2004 YAMAHA YZF-R1SC display

1-2
1
1 Clock
2 Speedometer
3 “SELECT” button
4 “RESET” button
5 Tachometer
6 Coolant temperature display / air intake
temperature display
7 Odometer / tripmeters / fuel reserve tripme-
ter / stopwatch
8 Shift timing indicator light
1 Clock
2 Speedometer
FEATURES
GEN
INFO
NOTE:
EAS00019
FEATURES
INSTRUMENT FUNCTIONS
Multi-function display
The multi-function meter unit is equipped with
the following:

a speedometer (which shows the riding
speed)

a tachometer (witch shows engine speed)

an odometer (which shows the total distance
traveled)

two tripmeters (which show the distance
traveled since they were last set to zero)

a fuel reserve tripmeter (which shows the
distance traveled since the fuel level warning
light came on)

a stopwatch

a clock

a coolant temperature display

an air intake temperature display

a self-diagnosis device

a display brightness and shift timing indicator
light control mode

Be sure to turn the key to “ON” before using the “SELECT” and “RESET” buttons.
Clock mode
Turn the key to “ON”.
To set the clock
1. Push the “SELECT” button and “RESET”
button together for at least two seconds.
2. When the hour digits start flashing, push the
“RESET” button to set the hours.
3. Push the “SELECT” button, and the minute
digits will start flashing.
4. Push the “RESET” button to set the minutes.
5. Push the “SELECT” button and then release
it to start the clock.
ProCarManuals.com

1-3
FEATURES
GEN
INFO
1 Coolant temperature display / air intake
temperature display
2 Odometer / tripmeters / fuel reserve tripme-
ter / stopwatch
3 Shift timing indicator light
NOTE:
NOTE:Odometer, tripmeter, and stopwatch modes
Push the “SELECT” button to switch the display
between the odometer mode “ODO”, the trip-
meter modes “TRIP A” and “TRIP B” and the
stopwatch mode in the following order:
TRIP A
TRIP B
ODO
Stopwatch

TRIP A
If the fuel level warning light comes on, the
odometer display will automatically change to
the fuel reserve tripmeter mode ”F-TRIP” and
start counting the distance traveled from that
point. In that case, push the ”SELECT” button to
switch the display between the various tripme-
ter, odometer, and stopwatch modes in the fol-
lowing order:
F-TRIP
Stopwatch
TRIP A
TRIP B

ODO
F-TRIP
To reset a tripmeter, select it by pushing the “SE-
LECT” button, and then push the “RESET” button
for at least one second. If you do not reset the fuel
reserve tripmeter manually, it will reset itself auto-
matically and the display will return to the prior
mode after refueling and traveling 5 km (3 mi).
Stopwatch mode
Standard measurement
1. Push the “RESET” button to start the stopwatch.
2. Push the “SELECT” button to stop the stopwatch.
3. Push the “SELECT” button again to reset the stopwatch.
Split-time measurement
1. Push the “RESET” button to start the stopwatch.
2. Push the “RESET” button to measure split-times. (The colon “:” will start flashing.)
3. Push the “RESET” button to display the final split-time or push the “SELECT” button to stop the stop-
watch and display total elapsed time.
4. Push the “SELECT” button to reset the stopwatch.
Coolant temperature display
The coolant temperature display indicates the temperature of the coolant. Push the “RESET” button to
switch the coolant temperature display to the air intake temperature display.
When the coolant temperature display is selected, “C” is displayed before the coolant temperature.
Air intake temperature display
The air intake temperature display indicates the temperature of the air drawn into the air filter case. Push
the “RESET” button to switch the coolant temperature display to the air intake temperature display.

Even if the air intake temperature is set to be displayed, the coolant temperature warning light comes
on when the engine overheats.

When the key is turned to “ON”, the coolant temperature is automatically displayed, even if the air
intake temperature was displayed prior to turning the key to “OFF”.

