLATION, HEAT .........11-7
SHIELDS - OPERATION, HEAT ............11-7
SHIELDS - REMOVAL, HEAT .............11-7
SHIFT CABLE - INSTALLATION, GEAR ....21-234
SHIFT CABLE - REMOVAL, GEAR . . 21-233,21-84
SHIFT INTERLOCK SOLENOID - DESCRIPTION ................ 21-113,21-264
SHIFT INTERLOCK SOLENOID - DIAGNOSIS AND TESTING, BRAKE/
TRANSMISSION ............... 21-115,21-266
SHIFT INTERLOCK SOLENOID - INSTALLATION ................ 21-116,21-267
SHIFT INTERLOCK SOLENOID - OPERATION .................. 21-114,21-265
SHIFT INTERLOCK SOLENOID - REMOVAL ................... 21-115,21-266
SHOCK ABSORBER - DESCRIPTION .......2-36
SHOCK ABSORBER - INSTALLATION ......2-38
SHOCK ABSORBER - OPERATION .........2-36
SHOCK ABSORBER - REMOVAL ..........2-36
SHOCK ABSORBER (UPPER BUSHING) - ASSEMBLY .......................... 2-37
SHOCK ABSORBER (UPPER BUSHING) - DISASSEMBLY ........................ 2-37
SHOE LINING - INSPECTION, REAR DRUM BRAKE ........................ 5-22
SHOES - ADJUSTMENT, PARKING BRAKE . . 5-85
SHOES - ADJUSTMENT, REAR DRUM BRAKE .............................. 5-23
SHOES - CLEANING, DISC BRAKE ....5-16,5-18
SHOES - INSPECTION, DISC BRAKE . . . 5-16,5-18
SHOES - INSTALLATION, REAR DISC BRAKE .............................. 5-19
SHOES - INSTALLATION, REAR DRUM BRAKE .............................. 5-22SHOES - PARKING BRAKE -
INSTALLATION ........................ 5-84
SHOES - PARKING BRAKE - REMOVAL ....5-78
SHOES - REMOVAL, REAR DISC BRAKE ....5-17
SHOES - REMOVAL, REAR DRUM BRAKE . . 5-19
SHOES (CONTINENTAL TEVES BRAKES) - INSTALLATION, FRONT DISC BRAKE ......5-16
SHOES (CONTINENTAL TEVES BRAKES) - REMOVAL, FRONT DISC BRAKE ..........5-15
SHOES (TRW BRAKES) - INSTALLATION, FRONT DISC BRAKE ................... 5-17
SHOES (TRW BRAKES) - REMOVAL, FRONT DISC BRAKE ................... 5-15
SHORT TO GROUND - STANDARD PROCEDURE, TESTING FOR A ........8W-01-9
SHORT TO GROUND ON FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A ..........................8W -01-10
SHROUD - LOWER - INSTALLATION ......19-21
SHROUD - LOWER - REMOVAL .........19-21
SHROUD - UPPER - INSTALLATION ......19-22
SHROUD - UPPER - REMOVAL ..........19-22
SHUT DOWN RELAY - DESCRIPTION, AUTO ............................... 8I-3
SHUT DOWN RELAY - OPERATION, AUTO . . . 8I-3
SIDE - INSTALLATION, BODY ...........23-44
SIDE - INSTALLATION, LIFTGATE ........23-44
SIDE - REMOVAL, BODY ...............23-44
SIDE - REMOVAL, LIFTGATE ............23-44
SIDE COVER - INSTALLATION, FRONT SEAT CUSHION ..................... 23-121
SIDE COVER - OCS - INSTALLATION, FRONT SEAT CUSHION ...............23-122
SIDE COVER - OCS - REMOVAL, FRONT SEAT CUSHION ..................... 23-121
SIDE COVER - REMOVAL, FRONT SEAT CUSHION .......................... 23-120
SIDE MOLDINGS - INSTALLATION, BODY . . 23-46
