2005 Acura RSX ECU

Many states and Canadian provinces
require special outside mirrors when
towing a trailer. Even if they don’t,
you should install special mirrors if
you cannot clearly see behind you, or
if the trailer creates a blind spot.
Askyourtrailersalesorrental
agency if any other items are
recommended or required f or your
towing situation.The added weight, length, and
height of a trailer will af f ect your
vehicle’s handling and perf ormance,
so driving with a trailer requires
some special driving skills and
techniques.
Foryoursafetyandthesafetyof
others, take time to practice driving
maneuvers bef ore heading f or the
open road, and f ollow the guidelines
discussed below.
Driveslowerthannormalinall
driving situations, and obey posted
speed limits f or vehicles with trailers.
If you have an automatic
transmission, use D position when
towing a trailer on level roads.
When preparing to tow, and bef ore
driving away, be sure to check the
f ollowing:
The vehicle has been properly
serviced, and the tires, brakes,
suspension, cooling system, and
lights are in good operating
condition.
All weights and loads are within
limits.
Thehitch,safetychains,andany
other attachments are secure.
All items in or on the trailer are
properly secured and cannot shif t
while you drive.
Your vehicle tires and spare are
properly inf lated, and the trailer
tires and spare are inflated as
recommended by the trailer
maker.
CONT INUED
Towing a Trailer
A ddit ional T owing Equipment
T owing Speeds and GearsDriving Saf ely With a T railer
Pre-T ow Checklist
Driving
151

Make sure the API Certif ication Seal
says ‘‘For Gasoline Engines’’.
Oil is major contributor to your
engine’s perf ormance and longevity.
Always use a premium-grade
detergent oil displaying the API
Certif ication Seal. This seal indicates
the oil is energy conserving, and that
it meets the American Petroleum
Institute’s latest requirements. It is
highly recommended that you use
Honda motor oil in your vehicle.
Unscrew and remove the engine oil
fill cap on top of the valve cover.
Pour in the oil slowly and caref ully so
you do not spill. Clean up any spills
immediately. Spilled oil could
damage components in the engine
compartment.
Install the engine oil f ill cap, and
tighten it securely. Wait a f ew
minutes, and recheck the oil level.
Do not f ill above the upper mark; you
could damage the engine. The oil’s viscosity or weight is
provided on the container’s label.
5W-20 oil is f ormulated f or year-
round protection of your vehicle, to
improve cold weather starting and
f uel economy.
RSX and Premium models
A dding Engine Oil
Recommended Oil
162
ENGINE OIL FILL CAP
API CERTIFICATION SEAL Ambient Temperature

To thoroughly f lush the transmission,
the technician should drain and ref ill
it with Honda ATF-Z1, then drive the
vehicle f or a short distance. Do this
three times. Then drain and ref ill the
transmission a f inal time.Insert the dipstick all the way back
into the transmission securely as
shown in the illustration.
The transmission should be drained
and ref illed with new f luid according
to the time and distance recommen-
dations in the maintenance schedule.
If youarenotsurehowtoaddfluid,
contact your dealer.
If the level is below the lower
mark, remove the f ill plug and add
f luid to bring it to the upper mark.
Pour the f luid slowly and caref ully
so you do not spill. Clean up any
spill immediately; it could damage
components in the engine
compartment.
Always use Honda ATF-Z1
(Automatic Transmission Fluid). If
it’s not available, you may use a
DEXRON
III automatic
transmission f luid as a temporary
replacement. However, continued
use can affect the shift quality. Have
the transmission f lushed and ref illed
with Honda ATF-Z1 as soon as it is
convenient.
Insert the dipstick all the way into
the transmission securely.
Remove the dipstick and check
the f luid level. It should be
between the upper and lower
marks. 6.
5.
3.
4.
Automatic Transmission Fluid
168
UPPER
MARK
LOWER
MARK

