2005 BMW 325CI park assist

90Technology for safety and driving convenience
Park Distance Control (PDC)*The conceptPDC assists you when you back into a
parking space. Acoustic signals alert
you to the momentary distance to an
object behind your vehicle. The system
features four ultrasonic sensors
mounted in your rear bumper. The mon-
itoring range for the two corner sensors
extends outward roughly 2 ft/60 cm,
while two centrally located sensors
detect objects at distances of up to
approx. 5 ft/1.50 m.
PDC is a parking aid that can
identify objects if they are
approached slowly, as is generally the
case when parking. Avoid driving
towards objects rapidly; due to underly-
ing physical principles, the system may
otherwise alert you too late for you to
take evasive steps.<
The system starts to operate automati-
cally approx. one second after you shift
into Reverse or move the selector lever
into the R position with the ignition key
in position 2.
Let this short period elapse before
driving backwards.<
PDC is deactivated when you shift back
out of Reverse.
You can have a signal set to con-
firm that the PDC has been acti-
vated. The signal then sounds when
you shift into Reverse or move the
selector lever into the R position. indicated by a tone sounding at various
intervals. As the distance between vehi-
cle and object decreases, the intervals
between the tones become shorter. A
continuous tone indicates the pres-
ence of an object less than 1 ft/30 cm
away.
The warning signal is canceled after
approx. three seconds if the distance to
the object remains constant during this
time – if you are moving parallel to
a wall, for instance.
System malfunctions will be indicated
by a continuous high-pitched tone
when the system is activated the first
time. Please have the problem fixed by
your BMW center.
PDC does not replace the driver's
personal responsibility for evaluat-
ing the distance between the vehicle
and any objects. Always remember that
the sensors can neither detect nor pro-
vide warnings of obstacles located
within their blind angles. This applies
especially in those cases where the
system approaches the physical limits
of ultrasonic measurement, as occurs
with tow bars and trailer couplings, and
in the vicinity of thin or wedge-shaped
objects. Moreover, low objects that
have already been detected – such as a
curb edge – can disappear out of the
detection range of the sensors before a
continuous tone sounds.
Loud sources of sound from outside or
inside the vehicle could drown out the
PDC signal tone.<
Keep the sensors clean and free
of ice or snow in order to ensure
that they will continue to operate effec-
tively.
Do not apply high pressure spray to the
sensors for a prolonged period of time.
Always maintain a distance of more
than 4 in/10 cm.<

111
3. Hold the original control device
approx. 2 to 8 in / 5 to 20 cm away
from memory buttons 1.
The required distance between
the control device and the mem-
ory buttons 1 may vary, depending on
the system of the original control device
in question.<
4. Simultaneously press the command
button of the original control device
and the desired memory button 1 on
the integrated universal remote con-
trol. Indicator lamp 2 starts to flash
slowly. When indicator lamp 2
flashes rapidly, release both but-
tons. If the indicator lamp 2 does not
flash rapidly after approx.
15 seconds, select a different dis-
tance between the two devices
5. To program other original control
devices, repeat steps 3 and 4.
The corresponding memory button 1 is
now programmed with the signal of the
original control device.
The system can be operated from igni-
tion key position 2.
If the system cannot be operated
after repeated attempts at pro-
gramming, check whether the original
control device is equipped with an
alternating-code system. You can either
check the operating instructions of the
original control device for this informa-
tion, or you can press and hold down
the programmed memory button 1 of
the integrated universal remote control.
If indicator lamp 2 of the integrated uni-
versal remote control flashes rapidly for
a brief period and then remains on for
approx. 2 seconds, the original control
device is equipped with an alternating-
code system. In this case, you have to
program the memory buttons 1 as
described below for an alternating-
code control device.<
Programming an alternating-code
control deviceYou will need to follow the operating
instructions of the system in question in
order to program the integrated univer-
sal remote control. Read through the
operating instructions for information
on synchronization. Comply with the
following additional instructions when
you program an alternating-code con-
trol device:
You will find programming easier if
you have the assistance of
another person.<
1. Park the vehicle within range of the
radio remote controlled device
2. Program the integrated universal
remote control as described above in
the section on fixed-code program-
ming
3. Locate the button on the receiver of
the target device, for example on the
drive
4. Press the button on the receiver of
the target device. Once you have
completed step 4, you have approx.
30 seconds to complete step 5
5. Press the programmed memory
button 1 of the integrated universal
remote control three times.
The corresponding memory button 1 is
now programmed with the signal of the
original control device.
Please contact your BMW center
if you have any questions.<
Integrated universal remote control*
OverviewControlsMaintenanceRepairsDataIndex

