2004 YAMAHA YZF-R1S coolant temperature

1-2
1
1 Clock
2 Speedometer
3 “SELECT” button
4 “RESET” button
5 Tachometer
6 Coolant temperature display / air intake
temperature display
7 Odometer / tripmeters / fuel reserve tripme-
ter / stopwatch
8 Shift timing indicator light
1 Clock
2 Speedometer
FEATURES
GEN
INFO
NOTE:
EAS00019
FEATURES
INSTRUMENT FUNCTIONS
Multi-function display
The multi-function meter unit is equipped with
the following:

a speedometer (which shows the riding
speed)

a tachometer (witch shows engine speed)

an odometer (which shows the total distance
traveled)

two tripmeters (which show the distance
traveled since they were last set to zero)

a fuel reserve tripmeter (which shows the
distance traveled since the fuel level warning
light came on)

a stopwatch

a clock

a coolant temperature display

an air intake temperature display

a self-diagnosis device

a display brightness and shift timing indicator
light control mode

Be sure to turn the key to “ON” before using the “SELECT” and “RESET” buttons.
Clock mode
Turn the key to “ON”.
To set the clock
1. Push the “SELECT” button and “RESET”
button together for at least two seconds.
2. When the hour digits start flashing, push the
“RESET” button to set the hours.
3. Push the “SELECT” button, and the minute
digits will start flashing.
4. Push the “RESET” button to set the minutes.
5. Push the “SELECT” button and then release
it to start the clock.
ProCarManuals.com

1-3
FEATURES
GEN
INFO
1 Coolant temperature display / air intake
temperature display
2 Odometer / tripmeters / fuel reserve tripme-
ter / stopwatch
3 Shift timing indicator light
NOTE:
NOTE:Odometer, tripmeter, and stopwatch modes
Push the “SELECT” button to switch the display
between the odometer mode “ODO”, the trip-
meter modes “TRIP A” and “TRIP B” and the
stopwatch mode in the following order:
TRIP A
TRIP B
ODO
Stopwatch

TRIP A
If the fuel level warning light comes on, the
odometer display will automatically change to
the fuel reserve tripmeter mode ”F-TRIP” and
start counting the distance traveled from that
point. In that case, push the ”SELECT” button to
switch the display between the various tripme-
ter, odometer, and stopwatch modes in the fol-
lowing order:
F-TRIP
Stopwatch
TRIP A
TRIP B

ODO
F-TRIP
To reset a tripmeter, select it by pushing the “SE-
LECT” button, and then push the “RESET” button
for at least one second. If you do not reset the fuel
reserve tripmeter manually, it will reset itself auto-
matically and the display will return to the prior
mode after refueling and traveling 5 km (3 mi).
Stopwatch mode
Standard measurement
1. Push the “RESET” button to start the stopwatch.
2. Push the “SELECT” button to stop the stopwatch.
3. Push the “SELECT” button again to reset the stopwatch.
Split-time measurement
1. Push the “RESET” button to start the stopwatch.
2. Push the “RESET” button to measure split-times. (The colon “:” will start flashing.)
3. Push the “RESET” button to display the final split-time or push the “SELECT” button to stop the stop-
watch and display total elapsed time.
4. Push the “SELECT” button to reset the stopwatch.
Coolant temperature display
The coolant temperature display indicates the temperature of the coolant. Push the “RESET” button to
switch the coolant temperature display to the air intake temperature display.
When the coolant temperature display is selected, “C” is displayed before the coolant temperature.
Air intake temperature display
The air intake temperature display indicates the temperature of the air drawn into the air filter case. Push
the “RESET” button to switch the coolant temperature display to the air intake temperature display.

Even if the air intake temperature is set to be displayed, the coolant temperature warning light comes
on when the engine overheats.

When the key is turned to “ON”, the coolant temperature is automatically displayed, even if the air
intake temperature was displayed prior to turning the key to “OFF”.