When the air intake temperature display is selected, “A” is displayed before thetemperature.
ProCarManuals.com

1-4
FEATURES
GEN
INFO
NOTE: Self-diagnosis devices
The model is equipped with a self-diagnosis device for various electrical circuits. If any of those circuits
are defective, the engine trouble warning light will come on, and then the right display will indicate a
two-digit error code (e.g.,11,12,13).
Display brightness and shift timing indicator light control mode
This mode cycles through five control functions, allowing you to make the following settings in the order
listed below.

Display brightness:
This function allows you to adjust the brightness of the displays and tachometer to suit the outside
lighting conditions.

Shift timing indicator light activity:
This function allows you to choose whether or not the indicator light should be activated and whether
it should flash or stay on when activated.

Shift timing indicator light activation:
This function allows you to select the engine speed at which the indicator light will be activated.

Shift timing indicator light deactivation:
This function allows you to select the engine speed at which the indicator light will be deactivated.

Shift timing indicator light brightness:
This function allows you to adjust the brightness of the indicator light to suit your preference.

To make any settings in this mode, you have to cycle through all of its functions. However, if the key is
turned to “OFF” or the engine is started before completing the procedure, only the settings made be-
fore the “SELECT” button was last pushed will be applied.

In this mode, the right display shows the current setting for each function (except the shift timing indi-
cator light activity function).
To adjust the brightness of the multifunction meter displays and tachometer
1. Turn the key to “OFF”.
2. Push and hold the “SELECT” button.
3. Turn the key to “ON”, and then release the “SELECT” button after five seconds.
4. Push the “RESET” button to select the desired brightness level.
5. Push the “SELECT” button to confirm the selected brightness level. The control mode changes to
the shift timing indicator light activity function.
To set the shift timing indicator light activity function
1. Push the “RESET” button to select one of the following indicator light activity settings:

The indicator light will stay on when activated. (This setting is selected when the indicator light stays
on.)

The indicator light will flash when activated. (This setting is selected when the indicator light flashes
four times per second.)

The indicator light is deactivated; in other words, it will not come on or flash. (This setting is selected
when the indicator light flashes once every two seconds.)
2. Push the ”SELECT” button to confirm the selected indicator light activity. The control mode changes
to the shift timing indicator light activation function.
ProCarManuals.com

1-5
FEATURES
GEN
INFO
NOTE:
NOTE: To set the shift timing indicator light activation function
The shift timing indicator light activation function can be set between 7000 r/min and 15000 r/m. From
7000 r/min to 12000 r/min, the indicator light can be set in increments of 500 r/min. From 12000 r/min to
15000 r/min, the indicator light can be set in increments of 200 r/min.
1. Push the “RESET” button to select the desired engine speed for activating the indicator light.
2. Push the “SELECT” button to confirm the selected engine speed. The control mode changes to the
shift timing indicator light deactivation function.
To set the shift timing indicator light deactivation function

The shift timing indicator light activation function can be set between 7000 r/min and 15000 r/min.
From 7000 r/min to 12000 r/min, the indicator light can be set in increments of 500 r/min. From 12000
r/min to 15000 r/min, the indicator light can be set in increments of 200 r/min.

Be sure to set the deactivation function to a higher engine speed than for the activation function,
otherwise the shift timing indicator light will remain deactivated.
1. Push the “RESET” button to select the desired engine speed for deactivating the indicator light.
2. Push the “SELECT” button to confirm the selected engine speed. The control mode changes to the
shift timing indicator light brightness function.
To adjust the shift timing indicator light brightness
1. Push the “RESET” button to select the desired indicator light brightness level.
2. Push the “SELECT” button to confirm the selected indicator light brightness level. The right display
will return to the odometer or tripmeter mode
ProCarManuals.com

7-4
30: Lean angle cut-off switch
(latch up detected)
41: Lean angle cut-off switch
(open or short circuit)
50: ECU internal malfunction
(memory check error)
FUEL INJECTION SYSTEMFI
EAS00899
ECU’S SELF-DIAGNOSTIC FUNCTION
The ECU is equipped with a self-diagnostic function in order to ensure that the engine control system is
operating normally. If this function detects a malfunction in the system, it immediately operates the en-
gine under substitute characteristics and illuminates the engine trouble warning light to alert the rider
that a malfunction has occurred in the system. Once a malfunction has been detected, a fault code is
stored in the memory of the ECU.

