2004 YAMAHA YZF-R1SC wheel

3-49
ADJUSTING THE DRIVE CHAIN SLACK
CHK
ADJ
NOTE:
CAUTION:
WARNING
NOTE:
EAS00140
ADJUSTING THE DRIVE CHAIN SLACK
The drive chain slack must be checked at the
tightest point on the chain.
A drive chain that is too tight will overload
the engine and other vital parts, and one that
is too loose can skip and damage the swin-
garm or cause an accident. Therefore, keep
the drive chain slack within the specified
limits.
1. Stand the motorcycle on a level surface.
Securely support the motorcycle so that
there is no danger of it falling over.
Place the motorcycle on a suitable stand so that
the rear wheel is elevated.
2. Spin the rear wheel several times and find
the tightest position of drive chain.
3. Check:

drive chain slack
a
Out of specification
Adjust.
Drive chain slack
25
35 mm (0.98
1.38 in)
4. Adjust:

drive chain slack
a. Loosen the wheel axle nut
1.
b. Loosen both locknuts
2.
c. Turn both adjusting bolts
3 in direction a or
b until the specified drive chain slack is ob-
tained.
ProCarManuals.com

3-50
a
b
ADJUSTING THE DRIVE CHAIN SLACK /
LUBRICATING THE DRIVE CHAINCHK
ADJ
NOTE:
DirectionDrive chain is tightened.
DirectionDrive chain is loosened.
To maintain the proper wheel alignment, adjust
both sides evenly.
d. Tighten both locknuts to specification.
Locknut
16 Nm (1.6 m
kg, 12 ft
lb)
e. Tighten the wheel axle nut to specification.
Wheel axle nut
150 Nm (15 m
kg, 108 ft
lb)
EAS00142
LUBRICATING THE DRIVE CHAIN
The drive chain consists of many interacting
parts. If the drive chain is not maintained proper-
ly, it will wear out quickly. Therefore, the drive
chain should be serviced, especially when the
motorcycle is used in dusty areas.
This motorcycle has a drive chain with small
rubber O-rings between each side plate. Steam
cleaning, high-pressure washing, certain sol-
vents, and the use of a coarse brush can dam-
age these O-rings. Therefore, use only kero-
sene to clean the drive chain. Wipe the drive
chain dry and thoroughly lubricate it with engine
oil or chain lubricant that is suitable for O-ring
chains. Do not use any other lubricants on the
drive chain since they may contain solvents that
could damage the O-rings.
Recommended lubricant
Engine oil or chain lubricant
suitable for O-ring chains
ProCarManuals.com

3-51
CHECKING AND ADJUSTING THE STEERING HEAD
CHK
ADJ
WARNING
NOTE:
NOTE:
EAS00146
CHECKING AND ADJUSTING THE
STEERING HEAD
1. Stand the motorcycle on a level surface.
Securely support the motorcycle so that
there is no danger of it falling over.
Place the motorcycle on a suitable stand so that
the front wheel is elevated.
2. Check:

steering head
Grasp the bottom of the front fork legs and
gently rock the front fork.
Binding / looseness
Adjust the steering
head.
3. Remove:

upper bracket
Refer to “HANDLEBAR” and “STEERING
HEAD” in chapter 4.
4. Adjust:

steering head
a. Remove the lock washer
1, the upper ring
nut
2, and the rubber washer 3.
b. Loosen the lower ring nut
4 and then tighten
it to specification with a steering nut wrench
5.
Set the torque wrench at a right angle to the
steering nut wrench.
Steering nut wrench
90890-01403, YU-33975
Lower ring nut (initial tightening
torque)
52 Nm (5.2 m
kg, 38 ft
lb)
ProCarManuals.com

3-52
CHECKING AND ADJUSTING THE STEERING HEAD
CHK
ADJ
WARNING
NOTE:
NOTE: c. Loosen the lower ring nut
4 completely, then
tighten it to specification.
Do not overtighten the lower ring nut.
Lower ring nut
(final tightening torque)
18 Nm (1.8 m
kg, 13 ft
lb)
d. Check the steering head for looseness or
binding by turning the front fork all the way in
both directions. If any binding is felt, remove
the under bracket and check the upper and
lower bearings.
Refer to “STEERING HEAD” in chapter 4.
e. Install the rubber washer
3.
f. Install the upper ring nut
2.
g. Finger tighten the upper ring nut
2, then
align the slots of both ring nuts. If necessary,
hold the lower ring nut and tighten the upper
ring nut until their slots are aligned.
h. Install the lock washer
1.
Make sure the lock washer tabs
a sit correctly
in the ring nut slots
b.
5. Install:

upper bracket
Refer to “HANDLEBAR” and “STEERING
HEAD” in chapter 4.
6. Measure:

steering head tension
Make sure all of the cables and wires are prop-
erly routed.
a. Point the front wheel straight ahead.
b. Install a plastic locking tie
1 loosely around
the end of the handlebar as shown.
c. Hook a spring gauge
2 onto the plastic lock-
ing tie.
d. Hold the spring gauge at a 90 angle from the
handlebar, pull the spring gauge, and then
record the measurement when the handle-
bar starts to run.
ProCarManuals.com

