2005 CHRYSLER CARAVAN horn

(2) Remove the driver airbag mounting screws
(Fig. 40).
(3) Lift the airbag from its mount and disconnect
two airbag squib, speed control and horn connectors
(Fig. 41). Remove driver airbag. Properly store the
driver airbag out of the way. (Refer to 8 - ELECTRI-
CAL/RESTRAINTS - WARNING)(4) Remove the steering wheel retaining bolt (Fig.
42).
(5) Remove damper (Fig. 42).
(6) If equipped, disconnect the remote audio con-
trol switch wiring from the clockspring (Fig. 42).
CAUTION: Do not bump or hammer on steering col-
umn or steering column shaft when removing steer-
ing wheel from steering column shaft.
CAUTION: When installing steering wheel puller
bolts in steering wheel, do not thread bolt into
steering wheel more than a half inch. If the bolts
are threaded into the steering wheel more than a
half inch they will contact and damage the clock-
spring.
(7) While holding the steering wheel firmly in the
straight-aheadposition, remove the steering wheel
from steering column shaft using a steering wheel
puller (Fig. 43).
(8) Remove the puller from the steering wheel.
(9) If the remote audio switches need removed
from the steering wheel, (Refer to 8 - ELECTRICAL/
AUDIO/REMOTE SWITCHES - REMOVAL).
INSTALLATION
(1) If the remote radio switches need to be
installed on the steering wheel, (Refer to 8 - ELEC-
TRICAL/AUDIO/REMOTE SWITCHES - INSTALLA-
TION).
CAUTION: Do not force steering wheel onto steer-
ing column shaft by driving it on. Pull steering
wheel down onto shaft using only the steering
wheel retaining nut.
Fig. 41 Driver Airbag Wiring Connections
1 - DRIVER AIRBAG
2 - SQUIB CONNECTORS
3 - SPEED CONTROL/HORN WIRING CONNECTOR
4 - CLOCKSPRING
Fig. 42 Steering Wheel Mounting
1 - STEERING WHEEL
2 - REMOTE AUDIO CONTROL WIRING CONNECTOR (IF
EQUIPPED)
3 - RETAINING BOLT
4 - DAMPER
Fig. 43 Steering Wheel Removal
1 - STEERING WHEEL
2 - PULLER
19 - 24 COLUMNRS
STEERING WHEEL (Continued)

(2) Feed and route wiring from clockspring
through upper access hole in steering wheel.
(3) Align master serrations in steering wheel with
omitted spline on steering column shaft (at 12 o'clock
position). Slide the steering wheel onto the steering
column shaft by hand (Fig. 42). Use care not to pinch
any wiring.
NOTE: Before installing the damper on the steering
wheel, inspect the damper to ensure the rubber iso-
lator on the damper is not deteriorated or damaged.
If the damper is installed with a damaged isolator, a
buzz, squeak or rattle condition may develop.
(4) Install the damper on the steering wheel (Fig.
42).
(5) Install the steering wheel retaining bolt.
Tighten the steering wheel retaining bolt to 61 N´m
(45 ft. lbs.) torque.(6) If the steering wheel is equipped with remote
audio controls, connect the wiring connector to the
clockspring (Fig. 42).
(7) Connect the airbag squib wiring connectors to
the airbag and the horn and speed control switch
connector to the clockspring (Fig. 41).
(8) Install the driver airbag in the steering wheel
(Fig. 40). Install and tighten the airbag attaching
screws to 10 N´m (90 in. lbs.) torque.
(9) Connect the battery negative (ground) cable to
battery post following special Diagnosis And Testing
procedure. (Refer to 8 - ELECTRICAL/RESTRAINTS
- DIAGNOSIS AND TESTING)
(10) Check operation of all steering wheel mounted
components.
(11) Road test vehicle to ensure proper operation of
steering.
RSCOLUMN19-25
STEERING WHEEL (Continued)

CHIRP PREFERENCE - STANDARDPROCEDURE, HORN .................. 8N-24
CIRCUIT, DIAGNOSIS AND TESTING - AMBIENT TEMPERATURE SENSOR ......8M-12
CIRCUIT FUNCTIONS - DESCRIPTION . . 8W-01-6
CIRCUIT INFORMATION - DESCRIPTION . 8W-01-5
CIRCUIT RESISTANCE TEST - DIAGNOSIS AND TESTING, FEED ........8F-35
CIRCUIT TEST - DIAGNOSIS AND TESTING, CONTROL .................. 8F-33
CIRCUIT TEST - DIAGNOSIS AND TESTING, FEED ...................... 8F-36
CIRCUITS AND VALVES - OPERATION, HYDRAULIC .......................... 5-95
CIRCUITS, DESCRIPTION - NON- MONITORED ......................... 25-5
CLAMP - STANDARD PROCEDURE, HOSES .............................. 14-7
CLAMPS - DESCRIPTION, FUEL LINES/HOSES ........................ 14-7