To inform the rider that the fuel injection system is not functioning, the engine trouble warning light
flashes when the start switch is being pushed to start the engine.

If a malfunction is detected in the system by the self-diagnostic function, this mode provides an ap-
propriate substitute characteristic operation, and alerts the rider of the detected malfunction by illumi-
nating an engine trouble warning light.

After the engine has been stopped, the fault code number appears from the lowest value in order of
precedence on the LCD meter. Once a fault code has been displayed, it remains stored in the memory
of the ECU until it is deleted.
EAS00900
Engine trouble warning light indication and FI system operating condition
Warning light
indication
ECU’s operationFI operationVehicle operation
Flashing*Warning provided
when unable to start
engineOperation stoppedUnable
Remains ONMalfunction detectedOperated with
substitute
characteristics
in accordance with the
description of the
malfunctionAble / Unable depend-
ing on the self-diag-
nostic fault code
* The warning light flashes when any one of the conditions listed below is present and the start switch is
pushed.
11: Cylinder identification sensor
12: Crankshaft position sensor
19: Sidestand switch
(open circuit in wire to ECU)
EAS00901
Checking for a defective engine trouble warning light bulb
The engine trouble warning light comes on for 1.4 seconds after the main switch has been turned “ON”
and when the start switch is being pushed. If the warning light does not come on under these condi-
tions, the warning light bulb may be defective.
ProCarManuals.com

7-7
Engine operation is not normal or the engine trouble warning light is on.
* Engine trouble warning light may not come on even if the engine operation is not normal.
The engine trouble warning light comes on.
Check the fault code number displayed on the me-
ter.
Identify the probable cause of malfunction. (Refer
to the “Diagnostic fault code table”.)
Check and repair the probable case of malfunc-
tion.
Fault code No.
appearFault code No.
disappear
Check and repair.
(Refer to “TROU-
BLESHOOTING DE-
TAILS”.)
Monitor the operation
of the sensors and
actuators in the diag-
nostic mode. (Refer
to “Diagnostic mode
table” in chapter 7)Check and repair.
(Refer to “FAIL-SAFE
ACTIONS TABLE”.)
Perform ECU reinstatement action. (Refer to “Re-
instatement method” in “TROUBLESHOOTING
DETAILS”.)
Turn the main switch to “OFF”, turn the main switch
back to “ON”, and then check if the fault code num-
ber is still displayed.
Erasing the malfunction history:*
The malfunction history is stored even if the main
switch is turned OFF.
The malfunction history must be erased in the
diagnostic mode. (Refer to the “Diagnostic mode
table (Diagnostic code No.62)”)Repairs completed
The engine trouble warning light does not come
on.
Check the operation of following sensors and ac-
tuators in the diagnostic mode (Refer to “Diagnos-
tic mode table” in chapter 7.)
Malfunction of en-
gineDefective sensor
or actuator
Check and repair
the inner parts of
engine. (Refer to
Chapter 5)Check and repair
the corresponding
sensor or actua-
tor.
* Operated when the engine trouble warning light is on.
Fault code
number displayed
Fault code number not displayed
OKNG
OK
OK
Check the engine condition.
OK NG
01: Throttle position
sensor (throttle
angle)
03: Intake air pressure
07: Vehicle speed pulse
09: Fuel system volt-
age (battery bolt)
21: Neutral switch
30: Ignition coil #1
31: Ignition coil #232: Ignition coil #3
33: Ignition coil #4
36: Injector #1
37: Injector #2
38: Injector #3
39: Injector #4
48: Al system solenoid
53: EXUP servo motor
56: Sub-throttle servo
motor
FUEL INJECTION SYSTEMFI
EAS00904
TROUBLESHOOTING CHART
ProCarManuals.com

7-8
FUEL INJECTION SYSTEMFI
NOTE:
NOTE:
EAS00905
DIAGNOSTIC MODE
It is possible to monitor the sensor output data
or check the activation of actuators without con-
necting the measurement equipment by simply
switching the meter indication from the normal
mode to the diagnostic monitoring mode.
Setting the diagnostic mode
1. Turn the main switch to “OFF” and set the en-
gine stop switch to “OFF”.
2. Disconnect the wire harness coupler from
the fuel pump.
3. Simultaneously press and hold the “SE-
LECT” and “RESET” buttons, turn the main
switch to “ON”, and continue to press the but-
tons for 8 seconds or more.