126
Inclines:
To prevent overheating and, as a
result, diminished braking effec-
tiveness, drive down long or steep
downhill grades in a gear which
requires the least braking. Otherwise,
even light but consistent pedal pres-
sure can lead to high temperatures,
brake wear and possibly even brake
failure.<
The braking power of the engine can be
further enhanced by downshifting the
automatic transmission in manual
mode, if necessary, into first gear. This
helps avoid placing excessive loads on
the brake system.
Do not coast with the clutch
depressed or with the transmis-
sion or selector lever in Neutral. Do not
coast with the engine switched off. Oth-
erwise, the engine provides no braking
effect while the transmission is in idling
position, and there is no power-assist
for braking or steering when the engine
is off.
Floor mats, floor carpets or other
objects must not be in the area near the
brake or accelerator pedal, as this
could impair the movement of the ped-
als.<
Corrosion on the brake rotorsLimited vehicle use, extended periods
with the vehicle parked or in storage,
and operating conditions in which brak-
ing is restricted to gentle, low-pressure
applications will all increase the ten-
dency for corrosion to form on the
rotors and contamination to accumulate
on the brake pads. This occurs because
the minimal pressure which must be
exerted by the pads to clean the rotors
by brake applications is not reached.
If the brake rotors are corroded, they
will tend to respond to braking with a
pulsating effect that even extended
brake applications will fail to cure.
Brake pads
For your own safety: use only
brake pads that BMW has
released for your particular vehicle
model. BMW cannot evaluate non-
approved brake pads to determine if
they are suitable for use, and therefore
cannot ensure the operating safety of
the vehicle if they are installed.<
Portable phone in the vehicle
BMW advises against using
mobile equipment, e.g. cellular
phones, inside the vehicle without con-
necting them directly to an outside
antenna. Otherwise, it cannot be ruled
out that vehicle electronics and the
mobile equipment interfere with one
another. In addition, it is not ensured
that the radio waves emitted during
transmission are directed outside of the
vehicle interior.<
General driving notes

163
Mobile Service*To establish contact with the BMW
Group's Mobile Service:
Press button 2 for at least 2 seconds.
The indicator lamp above the buttons
lights up. As soon as a telephone con-
nection has been set up with the Mobile
Service, the indicator lamp flashes.
Depending on the country you are in,
your vehicle's current location will also
be transmitted if your vehicle is
equipped with an activated BMW Assist
function.
Jump-startingWhen your battery is discharged you
can use two jumper cables to start your
vehicle with power from the battery in a
second vehicle. You can also use the
same method to help start another
vehicle. Only use jumper cables with
fully insulated handles on the terminal
clamps.
Do not touch high-voltage wiring
and cables on a running engine.
Contact with components carrying high
voltage can be harmful or fatal. Care-
fully observe the following instructions
to avoid personal injury and/or damage
to one or both vehicles. support vehicle has 12 volts and
approximately the same capacity –
measured in Ah. This information is
provided on the battery
2. Stop the engine of the support vehi-
cle
3. Switch off all electrical components
in both vehicles.
Make absolutely certain that there
is no contact between the body-
work of the two vehicles, otherwise
there is a short circuit hazard.<
Connecting the jumper cables
Always adhere to this sequence
when connecting jumper cables;
failure to observe this procedure can
lead to sparks at the battery terminals
and pose an injury hazard.<
The auxiliary jump-starting terminal
located in your BMW's engine compart-
ment acts as the positive battery termi-
nal. Refer to the engine compartment
overview on page, 140. The cover of
this auxiliary terminal is marked with
a +.
1. Open the cover of the BMW auxiliary
jump-starting terminal. Do so by pull-
ing the tab – see arrow 1
Receiving assistance
OverviewControlsMaintenanceRepairsDataIndex