Insert the new bulb into the hole,
making sure the tabs are in their
slots. Pivot the hold-down wire
back in place, and clip the end into
the slot.
Install the rubber seal and make
sure it is right side up; it is marked
‘‘TOP.’’
Pull the battery back to its original
position, then install the bolt in the
hold-down, and tighten it securely. Push the electrical connector onto
the tabs of the new bulb. Make
sureitlocksinplace.Turnonthe
headlights to test the new bulb.
Install the neck of the windshield
washer reservoir on the bracket.
Then remove the bolt f rom the
battery hold-down, and caref ully
push the battery toward the
windshield to obtain enough
working space.
Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way, and remove the bulb. Remove the rubber weather seal
by pulling on the tab. Remove the electrical connector
f rom the bulb by pulling the
connector straight back.
3.
4. 5.
6.
7.
8.
2.
Lights
Driver’s Side
Maint enance
173
HOLD DOWN
WIRE
BULB
WEATHER SEAL
CONNECTOR

Tighten the wheel nuts securely in
the same crisscross pattern. Have
the wheel nut torque checked at
the nearest automotive service
f acility.
Tighten the wheel nuts to:
Put on the spare tire. Put the
wheel nuts back on f inger-tight,
then tighten them in a crisscross
pattern with the wheel nut wrench
until the wheel is f irmly against
the hub. Do not try to tighten
them f ully.
Lower the vehicle to the ground
and remove the jack.
15.
13.
14.
Changing a Flat T ire
196
(Except Type-S)
80 lbf·ft (108 N·m , 11 kgf·m)

Store the jack in its holder. Turn
the jack’s end bracket clockwise to
raisethejackandlockitinplace.
Screw the adapter into the hole in
the spare tire well.Remove the wheel cover or center
cap and place the flat tire face
down in the spare tire well.
Set the bass speaker inside the
wheel.
Secure the f lat tire with the wing
bolt.
Remove the spacer cone f rom the
wing bolt, turn it over, and put it
back on the bolt.
18.
16.
17. 20.
21.
Type-S only: Type-S only:
19.All except Type-S:
CONT INUED
Changing a Flat T ire
T aking Care of t he Unexpect ed
197
ADAPTER (Type-S only) WING BOLTSPACER
CONE

Store the tool kit.
Store the wheel cover or center
cap in the cargo area. Make sure it
will not get scratched or damaged.Diagnosing why the engine won’t
start f alls into two areas, depending
on what you hear when you turn the
key to START (III):
You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
f aster than normal, but the engine
does not start up and run. When you turn the ignition switch to
START (III), you do not hear the
normal noise of the engine trying to
start. You may hear a clicking sound
or series of clicks, or nothing at all.
Check these things:
Check the transmission interlock.
If you have a manual transmission,
the clutch pedal must be pushed
all the way to the f loor or the
starter will not operate. With an
automatic transmission, it must be
in Park or Neutral.
Turn the ignition switch to ON (II).
Turn on the headlights, and check
their brightness. If the headlights
areverydimordonotcomeonat
all, the battery is discharged. See on page .
Reinstall the f loor mat and spare
tire cover, then close the hatch.
22.
23.
24.
200
Changing a Flat Tire, If the Engine Won’t Start
If the Engine Won’t StartNothing Happens or the Starter
Motor Operates Very Slowly
Jump Starting
198
Loose items can fly around the
interior in a crash and could
seriously injure the occupants.
Store the wheel, jack, and tools
securely before driving.

µµ
µ
No. Amps. Circuits Protected
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21 25 30 A
10 A
7.5 A 20 A
10 A
20 A
15 A
20 A
7.5 A 30 A
40 A
40 A
40 A
30 A
20 A
15 A
20 A
100 A 40 A Condenser f an
Small Light
Interior Light
Cooling Fan
Hazard
FI ECU (ECM/PCM)
Horn, Stop
ABS (F/S)
Back Up
ABS Motor
Rear Demister
Heater Motor
Power Window
Option
Lef t Headlight
Door Lock
Right Headlight
Not Used
Main Fuse Battery
Main Fuse Ignition
Spare Fuse
Fuse Locations
212
UNDER HOOD FUSE BOX