SIDE MOLDINGS - REMOVAL, BODY .....23-45
SIDE SHIELD - NO CUP HOLDER - INSTALLATION, QUAD BUCKET SEAT ....23-143
SIDE SHIELD - NO CUP HOLDER - REMOVAL, QUAD BUCKET SEAT ........23-143
SIDE SHIELD - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT
CUSHION .......................... 23-138
SIDE SHIELD - SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT
CUSHION .......................... 23-138
SIDE SHIELD CUP HOLDER - FOLD-IN- FLOOR - INSTALLATION ..............23-160
SIDE SHIELD CUP HOLDER - FOLD-IN- FLOOR - REMOVAL .................. 23-160
SIDE SHIELD/CUP HOLDER - FLAP AND SPRING ASSEMBLY - INSTALLATION,
QUAD BUCKET SEAT .................23-151
SIDE SHIELD/CUP HOLDER - FLAP AND SPRING ASSEMBLY - REMOVAL, QUAD
BUCKET SEAT ...................... 23-151
SIDE SHIELD/CUP HOLDER - INSTALLATION, QUAD BUCKET SEAT ....23-142
SIDE SHIELD/CUP HOLDER - REMOVAL, QUAD BUCKET SEAT .................23-141
SIDE VIEW MIRROR - INSTALLATION .....23-60
SIDE VIEW MIRROR - REMOVAL ........23-60
SIDEVIEW MIRROR - REMOVAL .........8N-30
SIGNAL LAMP - INSTALLATION, PARK/TURN ......................... 8L-18
SIGNAL LAMP - REMOVAL, PARK/TURN . . 8L-18
SIGNAL SYSTEM - DESCRIPTION, TURN . . 8L-17
SIGNAL SYSTEM - OPERATION, TURN ....8L-17
SILL PLATE - INSTALLATION, LIFTGATE . . . 23-95
SILL PLATE - INSTALLATION, SLIDING DOOR ............................. 23-99
SILL PLATE - REMOVAL, LIFTGATE .......23-94
SILL PLATE - REMOVAL, SLIDING DOOR . . 23-98
SILL TRIM PLATE - INSTALLATION, DOOR ............................. 23-89
SILL TRIM PLATE - REMOVAL, DOOR ....23-89
SINGLE ZONE, DESCRIPTION - MANUAL . . . 24-2
SINGLE ZONE, OPERATION - MANUAL .....24-4
SLEEVE - INSTALLATION, HEADREST ....23-107
SLEEVE - REMOVAL, HEADREST .......23-107
SLEEVE - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, HEADREST ....23-131
SLEEVE - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, HEADREST ........23-131
RS INDEX29
Description Group-Page Description Group-Page Description Group-Page

VTSS/SKIS INDICATOR LAMP -OPERATION .......................... 8Q-8
WARNING - A/C SYSTEM ..............24-66
WARNING - ENGINE COOLING SYSTEM . . . 24-65
WARNING - INSTALLATION ............23-162
WARNING - INSTALLATION .............19-16
WARNING - REMOVAL ...............23-161
WARNING - REMOVAL ................19-11
WARNING - SAFETY PRECAUTIONS AND WARNINGS .......................... 23-1
WARNING - WARNINGS ................8O-5
WARNING - WARNINGS AND CAUTIONS . . 19-10, 19-26
WARNING - WINDSHIELD SAFETY PRECAUTIONS ...................... 23-161
WARNING, CHIME/BUZZER ..............8B-2
WARNING, DESCRIPTION ................5-4
WARNING, DESCRIPTION ..............19-37
WARNING, LAMPS/LIGHTING - EXTERIOR ........................... 8L-3
WARNING, OPERATION ...............24-114
WARNINGS AND CAUTIONS, WARNING . . 19-10, 19-26