CLAMPS - DESCRIPTION, HOSE ...........7-1
CLAMPS - OPERATION, HOSE .............7-2
CLASSIFICATION MODULE - DESCRIPTION, OCCUPANT .............8O-25
CLASSIFICATION MODULE - INSTALLATION, OCCUPANT ............8O-26
CLASSIFICATION MODULE - OPERATION, OCCUPANT ......................... 8O-25
CLASSIFICATION MODULE - REMOVAL, OCCUPANT ......................... 8O-26
CLEARANCE - STANDARD PROCEDURE, MEASURING CONNECTING ROD
BEARING ............................ 9-123
CLEARANCE USING PLASTIGAGE - STANDARD PROCEDURE, MEASURING
BEARING ........................ 9-12,9-86
CLOCKSPRING - DESCRIPTION .........8O-10
CLOCKSPRING - INSTALLATION .........8O-12
CLOCKSPRING - OPERATION ...........8O-11
CLOCKSPRING - REMOVAL ............8O-12
CLOCKSPRING CENTERING - STANDARD PROCEDURE ........................ 8O-11
CLUSTER - DESCRIPTION, INSTRUMENT . . . 8J-1
CLUSTER - OPERATION, INSTRUMENT .....8J-1
CLUSTER BEZEL - INSTALLATION ........23-65
CLUSTER BEZEL - REMOVAL ...........23-65
CLUSTER DIAGNOSIS - DIAGNOSIS AND TESTING ............................ 8J-3
CLUSTER ILLUMINATION LAMPS - INSTALLATION ....................... 8L-21
CLUSTER ILLUMINATION LAMPS - REMOVAL .......................... 8L-21
CLUSTER LENS - INSTALLATION ........8J-11
CLUSTER LENS - REMOVAL ............8J-11
CLUTCH AIR PRESSURE TESTS - DIAGNOSIS AND TESTING ........21-153,21-8
CLUTCH ASSEMBLY - ASSEMBLY, INPUT ....................... 21-246,21-95
CLUTCH ASSEMBLY - DISASSEMBLY, INPUT ....................... 21-237,21-86
CLUTCH BREAK-IN, STANDARD PROCEDURE - A/C ................... 24-15
CLUTCH COIL, DIAGNOSIS AND TESTING - A/C COMPRESSOR .................. 24-14
CLUTCH INSPECTION, STANDARD PROCEDURE ........................ 24-15
CLUTCH RELAY - DESCRIPTION, A/C COMPRESSOR ....................... 24-18
CLUTCH RELAY - INSTALLATION, A/C COMPRESSOR ....................... 24-19
CLUTCH RELAY - OPERATION, A/C COMPRESSOR ....................... 24-18
CLUTCH RELAY - REMOVAL, A/C COMPRESSOR ....................... 24-19
CLUTCH/COIL - DESCRIPTION, A/C COMPRESSOR ....................... 24-13
CLUTCH/COIL - OPERATION, A/C COMPRESSOR ....................... 24-13
CLUTCHES - DESCRIPTION, DRIVING . . . 21-219,
21-74
CLUTCHES - DESCRIPTION, HOLDING . . . 21-236,
21-86
CLUTCHES - OPERATION, DRIVING .....21-219,
21-74
CLUTCHES - OPERATION, HOLDING ....21-236,
21-86
COAT/CLEARCOAT FINISH - DESCRIPTION, BASE .................23-101CODE - DESCRIPTION, PAINT
..........23-101
CODE CHARTS - SPECIFICATIONS, COLOR ............................ 23-100
CODES - STANDARD PROCEDURE, OBTAINING DIAGNOSTIC TROUBLE ......8E-15
CODES, STANDARD PROCEDURE - ERASING TRANSMITTER ..............8M-12
CODES, STANDARD PROCEDURE - SETTING TRANSMITTER ..............8M-12
COIL - DESCRIPTION, IGNITION ..........8I-6
COIL - OPERATION, IGNITION ............8I-6
COIL, DIAGNOSIS AND TESTING - A/C COMPRESSOR CLUTCH ...............24-14
COLLAR - INSTALLATION, STRUCTURAL . . . 9-49
COLLAR - REMOVAL, STRUCTURAL .......9-49
COLOR CODE CHARTS - SPECIFICATIONS .................... 23-100
COLUMN - DESCRIPTION, STEERING .....19-10
COLUMN - DIAGNOSIS AND TESTING, STEERING .......................... 19-11
COLUMN COVER - INSTALLATION, LOWER STEERING ................... 23-74
COLUMN COVER - INSTALLATION, OVER STEERING .......................... 23-76
COLUMN COVER - REMOVAL, LOWER STEERING .......................... 23-74
COLUMN COVER - REMOVAL, OVER STEERING .......................... 23-76
COLUMN FASTENER TORQUE, SPECIFICATIONS ..................... 19-17
COMBUSTION PRESSURE LEAKAGE TEST - DIAGNOSIS AND TESTING,
CYLINDER ........................ 9-85,9-9
COMMUNICATION RECEIVE - PCM INPUT - OPERATION, DATA BUS ..............8E-14
COMMUNICATIONS INTERFACE (PCI) BUS, OPERATION - PROGRAMMABLE ....14-25
COMPASS CALIBRATION, STANDARD PROCEDURE ......................... 8M-4
COMPASS DEMAGNETIZING, STANDARD PROCEDURE ......................... 8M-5
COMPASS MINI-TRIP COMPUTER, DIAGNOSIS AND TESTING .............8M-10
COMPASS VARIATION ADJUSTMENT, STANDARD PROCEDURE ...............8M-5
COMPASS/MINI-TRIP COMPUTER - DESCRIPTION ....................... 8M-10