Everything from A to ZFlat tire 157
Flat Tire Monitor 92
space-saver spare tire 157
Flat Tire Monitor 92
indicator lamp 18, 19, 93
Fluid reservoir for washer
systems 142
Fog lamps
indicator lamp 20
Follow me home lamps 95
Footbrake, refer to Braking
safely 125
Front airbags 59
Front fog lamps 97
Front seat adjustment 51
Fuel
display 85
quality 24
volume 173
Fuel consumption
display 89
Fuel display, refer to Fuel
gauge 85
Fuel economy, refer to
Energy control 84
Fuel filler door 23
release following an elec-
trical malfunction 23
Fuel level indicator, refer to
Fuel gauge 85
Fuel reserve indicator, refer
to Fuel gauge 85Fuel tank capacity 173
Fully-automatic convertible
top 44
activation 44
convenience operation
30, 31
opening, closing 45
remote control 30
Fuses 161
G
Garage door opener, refer to
Integrated universal
remote control 110
Gasoline consumption, refer
to Average fuel consump-
tion 89
Gasoline, refer to Fuel spec-
ifications 24
Gear indicator 75, 79
Gear lever
automatic transmission
with Steptronic 77
sequential manual gear-
box SMG 73
Gearbox
manual transmission 72
Gearshift lever
manual transmission 72
General driving notes 125
Glove compartment 109Grills, refer to Ventilation
100, 104
Gross weight, refer to
Weights 172
H
Handbrake, refer to Parking
brake 71
Hands-free system 113
Hardtop 127
Hardtop preparation 127
Hardtop, refer to the sepa-
rate Owner's Manual 127
Hazard warning flashers 14
Hazard warning triangle 22
Head restraints 52
Headlamp cleaning system
cleaning headlamps 82
washer fluid 142, 173
Headlamp control, auto-
matic 95
Headlamp flasher 97
indicator lamp 20
Headlamps
bulb replacement 153
care, refer to the Caring
for your vehicle brochure
Heated mirrors 57
Heated rear window
air conditioning 102
automatic climate
control 107Heated seats 57
Heating
exterior mirrors 57
rear window 102, 107
seats 57
Heating and ventilation
100, 104
Heavy loads, refer to Cargo
loading 118
Height adjustment
seats 51
steering wheel 58
Height, refer to
Dimensions 171
High beams 80, 81, 97
bulb replacement 154
headlamp flasher 97
indicator lamp 20
Holder for beverages 113
Hood release 138
Horn 14
Hub cap 158
Hydraulic brake assistant,
refer to DBC 127
Hydroplaning 125
I
Ice warning 88
Ignition 69
Ignition key 28
positions 69
Ignition lock 69

Everything from A to Z
183
Outside temperature dis-
play 88
changing unit of
measure 88
P
Paintwork care, refer to the
Caring for your vehicle
brochure
Panic mode, trigger
alarm 30
Park Distance Control
(PDC) 90
Parking aid, refer to Park
Distance Control (PDC) 90
Parking brake 71
indicator lamp 18
Parking lamps 95
bulb replacement 154
Parking lamps/Low
beams 95
Parts and accessories, refer
to Your individual vehicle 5
Passenger-side exterior mir-
ror tilt function 56
PDC Park Distance
Control 90
Placing a telephone call,
refer to the Owner's Man-
ual for the telephone
Plastic, refer to the Caring
for your vehicle brochurePollen, refer to
Microfilter 103
Pollen, refer to Microfil-
ter/activated-charcoal fil-
ter 108
Power output, refer to
Engine data 170
Power seat 51
Power socket 114
Power socket, cigarette
lighter 114
Pressure monitoring, tires
Flat Tire Monitor 92
Pressure, tires 130
Protective function
electric power windows 38
R
Radio remote control key,
refer to Master keys with
remote control 28
Radio, refer to the Owner's
Manual for Radio
Rain sensor 81
Raising the floor panel 35
Range 89
Reading lamps
front 98
hardtop 127
rear 98Rear lamps
bulb replacement 155
indicator lamp, defective
lamp 86
Rear window defroster
air conditioning 102
Rear window heating
automatic climate
control 107
Rear-entry assist 53
Rearview mirror 57
Receiving assistance 162
Recirculated-air mode
air conditioning 102
automatic climate
control 107
Recirculating the air, refer to
Recirculated-air mode
102, 107
Reclining seat, refer to Seat
adjustment 51
Refueling 23
fuel filler door 23
Releasing
hood 138
Remaining distance to ser-
vice 86
Remaining distance, refer to
Range 89Remote control 29
garage door opener 110
luggage compartment
lid 30
malfunction 30
Replacement key 29
Replacing lamps, refer to
Lamps and bulbs 153
Reporting safety defects 7
Restraint systems
for children 62
Restraint systems, refer to
Safety belts 54
Reverse
automatic transmission
with Steptronic 77
SMG gearbox 74
Reverse gear
manual transmission 72
Rollover protection system
66
indicator lamp 19
lowering 66
Roof load capacity 172
Roof-mounted luggage
rack 120
Rope, refer to Towing the
vehicle 165
Run Flat tires 135
S
Safe seating position 50
OverviewControlsMaintenanceRepairsDataIndex