WARNINGS, GENERAL ..............8W-01-7
WARNINGS, WARNING .................8O-5
WARNINGS, WARNING - SAFETY PRECAUTIONS ........................ 23-1
WASHER FLUID LEVEL SWITCH - INSTALLATION ...................... 8R-11
WASHER FLUID LEVEL SWITCH - REMOVAL .......................... 8R-11
WASHER HOSES - INSTALLATION .......8R-12
WASHER HOSES - REMOVAL ...........8R-11
WASHER PUMP MOTOR - INSTALLATION . 8R-12
WASHER PUMP MOTOR - REMOVAL .....8R-12
WASHER RESERVOIR - INSTALLATION . . . 8R-13
WASHER RESERVOIR - REMOVAL .......8R-12
WASHER SYSTEM - DIAGNOSIS AND TESTING ............................ 8R-5
WATER CHANNEL - INSTALLATION ......23-174
WATER CHANNEL - REMOVAL .........23-174
WATER LEAKS, DIAGNOSIS AND TESTING ............................ 23-1
WATER PUMP - 2.4L - CLEANING ........7-32
WATER PUMP - 2.4L - DESCRIPTION ......7-32
WATER PUMP - 2.4L - INSPECTION .......7-32
WATER PUMP - 2.4L - INSTALLATION .....7-32
WATER PUMP - 2.4L - REMOVAL .........7-32
WATER PUMP - 3.3/3.8L - CLEANING .....7-35
WATER PUMP - 3.3/3.8L - DESCRIPTION . . . 7-34
WATER PUMP - 3.3/3.8L - INSPECTION ....7-35
WATER PUMP - 3.3/3.8L - INSTALLATION ........................ 7-35
WATER PUMP - 3.3/3.8L - REMOVAL ......7-34
WATER PUMP INLET TUBE - 2.4L - DESCRIPTION ........................ 7-36
WATER PUMP INLET TUBE - 2.4L - INSTALLATION ........................ 7-36
WATER PUMP INLET TUBE - 2.4L - REMOVAL ........................... 7-36
WATER PUMP INLET TUBE - 3.3/3.8L - INSTALLATION ........................ 7-37
WATER PUMP INLET TUBE - 3.3/3.8L - REMOVAL ........................... 7-37
WATERSHIELD - INSTALLATION .........23-21
WATERSHIELD - REMOVAL .............23-21
WEAR - STANDARD PROCEDURE, MEASURING TIMING CHAIN ............9-155
WEAR INDICATORS - DIAGNOSIS AND TESTING, TREAD ..................... 22-16
WEAR PATTERNS - DIAGNOSIS AND TESTING, TIRE ...................... 22-16
WEATHERSTRIP - INSTALLATION, FRONT DOOR ............................ 23-168
WEATHERSTRIP - INSTALLATION, FRONT DOOR GLASS RUN .................. 23-166
WEATHERSTRIP - INSTALLATION, SLIDING DOOR ..................... 23-168
WEATHERSTRIP - REMOVAL, FRONT DOOR ............................ 23-168
WEATHERSTRIP - REMOVAL, FRONT DOOR GLASS RUN .................. 23-166WEATHERSTRIP - REMOVAL, SLIDING
DOOR ............................ 23-168
WEIGHT BLADDER & PRESSURE SENSOR - DESCRIPTION, SEAT .........8O-43
WEIGHT BLADDER & PRESSURE SENSOR - OPERATION, SEAT ...........8O-44
WELD LOCATIONS - FOLD-IN-FLOOR - SPECIFICATIONS .................... 23-350
WELD LOCATIONS - SPECIFICATIONS . . . 23-234
WHEEL - DESCRIPTION ...............22-18
WHEEL - INSPECTION, TONE ............5-94
WHEEL - INSTALLATION, STEERING ......19-24
WHEEL - REMOVAL, STEERING .........19-23
WHEEL ALIGNMENT - DESCRIPTION ......2-47