COMPASS/MINI-TRIP COMPUTER - OPERATION ........................ 8M-10
COMPRESSION PRESSURE TEST - DIAGNOSIS AND TESTING, CYLINDER . . 9-85,9-9
COMPRESSOR CLUTCH COIL, DIAGNOSIS AND TESTING - A/ C.........24-14
COMPRESSOR CLUTCH RELAY - DESCRIPTION, A/C ................... 24-18
COMPRESSOR CLUTCH RELAY - INSTALLATION, A/C ................... 24-19
COMPRESSOR CLUTCH RELAY - OPERATION, A/C ..................... 24-18
COMPRESSOR CLUTCH RELAY - REMOVAL, A/C ...................... 24-19
COMPRESSOR CLUTCH/COIL - DESCRIPTION, A/C ................... 24-13
COMPRESSOR CLUTCH/COIL - OPERATION, A/C ..................... 24-13
COMPRESSOR, DESCRIPTION - A/C ......24-72
COMPRESSOR, INSTALLATION - A/C .....24-74
COMPRESSOR MOUNTING BRACKET, 2.4L ENGINE - A/C ..............24-74,24-75
COMPRESSOR NOISE DIAGNOSIS, DIAGNOSIS AND TESTING - A/C .........24-72
COMPRESSOR, OPERATION - A/C ........24-72
COMPRESSOR, REMOVAL - A/C .........24-73
COMPUTER - DESCRIPTION, COMPASS/ MINI-TRIP ......................... 8M-10
COMPUTER - OPERATION, COMPASS/ MINI-TRIP ......................... 8M-10
COMPUTER, DIAGNOSIS AND TESTING - COMPASS MINI-TRIP .................8M-10
CONCENTRATION TESTING - DIAGNOSIS AND TESTING, COOLANT ...............7-19
CONDENSER - DESCRIPTION, A/C .......24-75
CONDENSER - OPERATION, A/C .........24-75
CONDITION CHECK, STANDARD PROCEDURE - FLUID LEVEL ......21-230,21-82
CONDITIONER, DESCRIPTION - HEATER AND AIR ............................ 24-1CONDITIONER, OPERATION - HEATER
AND AIR ............................ 24-4
CONNECT FITTING DISASSEMBLY/ ASSEMBLY - STANDARD PROCEDURE,
TRANSMISSION COOLER LINE QUICK .....7-38
CONNECTING ROD - DESCRIPTION, PISTON ........................ 9-119,9-44
CONNECTING ROD - INSTALLATION, PISTON ............................. 9-45
CONNECTING ROD - REMOVAL, PISTON . . . 9-44
CONNECTING ROD BEARING CLEARANCE - STANDARD
PROCEDURE, MEASURING .............9-123
CONNECTING ROD, FITTING .............9-46
CONNECTING RODS - STANDARD PROCEDURE, FITTING .................9-119
CONNECTOR - DESCRIPTION, DATA LINK . . 8E-6
CONNECTOR - INSTALLATION .......8W-01-11
CONNECTOR - OPERATION, DATA LINK ....8E-6
CONNECTOR - REMOVAL ...........8W-01-11
CONNECTOR, GROUND AND SPLICE INFORMATION - DESCRIPTION ........8W-01-7
CONNECTOR/GROUND/SPLICE LOCATION - DESCRIPTION ....................8W -91-1
CONSOLE - DESCRIPTION, OVERHEAD ....8M-2
CONSOLE - FOLD-IN-FLOOR - INSTALLATION, FLOOR ................23-89
CONSOLE - FOLD-IN-FLOOR - REMOVAL, FLOOR ............................. 23-89
CONSOLE - INSTALLATION, LOWER ......23-73
CONSOLE - REMOVAL, LOWER ..........23-73
CONSOLE BASE TRAY - INSTALLATION, FLOOR ............................. 23-89
CONSOLE BASE TRAY - REMOVAL, FLOOR ............................. 23-89
CONSOLE, DIAGNOSIS AND TESTING - OVERHEAD .......................... 8M-3
CONSOLE KEY LOCK TUMBLER - FOLD-IN-FLOOR - INSTALLATION,
FLOOR ............................. 23-90
CONSOLE KEY LOCK TUMBLER - FOLD-IN-FLOOR - REMOVAL, FLOOR .....23-90
CONSOLE LAMP - INSTALLATION, CENTER ............................ 8L-21
CONSOLE LAMP - REMOVAL, CENTER ....8L-21
CONSOLE LAMP SWITCH - INSTALLATION, CENTER ...............8L-21
CONSOLE LAMP SWITCH - REMOVAL, CENTER ............................ 8L-21
CONSOLE LID LATCH - FOLD-IN-FLOOR - INSTALLATION, FLOOR ................23-90
CONSOLE LID LATCH - FOLD-IN-FLOOR - REMOVAL, FLOOR .................... 23-90
CONSOLE, SPECIAL TOOLS - OVERHEAD . . 8M-7
CONTAINER - DESCRIPTION, COOLANT RECOVERY .......................... 7-20
CONTAINER - INSTALLATION, COOLANT RECOVERY .......................... 7-20
CONTAINER - OPERATION, COOLANT RECOVERY .......................... 7-20
CONTAINER - REMOVAL, COOLANT RECOVERY .......................... 7-20
CONTAMINATION - DIAGNOSIS AND TESTING, BRAKE FLUID ................5-33
CONTINUITY - STANDARD PROCEDURE, TESTING .........................8W -01-9
CONTROL (4 SPEED EATX ONLY) - OPERATION, INTERACTIVE SPEED ........8P-2
CONTROL ARM - DESCRIPTION, LOWER . . . 2-12
CONTROL ARM - INSPECTION, LOWER ....2-14
CONTROL ARM - INSTALLATION, LOWER . . 2-15
CONTROL ARM - OPERATION, LOWER .....2-12
CONTROL ARM - REMOVAL, LOWER ......2-12