All displays on the meter disappear except the
clock and tripmeter displays.

“dIAG” appears on the LCD meter.
4. Press the “SELECT” button to select the CO
adjustment mode “Co” or the diagnostic
mode “dIAG”.
5. After selecting “dIAG”, simultaneously press
the “SELECT” and “RESET” buttons for 2 se-
conds or more to execute the selection.
6. Select the diagnostic code number that ap-
plies to the item that was verified with the
fault code number by pressing the “SELECT”
and “RESET” buttons.

The diagnostic code number appears on the
LCD meter (01-70).

To decrease the selected diagnostic code
number, press the “RESET” button. Press the
“RESET” button for 1 second or longer to auto-
matically decrease the diagnostic code num-
bers.

To increase the selected diagnostic code num-
ber, press the “SELECT” button. Press the
“SELECT” button for 1 second or longer to au-
tomatically increase the diagnostic code num-
bers.
ProCarManuals.com

7-12
FUEL INJECTION SYSTEMFI
NOTE: Diagnostic mode table
Switch the meter display from the regular mode to the diagnosis mode. To switch the display, refer to
“DIAGNOSTIC MODE”.

Check the intake air temperature and coolant temperature as close as possible to the intake air tem-
perature sensor and the coolant temperature sensor respectively.

If it is not possible to check it with an atmospheric pressure gauge, judge it by using 101.3 kPa as the
standard.

If it is not possible to check the intake air temperature, use the ambient temperature as reference.
Diagnostic
codeItemDescription of actionData displayed on meter
(reference value)
01
Throttle angleDisplays the throttle angle.

Check with throttle fully closed.

Check with throttle fully open.0
125 degrees

Fully closed position (15
18)

Fully open position (95
100)
02
Atmospheric
pressureDisplays the atmospheric pressure.
* Use an atmospheric pressure gauge to check the
atmospheric pressure.Compare it to the value
displayed on the meter.
03
Intake air pressureDisplays the intake air pressure.
Engine stop switch is on.
* Generate the pressure difference by cranking the engine
with the starter, without actually starting the engine.
Not cranking-atmospheric
pressure

Cranking-intake air pressure It
changes at the value whitch is
smaller than in the atomo-
spheric pressure.
05Intake temperatureDisplays the intake air temperature.
* Check the temperature in the air cleaner case.Compare it to the value
displayed on the meter.
06Coolant temperatureDisplays the coolant temperature.
* Check the temperature of the coolant.Compare it to the value
displayed on the meter.
07
Vehicle speed pulseDisplays the accumulation of the vehicle pulses that are
generated when the tire is spun.(0
999; resets to 0 after 999)
OK if the numbers appear on
the meter.
08Lean angle cut-off
switchDisplays the lean angle cut-off switch values.Upright: 0.4
1.4 V
Overturned: 3.7
4.4 V
09Fuel system voltage
(battery voltage)Displays the fuel system voltage (battery voltage).
Engine stop switch is on.0
18.7 V
Normally, approximately 12.0 V
20Sidestand switchDisplays that the switch is ON or OFF. (When the gear is in a
position other than neutral.)Stand retracted: ON
Stand extended: OFF
21Neutral switchDisplays that the switch is ON or OFF.Neutral: ON
In gear: OFF
30
Ignition coil #1After the engine stop switch has been turned from OFF to
ON, it actuates ignition coil #1 for five times every second
and illuminates the engine trouble warning light.
* Connect an ignition checker.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check that spark is generated,
5 times with the engine stop
switch ON.
31
Ignition coils #2After the engine stop switch has been turned from OFF to
ON, it actuates ignition coil #2 for five times every second
and illuminates the engine trouble warning light.
* Connect an ignition checker.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check that spark is generated,
5 times with the engine stop
switch ON.
ProCarManuals.com