WHEEL ALIGNMENT - STANDARD PROCEDURE ......................... 2-52
WHEEL ALIGNMENT, SPECIFICATIONS .....2-56
WHEEL AND WHEEL TRIM CARE, CLEANING .......................... 22-19
WHEEL ASSEMBLY (ALUMINUM WHEEL) - INSTALLATION, TIRE .................22-8
WHEEL ASSEMBLY (ALUMINUM WHEEL) - REMOVAL, TIRE ..................... 22-8
WHEEL ASSEMBLY (STEEL WHEEL) - INSTALLATION, TIRE ................... 22-8
WHEEL ASSEMBLY (STEEL WHEEL) - REMOVAL, TIRE ...................... 22-8
WHEEL BALANCE - STANDARD PROCEDURE, TIRE .................... 22-5
WHEEL COVER - DESCRIPTION .........22-19
WHEEL COVER - INSTALLATION ..........22-20
WHEEL COVER - REMOVAL ............22-19
WHEEL CYLINDERS - INSPECTION ........5-62
WHEEL CYLINDERS - INSTALLATION ......5-62
WHEEL CYLINDERS - REMOVAL ..........5-62
WHEEL INSPECTION - DIAGNOSIS AND TESTING ........................... 22-19
WHEEL MATCH MOUNTING - STANDARD PROCEDURE, TIRE .................... 22-7
WHEEL MOUNTING STUDS - FRONT - INSTALLATION ....................... 22-21
WHEEL MOUNTING STUDS - FRONT - REMOVAL .......................... 22-21
WHEEL MOUNTING STUDS - REAR - INSTALLATION ....................... 22-22
WHEEL MOUNTING STUDS - REAR - REMOVAL .......................... 22-22
WHEEL ROTATION - STANDARD PROCEDURE, TIRE .................... 22-7
WHEEL RUNOUT, SPECIFICATIONS - TONE ............................... 5-91
WHEEL, SPECIFICATIONS ..............22-19
WHEEL SPEED SENSOR - AWD - INSTALLATION, REAR .................. 5-92
WHEEL SPEED SENSOR - AWD - REMOVAL, REAR ...................... 5-92
WHEEL SPEED SENSOR - FWD - INSTALLATION, REAR .................. 5-93
WHEEL SPEED SENSOR - FWD - REMOVAL, REAR ...................... 5-93
WHEEL SPEED SENSOR - INSTALLATION, FRONT .................5-92
WHEEL SPEED SENSOR - REMOVAL, FRONT .............................. 5-91
WHEEL SPEED SENSOR AIR GAP, SPECIFICATIONS ...................... 5-91
WHEEL TRIM CARE, CLEANING - WHEEL . . 22-19
WHEEL VIBRATION - DIAGNOSIS AND TESTING, TIRE ....................... 22-1
WHEELHOUSE SPLASH SHIELD - INSTALLATION, FRONT ................23-57
WHEELHOUSE SPLASH SHIELD - REMOVAL, FRONT .................... 23-57
WIND DEFLECTOR - INSTALLATION .....23-174
WIND DEFLECTOR - REMOVAL .........23-174
WIND NOISE, DIAGNOSIS AND TESTING . . . 23-2
WINDOW - INSTALLATION, QUARTER . . . 23-164
WINDOW - REMOVAL, QUARTER .......23-164
WINDOW CRANK - INSTALLATION .......23-21
WINDOW CRANK - REMOVAL ...........23-21
WINDOW DEFOGGER RELAY - DESCRIPTION, REAR .................. 8G-3WINDOW DEFOGGER RELAY -
INSTALLATION, REAR .................. 8G-4
WINDOW DEFOGGER RELAY - OPERATION, REAR .................... 8G-3
WINDOW DEFOGGER RELAY - REMOVAL, REAR ..................... 8G-4
WINDOW DEFOGGER SWITCH - DESCRIPTION, REAR .................. 8G-4
WINDOW DEFOGGER SWITCH - OPERATION, REAR .................... 8G-4