CONTROL ARM (REAR BUSHING - HYDRO) - ASSEMBLY, LOWER ...........2-15
CONTROL ARM (REAR BUSHING - HYDRO) - DISASSEMBLY, LOWER ........2-13
CONTROL ARM (REAR BUSHING - STANDARD) - ASSEMBLY, LOWER ........2-14
CONTROL ARM (REAR BUSHING - STANDARD) - DISASSEMBLY, LOWER .....2-13
CONTROL CABLE - INSTALLATION, THROTTLE .......................... 14-40
CONTROL CABLE - REMOVAL, THROTTLE .......................... 14-40
CONTROL CALIBRATION, STANDARD PROCEDURE - A/C-HEATER .............24-19
RS INDEX7
Description Group-Page Description Group-Page Description Group-Page

HCU (HYDRAULIC CONTROL UNIT) -OPERATION ......................... 5-101
HEAD - CLEANING, CYLINDER ......9-103,9-26
HEAD - DESCRIPTION, CYLINDER . . . 9-102,9-25
HEAD - INSPECTION, CYLINDER .....9-104,9-27
HEAD - INSTALLATION, CYLINDER . . . 9-104,9-27
HEAD - REMOVAL, CYLINDER ......9-103,9-26
HEAD COVER - CLEANING, CYLINDER .....9-31
HEAD COVER - INSPECTION, CYLINDER . . . 9-31
HEAD COVER - INSTALLATION, CYLINDER ........................... 9-32
HEAD COVER - LEFT - INSTALLATION, CYLINDER .......................... 9-107
HEAD COVER - LEFT - REMOVAL, CYLINDER .......................... 9-107
HEAD COVER - REMOVAL, CYLINDER .....9-31
HEAD COVER - RIGHT - INSTALLATION, CYLINDER .......................... 9-106
HEAD COVER - RIGHT - REMOVAL, CYLINDER .......................... 9-106
HEAD COVER(S) - DESCRIPTION, CYLINDER .......................... 9-105
HEAD GASKET - DIAGNOSIS AND TESTING, CYLINDER ..............9-102,9-25
HEAD OFF - INSTALLATION, CYLINDER . . . 9-111, 9-33
HEAD OFF - REMOVAL, CYLINDER . . . 9-109,9-33
HEAD ON - INSTALLATION, CYLINDER . . . 9-111, 9-33
HEAD ON - REMOVAL, CYLINDER . . . 9-111,9-33
HEADER TRIM - INSTALLATION, REAR ....23-96
HEADER TRIM - REMOVAL, REAR .......23-96
HEADLAMP - DIAGNOSIS AND TESTING . . 8L-11
HEADLAMP - INSTALLATION ............8L-13
HEADLAMP - REMOVAL ...............8L-12
HEADLAMP SWITCH - DIAGNOSIS AND TESTING ........................... 8L-13
HEADLAMP SWITCH - INSTALLATION ....8L-13
HEADLAMP SWITCH - REMOVAL ........8L-13
HEADLAMP UNIT - EXPORT - INSTALLATION ....................... 8L-17
HEADLAMP UNIT - EXPORT - REMOVAL . . 8L-17
HEADLAMP UNIT - INSTALLATION .......8L-15
HEADLAMP UNIT - REMOVAL ...........8L-15
HEADLAMP UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE .............8L-15
HEADLAMP UNIT ALIGNMENT - STANDARD PROCEDURE ...............8L-14
HEADLINER - INSTALLATION ...........23-92
HEADLINER - REMOVAL ...............23-91
HEADREST - INSTALLATION ...........23-106
HEADREST - REMOVAL ...............23-106
HEADREST SLEEVE - INSTALLATION ....23-107
HEADREST SLEEVE - REMOVAL ........23-107
HEADREST SLEEVE - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION .......23-131
HEADREST SLEEVE - SECOND ROW - FOLD-IN-FLOOR - REMOVAL ...........23-131
HEADREST SLEEVE - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION .......23-153
HEADREST SLEEVE - THIRD ROW - FOLD-IN-FLOOR - REMOVAL ...........23-152
HEAT DUCT - INSTALLATION, REAR FLOOR ............................. 24-63
HEAT DUCT - REMOVAL, REAR FLOOR . . . 24-63
HEAT SHIELDS - DESCRIPTION ..........11-7
HEAT SHIELDS - INSTALLATION ..........11-7
HEAT SHIELDS - OPERATION ............11-7
HEAT SHIELDS - REMOVAL .............11-7
HEAT STAKING - STANDARD PROCEDURE ......................... 23-9
HEATED GLASS - DESCRIPTION ..........8G-1
HEATED GLASS - OPERATION ...........8G-2
HEATED MIRRORS - DESCRIPTION .......8G-6
HEATED MIRRORS - OPERATION .........8G-6
HEATED SEAT ELEMENTS - DESCRIPTION ....................... 8G-11
HEATED SEAT ELEMENTS - OPERATION . . 8G-11
HEATED SEAT ELEMENTS, DIAGNOSIS AND TESTING ....................... 8G-11
HEATED SEAT MODULE - DESCRIPTION ....8E-8
HEATED SEAT MODULE - OPERATION .....8E-8
HEATED SEAT MODULE, DIAGNOSIS AND TESTING ............................ 8E-9
HEATED SEAT SENSOR - DESCRIPTION . . . 8G-13
HEATED SEAT SENSOR - OPERATION ....8G-13
HEATED SEAT SENSOR, DIAGNOSIS AND TESTING ........................... 8G-13HEATED SEAT SWITCH - DESCRIPTION
....8G-8
HEATED SEAT SWITCH - OPERATION ......8G-9
HEATED SEAT SWITCH, DIAGNOSIS AND TESTING - DRIVER .................... 8G-9
