2005 CHEVROLET AVALANCHE lock

Then, without shutting off the engine, follow these steps:
The transmission dipstick
handle with this graphic is
located at the rear of
the engine compartment,
on the passenger’s
side of the vehicle.
SeeEngine Compartment Overview on page 5-12for
more information on location.
1. Flip the handle up and then pull out the dipstick
and wipe it with a clean rag or paper towel.
2. Push it back in all the way, wait three seconds and
then pull it back out again.3. Check both sides of the dipstick, and read the lower
level. The uid level must be in the COLD area,
below the cross-hatched area, for a cold check or in
the HOT or cross-hatched area for a hot check.
Be sure to keep the dipstick pointed down to get an
accurate reading.
4. If the uid level is in the acceptable range, push the
dipstick back in all the way; then ip the handle
down to lock the dipstick in place.
5-24

Consistency of Readings
Always check the uid level at least twice using the
procedure described previously. Consistency (repeatable
readings) is important to maintaining proper uid level.
If inconsistent readings persist, check the transmission
breather hose to be sure it is clean and unclogged.
If readings are still inconsistent, contact your dealer.
How to Add Automatic Transmission
Fluid
Refer to the Maintenance Schedule to determine what
kind of transmission uid to use. SeeRecommended
Fluids and Lubricants on page 6-13.
Add uid only after checking the transmission uid while
it is hot. A cold check is used only as a reference.
If the uid level is low, add only enough of the proper
uid to bring the level up to the HOT area for a hot
check. It does not take much uid, generally less than
one pint (0.5 L). Do not overll.Notice:Use of the incorrect automatic transmission
uid may damage your vehicle, and the damages
may not be covered by your warranty. Always
use the automatic transmission uid listed in
Recommended Fluids and Lubricants on page 6-13.
After adding uid, recheck the uid level as
described under “How to Check Automatic
Transmission Fluid,” earlier in this section.
When the correct uid level is obtained, push the
dipstick back in all the way; then ip the handle
down to lock the dipstick in place.
Engine Coolant
The cooling system in your vehicle is lled with
DEX-COOL®engine coolant. This coolant is designed
to remain in your vehicle for ve years or 150,000 miles
(240 000 km), whichever occurs rst, if you add only
DEX-COOL
®extended life coolant.
The following explains your cooling system and how to
add coolant when it is low. If you have a problem
with engine overheating, seeEngine Overheating on
page 5-28.
5-25

{CAUTION:
You can be burned if you spill coolant on hot
engine parts. Coolant contains ethylene glycol
and it will burn if the engine parts are hot
enough. Do not spill coolant on a hot engine.1. You can remove the coolant surge tank pressure
cap when the cooling system, including the coolant
surge tank pressure cap and upper radiator
hose, is no longer hot. Turn the pressure cap slowly
counterclockwise about one full turn.
If you hear a hiss, wait for that to stop. A hiss
means there is still some pressure left.
2. Then keep turning the pressure cap slowly, and
remove it.
3. Fill the coolant surge tank with the proper mixture,
to the FULL COLD mark.
5-34

4. Pull the pins away from their clips and pull them up
until they completely release from the vehicle.
5. Pull the headlamp assembly out of the vehicle.A. Low-Beam Headlamp
B. High-Beam Headlamp
6. Turn the bulb connector counterclockwise and
pull it out of the assembly.
7. Unplug the electrical connector from the old bulb.
8. Plug in the electrical connector to the new bulb.
9. Place the connector with the new bulb into the
headlamp assembly and turn it clockwise until
it is tight.
10. Put the headlamp assembly back into the vehicle
and reinstall the two pins.
11. Place the inboard end of the turn signal/parking
lamp assembly into the pocket.
12. Push the outboard side of the assembly in
until the release clip snaps into place.
5-51

Vehicles without Body-Side Cladding
To replace a headlamp bulb, do the following:
1. Open the hood. SeeHood Release on page 5-10
for more information.
2. Remove the pin on the headlamp assembly by
turning the pin up and pulling it straight out.
3. Pull the headlamp assembly out.A. Low-Beam Headlamp
B. High-Beam Headlamp
4. Unplug the electrical connector.
5. Turn the old bulb counterclockwise and remove it
from the headlamp assembly.
6. Put the new bulb into the assembly and turn it
clockwise until it is tight.
7. Plug in the electrical connector.
8. Reinstall the headlamp assembly.
9. Install the pin and turn it into the locking feature.
5-52

Front Turn Signal, Sidemarker and
Parking Lamps
Vehicles with Body-Side Cladding
To replace a front turn signal, sidemarker, or parking
lamp bulb, do the following:
1. Open the hood. SeeHood Release on page 5-10
for more information.
2. Remove the turn
signal/parking lamp
assembly by pressing
the release clip on the
outboard side of the
assembly and pulling
the outboard end of the
assembly toward you.
3. Pull the inboard side of the assembly out from
the vehicle.A. Sidemarker Lamp
B. Front Turn Signal/Parking Lamp
4. Press the locking release lever (the sidemarker
lamp does not have a locking release lever), turn
the bulb socket counterclockwise and remove it from
the turn signal/parking lamp assembly.
5. Remove the old bulb from the bulb socket.
5-53

6. Put the new bulb into the bulb socket.
7. Put the bulb socket into the turn signal assembly
and turn it clockwise until it locks (the sidemarker
lamp does not lock into place).
8. Place the inboard end of the turn signal/parking
lamp assembly into the pocket.
9. Push the outboard side of the assembly in until the
release clip snaps into place.
Front Turn Signal, Sidemarker and
Daytime Running Lamps
Vehicles without Body-Side Cladding
To replace a front turn signal, sidemarker, or DRL bulb,
do the following:
1. Remove the headlamp assembly as mentioned
previously. SeeHeadlamps on page 5-50for
more information.2. Press the retainer clip (arrow), located behind the
turn signal assembly, towards the outside of the
vehicle.
5-54

3. Pull the turn signal assembly out from the vehicle.A. Daytime Running Lamp (DRL)
B. Front Turn Signal/Parking Lamp
C. Sidemarker Lamp
4. Press the locking release lever (the sidemarker
lamp does not have a locking release lever), turn
the bulb socket counterclockwise and remove it from
the turn signal assembly.
5-55