WINDOW MOTOR - REMOVAL ..........8N-62
WINDOW MOTOR, DIAGNOSIS AND TESTING - VENT ..................... 8N-62
WINDOW REGULATOR - MANUAL - INSTALLATION ....................... 23-23
WINDOW REGULATOR - MANUAL - REMOVAL .......................... 23-22
WINDOW REGULATOR - POWER - INSTALLATION ....................... 23-22
WINDOW REGULATOR - POWER - REMOVAL .......................... 23-22
WINDOW SWITCH, DIAGNOSIS AND TESTING ........................... 8N-63
WINDOWS - DESCRIPTION, POWER .....8N-61
WINDOWS - OPERATION, POWER .......8N-61
WINDOWS, DIAGNOSIS AND TESTING - POWER ............................ 8N-61
WINDSHIELD - DESCRIPTION ..........23-161
WINDSHIELD SAFETY PRECAUTIONS, WARNING ......................... 23-161
WIPER ARM - INSTALLATION, REAR .....8R-10
WIPER ARM - REMOVAL, REAR ..........8R-10
WIPER ARM ALIGNMENT - STANDARD PROCEDURE, FRONT .................. 8R-9
WIPER ARMS - INSTALLATION, FRONT ....8R-9
WIPER ARMS - REMOVAL, FRONT ........8R-9
WIPER BLADES - CLEANING ...........8R-13
WIPER BLADES - INSTALLATION ........8R-13
WIPER BLADES - REMOVAL ............8R-13
WIPER LINKAGE - INSTALLATION .......8R-14
WIPER LINKAGE - REMOVAL ...........8R-13
WIPER MODULE - INSTALLATION .......8R-14
WIPER MODULE - REMOVAL ...........8R-14
WIPER MOTOR - INSTALLATION, FRONT . . 8R-10
WIPER MOTOR - INSTALLATION, REAR . . . 8R-10
WIPER MOTOR - REMOVAL, FRONT ......8R-9
WIPER MOTOR - REMOVAL, REAR ......8R-10
WIPER SYSTEM - DIAGNOSIS AND TESTING, FRONT ..................... 8R-2
WIPER SYSTEM - DIAGNOSIS AND TESTING, REAR ...................... 8R-4
WIPERS/WASHERS - DESCRIPTION .......8R-1
WIPERS/WASHERS - OPERATION ........8R-2
WIPER/WASHER SWITCH - DESCRIPTION, REAR .................8R-10
WIPER/WASHER SWITCH - DIAGNOSIS AND TESTING, FRONT .................8R-2
WIPER/WASHER SWITCH - OPERATION, REAR .............................. 8R-11
WIRE SPLICING - STANDARD PROCEDURE .....................8W -01-15
WIRING - INSTALLATION, HEATER ......24-122
WIRING - REMOVAL, HEATER ..........24-122
WIRING DIAGRAMS - DESCRIPTION, HOW TO USE .....................8W -01-1
WIRING HARNESS - DESCRIPTION ......8N-59
WIRING HARNESS - DIAGNOSIS AND TESTING .........................8W -01-7
WIRING HARNESS - INSTALLATION ......8N-59
WIRING HARNESS - OPERATION ........8N-59
WIRING HARNESS - REMOVAL .........8N-59
WIRING/TERMINAL, SPECIAL TOOLS . . 8W-01-10
WORN THREADS - STANDARD PROCEDURE, REPAIR OF DAMAGED
OR............................. 9-10,9-88
ZONE, DESCRIPTION - MANUAL DUAL .....24-2
ZONE, DESCRIPTION - MANUAL SINGLE . . . 24-2
ZONE, DESCRIPTION - MANUAL THREE ....24-2
ZONE, OPERATION - MANUAL DUAL ......24-5
ZONE, OPERATION - MANUAL SINGLE .....24-4
ZONE, OPERATION - MANUAL THREE .....24-5
RS INDEX35
Description Group-Page Description Group-Page Description Group-Page