HEATED SEAT SYSTEM - DESCRIPTION ....8G-7
HEATED SEAT SYSTEM - OPERATION .....8G-8
HEATED SEAT SYSTEM, DIAGNOSIS AND TESTING ............................ 8G-8
HEATER - DESCRIPTION, CABIN ........24-113
HEATER - DESCRIPTION, ENGINE BLOCK . . . 7-20
HEATER - INSTALLATION, ENGINE BLOCK .............................. 7-21
HEATER - OPERATION, ENGINE BLOCK ....7-20
HEATER - REMOVAL, ENGINE BLOCK ......7-21
HEATER AND AIR CONDITIONER, DESCRIPTION ........................ 24-1
HEATER AND AIR CONDITIONER, OPERATION .......................... 24-4
HEATER CONTROL - DESCRIPTION, A/C . . . 24-19
HEATER CORE - DESCRIPTION ....24-102,24-83
HEATER CORE - OPERATION ......24-102,24-84
HEATER CORE FILLING, STANDARD PROCEDURE - REAR .................24-102
HEATER CORE, INSTALLATION - FRONT . . . 24-86
HEATER CORE, REMOVAL - FRONT ......24-85
HEATER CORE TUBES, INSTALLATION - FRONT ............................. 24-85
HEATER CORE TUBES, REMOVAL - FRONT ............................. 24-84
HEATER, DIAGNOSIS AND TESTING - SUPPLEMENTAL CABIN ...............24-114
HEATER HOSES - INSTALLATION . 24-105,24-119
HEATER HOSES - REMOVAL .....24-104,24-119
HEATER INLET HOSE - INSTALLATION ....24-87
HEATER INLET HOSE - REMOVAL ........24-86
HEATER PERFORMANCE TEST, DIAGNOSIS AND TESTING .............24-10
HEATER PIPES - INSTALLATION ........24-120
HEATER PIPES - REMOVAL ............24-119
HEATER RETURN HOSE - INSTALLATION . . 24-89
HEATER RETURN HOSE - REMOVAL ......24-88
HEATER TESTING - DIAGNOSIS AND TESTING, ENGINE BLOCK ...............7-21
HEATER TUBES, INSTALLATION - UNDERBODY ....................... 24-112
HEATER TUBES, REMOVAL - UNDERBODY ....................... 24-109
HEATER UNIT - INSTALLATION .........24-122
HEATER UNIT - REMOVAL .............24-121
HEATER WIRING - INSTALLATION ......24-122
HEATER WIRING - REMOVAL ..........24-122
HEAVY DUTY, CARGO - INSTALLATION, AWD ............................... 2-36
HEAVY DUTY, CARGO - REMOVAL, AWD . . . 2-36
HEIGHT ADJUSTE R-BORC-PILLAR -
INSTALLATION, SEAT BELT .............8O-38
HEIGHT ADJUSTE R-BORC-PILLAR -
REMOVAL, SEAT BELT ................8O-38
HEIGHT ADJUSTER KNOB - INSTALLATION, SEAT BELT .............8O-38
HEIGHT ADJUSTER KNOB - REMOVAL, SEAT BELT ......................... 8O-38
HEIGHT MEASUREMENT - STANDARD PROCEDURE, CURB ................... 2-55
HIGH AND LOW LIMITS, DESCRIPTION ....25-9
HIGH MOUNTED STOP LAMP - INSTALLATION, CENTER ................8L-6
HIGH MOUNTED STOP LAMP - REMOVAL, CENTER .................... 8L-6
HIGH MOUNTED STOP LAMP UNIT - INSTALLATION, CENTER ................8L-6
HIGH MOUNTED STOP LAMP UNIT - REMOVAL, CENTER .................... 8L-6
HIGH PRESSURE RELIEF VALVE, DESCRIPTION ....................... 24-72
HIGH PRESSURE RELIEF VALVE, OPERATION ......................... 24-72
HIGH SPEED OPERATION - STANDARD PROCEDURE, TIRE PRESSURE ..........22-17
HINGE - INSTALLATION ......23-18,23-40,23-62
HINGE - INSTALLATION, CENTER ........23-24
HINGE - INSTALLATION, LOWER ........23-28
HINGE - INSTALLATION, UPPER .........23-36
HINGE - REMOVAL .........23-17,23-40,23-62
HINGE - REMOVAL, BENCH SEAT BACK . . 23-146
HINGE - REMOVAL, CENTER ............23-24
HINGE - REMOVAL, LOWER ............23-28
HINGE - REMOVAL, UPPER .............23-36HINGE COVERS - QUAD BUCKET, 50/50
SPLIT, BENCH - INSTALLATION, SEAT
BACK ............................. 23-146
HINGE COVERS - QUAD BUCKET, 50/50 SPLIT, BENCH - REMOVAL, SEAT BACK . . 23-146
HOISTING - STANDARD PROCEDURE ......0-24
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-16
HOLDDOWN - REMOVAL, BATTERY ......8F-16
HOLDER - FLAP AND SPRING ASSEMBLY - INSTALLATION, QUAD
BUCKET SEAT SIDE SHIELD/CUP .......23-151
HOLDER - FLAP AND SPRING ASSEMBLY - REMOVAL, QUAD BUCKET
SEAT SIDE SHIELD/CUP ..............23-151
HOLDER - FOLD-IN-FLOOR - INSTALLATION, SIDE SHIELD CUP ......23-160
HOLDER - FOLD-IN-FLOOR - REMOVAL, SIDE SHIELD CUP ................... 23-160
HOLDER - INSTALLATION, CUP .........23-65
HOLDER - INSTALLATION, QUAD BUCKET SEAT SIDE SHIELD - NO CUP . . . 23-143
HOLDER - INSTALLATION, QUAD BUCKET SEAT SIDE SHIELD/CUP .......23-142
HOLDER - REMOVAL, CUP .............23-65