3-59
AB
CHECKING THE TIRES
CHK
ADJ
WARNING
WARNING
2. Check:

tire surfaces
Damage / wear
Replace the tire.
Minimum tire tread depth
1.6 mm (0.06 in)
1Tire tread depth
2Sidewall
3Wear indicator

Do not use a tubeless tire on a wheel de-
signed only for tube tires to avoid tire fail-
ure and personal injury from sudden defla-
tion.

When using a tube tire, be sure to install the
correct tube.

Always replace a new tube tire and a new
tube as a set.

To avoid pinching the tube, make sure the
wheel rim band and tube are centered in the
wheel groove.

Patching a punctured tube is not recom-
mended. If it is absolutely necessary to do
so, use great care and replace the tube as
soon as possible with a good quality re-
placement.
ATire
BWheel
Tube wheelTube tire only
T beless wheelTube or tubelessTubeless wheeltire
After extensive tests, the tires listed below
have been approved by Yamaha Motor Co.,
Ltd. for this model. The front and rear tires
should always be by the same manufacturer
and of the same design. No guarantee con-
cerning handling characteristics can be giv-
en if a tire combination other than one ap-
proved by Yamaha is used on this
motorcycle.
ProCarManuals.com

3-60
CHECKING THE TIRES / CHECKING THE WHEELS
CHK
ADJ
WARNING
NOTE:
WARNING
NOTE: Front tire
Manufacturer
SizeModel
DUNLOP120 / 70ZR 17
M / C (58W)D218FL
MICHELIN120 / 70ZR 17
M / C (58W)Pilot
POWER C
Rear tire
Manufacturer
SizeModel
DUNLOP190 / 50ZR 17
M / C (73W)D218L
MICHELIN190 / 50ZR 17
M / C (73W)Pilot
POWER G
New tires have a relatively low grip on the
road surface until they have been slightly
worn. Therefore, approximately 100 km
should be traveled at normal speed before
any high-speed riding is done.
For tires with a direction of rotation mark
1:

Install the tire with the mark pointing in the
direction of wheel rotation.

Align the mark
2 with the valve installation
point.
EAS00168
CHECKING THE WHEELS
The following procedure applies to both of the
wheels.
1. Check:

wheel
Damage / out-of-round
Replace.
Never attempt to make any repairs to the
wheel.
After a tire or wheel has been changed or re-
placed, always balance the wheel.
ProCarManuals.com

4-1
4
FRONT WHEEL AND BRAKE DISCSCHAS
Order Job / Part Q’ty Remarks
1
2
3
4
5
6
7
8
9
10Removing the front wheel and brake
discs
Side reflector (left and right)
Brake hose holder (left and right)
Side reflector bracket
Front brake caliper (left and right)
Front wheel axle pinch bolt
Front wheel axle bolt
Front wheel axle
Collar (left and right)
Front wheel
Front brake disc (left and right)2
2
2
2
4
1
1
2
1
2Remove the parts in the order listed.
Place the motorcycle on a suitable stand
so that the front wheel is elevated.
For installation, reverse the removal
procedure.
NOTE:
35 Nm (3.5 m
kg, 25 ft
lb)
6 Nm (0.6 m
kg, 4.3 ft
lb)
91 Nm (9.1 m
kg, 66 ft
lb)
20 Nm (2.0 m
kg, 13 ft
lb)
6 Nm (0.6 m
kg, 4.3 ft
lb)
18 Nm (1.8 m
kg, 13 ft
lb)
2 Nm (0.2 m
kg, 1.4 ft
lb)
2 Nm (0.2 m
kg, 1.4 ft
lb)
EAS00514
CHASSIS
FRONT WHEEL AND BRAKE DISCS
ProCarManuals.com

4-2
FRONT WHEEL AND BRAKE DISCSCHAS
Order Job / Part Q’ty Remarks
Disassembling the front wheel
Oil seal (left and right)
Wheel bearing (left and right)
Spacer2
2
1Disassemble the parts in the order listed.
For assembly, reverse the disassembly
procedure.
1
2
3
EAS00518
ProCarManuals.com