HOLDER - REMOVAL, QUAD BUCKET SEAT SIDE SHIELD - NO CUP ..........23-143
HOLDER - REMOVAL, QUAD BUCKET SEAT SIDE SHIELD/CUP ..............23-141
HOLDING CLUTCHES - DESCRIPTION . . . 21-236, 21-86
HOLDING CLUTCHES - OPERATION .....21-236,
21-86
HONING - STANDARD PROCEDURE, CYLINDER BORE ................. 9-115,9-36
HOOD - INSTALLATION ................23-63
HOOD - REMOVAL .................... 23-62
HOOD AJAR SWITCH - EXPORT - INSTALLATION ....................... 8Q-3
HOOD AJAR SWITCH - EXPORT - REMOVAL ........................... 8Q-3
HORN CHIRP PREFERENCE - STANDARD PROCEDURE ........................ 8N-24
HORN, DIAGNOSIS AND TESTING ........8H-3
HORN SWITCH - DESCRIPTION ..........8H-4
HORN SYSTEM - DESCRIPTION ..........8H-1
HORN SYSTEM - OPERATION ............8H-1
HORN SYSTEM, DIAGNOSIS AND TESTING ............................ 8H-1
HOSE - INSTALLATION, HEATER INLET ....24-87
HOSE - INSTALLATION, HEATER RETURN . 24-89
HOSE - REMOVAL, HEATER INLET .......24-86
HOSE - REMOVAL, HEATER RETURN .....24-88
HOSE CLAMPS - DESCRIPTION ...........7-1
HOSE CLAMPS - OPERATION .............7-2
HOSES - DESCRIPTION, BRAKE TUBES ....5-14
HOSES - INSPECTION, BRAKE TUBES .....5-14
HOSES - INSTALLATION, HEATER . 24-105,24-119
HOSES - INSTALLATION, WASHER .......8R-12
HOSES - OPERATION, BRAKE TUBES ......5-14
HOSES - REMOVAL, HEATER ....24-104,24-119
HOSES - REMOVAL, WASHER ..........8R-11
HOSES AND CLAMP - STANDARD PROCEDURE ......................... 14-7
HOUSING - INSTALLATION, AIR CLEANER ....................... 9-102,9-25
HOUSING - INSTALLATION, HVAC ........24-62
HOUSING - REMOVAL, AIR CLEANER . 9-101,9-25
HOUSING - REMOVAL, HVAC ...........24-60
HOUSING FLUID LEAKAGE - DIAGNOSIS AND TESTING, TORQUE CONVERTER . . . 21-154,
21-9
HUB / BEARING - DESCRIPTION .......2-30,2-5
HUB / BEARING - INSTALLATION ......2-33,2-5
HUB / BEARING - OPERATION ........2-30,2-5
HUB / BEARING - REMOVAL ..........2-31,2-5
HUB AND BEARING - DIAGNOSIS AND TESTING ......................... 2-31,2-5
HVAC - LWB - INSTALLATION, SEAT BELT & RETRACTOR - SECOND ROW -
RIGHT OUTBOARD WITH REAR .........8O-41
HVAC - LWB - REMOVAL, SEAT BELT & RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR ...............8O-41
HVAC HOUSING - INSTALLATION ........24-62
HVAC HOUSING - REMOVAL ............24-60
HVAC LOUVER - INSTALLATION, REAR . . . 23-97
HVAC LOUVER - REMOVAL, REAR .......23-96
16 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

STORAGE BIN GUIDE - INSTALLATION,UNDER SEAT ....................... 23-150
STORAGE BIN GUIDE - REMOVAL, UNDER SEAT ....................... 23-150
STORAGE BIN LOCK/LATCH - INSTALLATION, UNDER SEAT ..........23-150
STORAGE BIN LOCK/LATCH - REMOVAL, UNDER SEAT ....................... 23-150
STRAP - INSTALLATION, CHECK .........23-15
STRAP - INSTALLATION, FRONT SEAT BACK ASSIST ...................... 23-112
STRAP - REMOVAL, CHECK ............23-15
STRAP - REMOVAL, FRONT SEAT BACK ASSIST ........................... 23-112
STRAP - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACKSTOW .....23-158
STRAP - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACKSTOW .........23-158
STRIKER - INSTALLATION, CENTER ......23-28
STRIKER - INSTALLATION, FUEL FILL DOOR BLOCKER LATCH ...............23-53
STRIKER - INSTALLATION, GLOVE BOX LATCH ............................. 23-66
STRIKER - INSTALLATION, HOLD OPEN LATCH ............................. 23-26
STRIKER - INSTALLATION, LATCH . . 23-19,23-42, 23-64
STRIKER - INSTALLATION, REAR LATCH . . 23-29
STRIKER - REMOVAL, CENTER ..........23-28
STRIKER - REMOVAL, FUEL FILL DOOR BLOCKER LATCH ..................... 23-53
STRIKER - REMOVAL, GLOVE BOX LATCH ............................. 23-66
STRIKER - REMOVAL, HOLD OPEN LATCH ............................. 23-26
STRIKER - REMOVAL, LATCH . 23-19,23-41,23-64
STRIKER - REMOVAL, REAR LATCH ......23-29
STRIPPED THREAD REPAIR - STANDARD PROCEDURE, MANIFOLD ..............9-147
STRUCTURAL ADHESIVE LOCATIONS - FOLD-IN-FLOOR ONLY -
SPECIFICATIONS .................... 23-228
STRUCTURAL ADHESIVE LOCATIONS - SPECIFICATIONS .................... 23-218
STRUCTURAL COLLAR - INSTALLATION ....9-49
STRUCTURAL COLLAR - REMOVAL .......9-49
STRUT - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, SEAT GAS .....23-139
STRUT - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, SEAT GAS .........23-138
STRUT ASSEMBLY - ASSEMBLY ..........2-23
STRUT ASSEMBLY - DESCRIPTION .......2-19
STRUT ASSEMBLY - DIAGNOSIS AND TESTING ............................ 2-20
STRUT ASSEMBLY - DISASSEMBLY .......2-21
STRUT ASSEMBLY - INSTALLATION .......2-25
STRUT ASSEMBLY - OPERATION .........2-19
STRUT ASSEMBLY - REMOVAL ...........2-20
STUDS - FRONT - INSTALLATION, WHEEL MOUNTING ................... 22-21
STUDS - FRONT - REMOVAL, WHEEL MOUNTING ......................... 22-21
STUDS - REAR - INSTALLATION, WHEEL MOUNTING ......................... 22-22
STUDS - REAR - REMOVAL, WHEEL MOUNTING ......................... 22-22
SUCTION LINE - INSTALLATION . . . 24-107,24-97
SUCTION LINE - REMOVAL .......24-106,24-96
SUN VISOR - INSTALLATION ...........23-99
SUN VISOR - REMOVAL ...............23-99
SUN VISOR SUPPORT - INSTALLATION . . . 23-99
SUN VISOR SUPPORT - REMOVAL .......23-99
SUNROOF - DESCRIPTION ............23-169
SUNROOF ASSEMBLY - INSTALLATION . . 23-173
SUNROOF ASSEMBLY - REMOVAL ......23-173
SUNROOF DIAGNOSIS AND TESTING, DIAGNOSIS AND TESTING ............23-169
SUNROOF GLASS PANEL ADJUSTMENT, ADJUSTMENTS ..................... 23-173
SUNROOF MOTOR - INSTALLATION .....23-174
SUNROOF MOTOR - REMOVAL .........23-174
SUNROOF SWITCH - INSTALLATION .....23-176
SUNROOF SWITCH - REMOVAL ........23-176
SUNSHADE - INSTALLATION ...........23-173
SUNSHADE - REMOVAL ..............23-173
SUPPLEMENTAL CABIN HEATER, DIAGNOSIS AND TESTING ............24-114SUPPLY - PCM OUTPUT - OPERATION, 5
VOLT .............................. 8E-15
SUPPORT - INSTALLATION, LUMBAR ....23-150
SUPPORT - INSTALLATION, SUN VISOR . . . 23-99
SUPPORT - REMOVAL, LUMBAR .......23-150
SUPPORT - REMOVAL, SUN VISOR ......23-99
SUPPORT CYLINDER - INSTALLATION ....23-43
SUPPORT CYLINDER - REMOVAL ........23-42
SUPPORT PLATE - DRUM BRAKE - INSTALLATION ........................ 5-61
SUPPORT PLATE - DRUM BRAKE - REMOVAL ........................... 5-61
SUPPRESSION COMPONENTS - DESCRIPTION, RADIO NOISE ...........8A-15
SUPPRESSION COMPONENTS - OPERATION, RADIO NOISE .............8A-15
SURFACE PREPARATION - STANDARD PROCEDURE, ENGINE GASKET .......9-11,9-87
SUSPENSION - DESCRIPTION, FRONT ......2-2
SUSPENSION - DESCRIPTION, REAR ......2-26
SUSPENSION - OPERATION, FRONT ........2-2
SUSPENSION AND STEERING - DIAGNOSIS AND TESTING ..............2-50
SUSPENSION FASTENER TORQUE, SPECIFICATIONS - FRONT ................2-3
SUSPENSION FASTENER TORQUE, SPECIFICATIONS - REAR ................2-28
SUSPENSION, SPECIAL TOOLS - FRONT ....2-3
SUSPENSION, SPECIAL TOOLS - REAR ....2-28
SWITCH - DESCRIPTION .................8P-5
SWITCH - DESCRIPTION, B-PILLAR ......8N-52
SWITCH - DESCRIPTION, BRAKE FLUID LEVEL .............................. 5-10
SWITCH - DESCRIPTION, BRAKE LAMP ....8L-4
SWITCH - DESCRIPTION, EXTERIOR HANDLE ........................... 8N-10
SWITCH - DESCRIPTION, FULL OPEN ....8N-11,
8N-52
SWITCH - DESCRIPTION, HEATED SEAT . . . 8G-8
SWITCH - DESCRIPTION, HORN ..........8H-4
SWITCH - DESCRIPTION, MEMORY ......8N-36
SWITCH - DESCRIPTION, OIL PRESSURE . 9-144
SWITCH - DESCRIPTION, REAR WINDOW DEFOGGER .................. 8G-4
SWITCH - DESCRIPTION, REAR WIPER/WASHER ..................... 8R-10
SWITCH - DESCRIPTION, SEAT .........8N-34
SWITCH - DIAGNOSIS AND TESTING, BRAKE LAMP ........................ 8L-4
SWITCH - DIAGNOSIS AND TESTING, FAILED PARK ........................ 8R-2
SWITCH - DIAGNOSIS AND TESTING, FRONT WIPER/WASHER ................8R-2
SWITCH - DIAGNOSIS AND TESTING, HEADLAMP ......................... 8L-13
SWITCH - DIAGNOSIS AND TESTING, MULTI-FUNCTION .................... 8L-18
SWITCH - DIAGNOSIS AND TESTING, TRACTION CONTROL ................... 5-94
SWITCH - EXPORT - DESCRIPTION, DOOR CYLINDER LOCK ...............8N-22
SWITCH - EXPORT - DESCRIPTION, POWER FOLDAWAY MIRROR ...........8N-29
SWITCH - EXPORT - INSTALLATION, HOOD AJAR ......................... 8Q-3
SWITCH - EXPORT - INSTALLATION, POWER FOLDAWAY MIRROR ...........8N-30
SWITCH - EXPORT - OPERATION, DOOR CYLINDER LOCK ..................... 8N-22
SWITCH - EXPORT - OPERATION, POWER FOLDAWAY MIRROR ...........8N-29
SWITCH - EXPORT - REMOVAL, HOOD AJAR ............................... 8Q-3
SWITCH - EXPORT - REMOVAL, POWER FOLDAWAY MIRROR .................. 8N-29
SWITCH - INSTALLATION ...............8P-6
SWITCH - INSTALLATION, ADJUSTABLE PEDALS ............................. 5-11
SWITCH - INSTALLATION, B-PILLAR .....8N-52
SWITCH - INSTALLATION, BRAKE FLUID LEVEL .............................. 5-11
SWITCH - INSTALLATION, BRAKE LAMP . . . 8L-5
SWITCH - INSTALLATION, CENTER CONSOLE LAMP ..................... 8L-21
SWITCH - INSTALLATION, EXTERIOR HANDLE ........................... 8N-10
SWITCH - INSTALLATION, FULL OPEN ....8N-11 SWITCH - INSTALLATION, GLOVE BOX
LAMP .............................. 8L-22
SWITCH - INSTALLATION, HEADLAMP ....8L-13
SWITCH - INSTALLATION, IGNITION ......19-19
SWITCH - INSTALLATION, MULTI- FUNCTION .......................... 8L-18
SWITCH - INSTALLATION, OIL PRESSURE ..................... 9-144,9-56
SWITCH - INSTALLATION, SUNROOF ....23-176
SWITCH - INSTALLATION, TRACTION CONTROL ........................... 5-95
SWITCH - INSTALLATION, WASHER FLUID LEVEL ........................ 8R-11
SWITCH - OPERATION .................8P-5
SWITCH - OPERATION, B-PILLAR ........8N-52
SWITCH - OPERATION, BRAKE FLUID LEVEL .............................. 5-10
SWITCH - OPERATION, BRAKE LAMP ......8L-4
SWITCH - OPERATION, EXTERIOR HANDLE ........................... 8N-10
SWITCH - OPERATION, FULL OPEN . 8N-11,8N-52
SWITCH - OPERATION, HEATED SEAT .....8G-9
SWITCH - OPERATION, MEMORY ........8N-36
SWITCH - OPERATION, OIL PRESSURE . . . 9-144
SWITCH - OPERATION, REAR WINDOW DEFOGGER .......................... 8G-4
SWITCH - OPERATION, REAR WIPER/ WASHER ........................... 8R-11
SWITCH - OPERATION, SEAT ...........8N-34
SWITCH - REMOVAL .................... 8P-5
SWITCH - REMOVAL, ADJUSTABLE PEDALS ............................. 5-11
SWITCH - REMOVAL, B-PILLAR .........8N-52
SWITCH - REMOVAL, BRAKE FLUID LEVEL .............................. 5-11
SWITCH - REMOVAL, BRAKE LAMP .......8L-5
SWITCH - REMOVAL, CENTER CONSOLE LAMP .............................. 8L-21
SWITCH - REMOVAL, EXTERIOR HANDLE . 8N-10
SWITCH - REMOVAL, FULL OPEN .......8N-11
SWITCH - REMOVAL, GLOVE BOX LAMP . . 8L-22
SWITCH - REMOVAL, HEADLAMP ........8L-13
SWITCH - REMOVAL, IGNITION .........19-17
SWITCH - REMOVAL, MULTI-FUNCTION . . . 8L-18
SWITCH - REMOVAL, OIL PRESSURE ....9-144,
9-56
SWITCH - REMOVAL, SUNROOF ........23-176
SWITCH - REMOVAL, TRACTION CONTROL ........................... 5-95
SWITCH - REMOVAL, WASHER FLUID LEVEL ............................. 8R-11
SWITCH ASSY - DESCRIPTION, SOLENOID/PRESSURE ..........21-117,21-268
SWITCH ASSY - INSTALLATION, SOLENOID/PRESSURE ..........21-119,21-270
SWITCH ASSY - OPERATION, SOLENOID/ PRESSURE .................. 21-118,21-268
SWITCH ASSY - REMOVAL, SOLENOID/ PRESSURE .................. 21-118,21-269
SWITCH, DIAGNOSIS AND TESTING - DOOR LOCK ........................ 8N-23
SWITCH, DIAGNOSIS AND TESTING - DRIVER HEATED SEAT .................8G-9
SWITCH, DIAGNOSIS AND TESTING - DRIVER SEAT ....................... 8N-34
SWITCH, DIAGNOSIS AND TESTING - MEMORY ........................... 8N-37
SWITCH, DIAGNOSIS AND TESTING - REMOTE ........................... 8N-30
SWITCH, DIAGNOSIS AND TESTING - WINDOW ........................... 8N-63
SWITCH, EXPORT - DOOR CYLINDER LOCK .............................. 8N-22
SWITCHES - DESCRIPTION, REMOTE .....8A-16
SWITCHES - OPERATION, REMOTE ......8A-16
SWITCHES, DIAGNOSIS AND TESTING - REMOTE ........................... 8A-16
SYMBOLS - DESCRIPTION, INTERNATIONAL .......................0-1
SYNCHRONIZING CABLE ADJUSTMENT, INSTALLATION ................ 23-105,23-147
TAIL LAMP - INSTALLATION ............8L-19
TAIL LAMP - REMOVAL ................8L-18
TAIL LAMP UNIT - INSTALLATION .......8L-19
TAIL LAMP UNIT - REMOVAL ...........8L-19
TANK - DESCRIPTION, FUEL ............14-12
TANK - OPERATION, FUEL ..............14-12
RS INDEX31
Description Group-Page Description Group-Page Description Group-Page