When the air intake temperature display is selected, “A” is displayed before thetemperature.
ProCarManuals.com

2-21
TIGHTENING TORQUESSPEC
NOTE 1:
NOTE 2:
ItemFastenerThreadQ’tyTightening torqueRemarksItemFastenersizeQtyNmm
kgft
lbRemarks
Main axle bearing housingBoltM63121.28.7
Shift fork shaft stopperBoltM62101.07.2
Stopper screwScrewM81222.216
Shift rod lock nut (rear)NutM6170.75.0Left thread
Shift rod lock nut (front)NutM6170.75.0
Shift rod jointBoltM61101.07.2
Shift armBoltM61101.07.2
E.C.U.ScrewM6270.75.0
Neutral switch—M101202.015
EXUP servo motor coverScrewM5220.21.5
Coolant temperature sensor—M121181.813
Cylinder identification sensorBoltM6180.85.7
Atmospheric pressure sensorScrewM5270.75.0
Crankshaft position sensorBoltM61101.07.2
Oil level switchBoltM62101.07.2
1. First, tighten the bolts to approximately 19 Nm (1.9 m
kg, 14 ft
lb) with a torque wrench following the
tightening order.
2. Retighten the bolts 67 Nm (6.7 m
kg, 48 ft
lb) with a torque wrench.
1. First, tighten the bolts to approximately 20 Nm (2.0 m
kg, 15 ft
lb) with a torque wrench following the
tightening order.
2. Loosen the all bolts one by one following the tightening order and then tighten them to 20 Nm (2.7
m
kg, 15 ft
lb) again.
3. Retighten the bolts further to reach the specified angle (60).
ProCarManuals.com

7-1
FUEL INJECTION SYSTEMFI
19Atmospheric pressure
sensor
20Fuel injection system
relay
21Engine trouble warning
light
22Lean angle cut-off
switch
23Air cut-off valve
13Coolant temperature
sensor
14Spark plug
15Cylinder identification
sensor
16Pressure regulator
17Battery
18ECU
1Ignition coil
2Air filter case
3Intake temperature
sensor
4Fuel delivery hose
5Fuel tank
6Fuel pump
7Fuel return hose
8Intake air presure sen-
sor
9Throttle position sen-
sor
10Fuel injector
11Catalytic converter
12Crankshaft position
sensor
FUEL INJECTION SYSTEM
FUEL INJECTION SYSTEM
ProCarManuals.com

7-3
FUEL INJECTION SYSTEMFI
1Main switch
4Fuse (main)
5Fuse (backup)
6Battery
7Fuse (fuel injection)
10Starting circuit cut-off relay
11Neutral switch
12Sidestand switch
13Fuel pump
14E.C.U.
15Ignition coil #1
16Ignition coil #2
17Ignition coil #3
18Ignition coil #4
19Spark plug
20Injector #1
21Injector #2
22Injector #3
23Injector #4
25Sub-throttle position sensor
26EXUP servo motor
27Speed sensor
28Coolant temperature sensor
29Intake air temperature sensor
31Crankshaft position sensor
32Throttle position sensor
33Intake air pressure sensor
34Atmospheric pressure sensor
35Cylinder identification sensor
36Lean angle cut-off switch
43Multi function meter
53Engine stop switch
73Fuse (ignition)
ProCarManuals.com

7-5
FUEL INJECTION SYSTEMFI
SUBSTITUTE CHARACTERISTICS OPERATION CONTROL (FAIL-SAFE ACTION)
If the ECU detects an abnormal signal from a sensor while the vehicle is being driven, the ECU illumi-
nates the engine trouble warning light and provides the engine with alternate operating instructions
that are appropriate for the type of malfunction.
When an abnormal signal is received from a sensor, the ECU processes the specified values that are
programmed for each sensor in order to provide the engine with alternate operating instructions that
enable the engine to continue to operate or stop operating, depending on the conditions.
The ECU takes fail-safe actions in two ways: one in which the sensor output is set to a prescribed value,
and the other in which the ECU directly operates an actuator. Details on the fail-safe actions are given
in the table below.
FAIL-SAFE ACTIONS TABLE
Fault
Code No.ItemSymptomFail-safe actionAble / unable
to startAble / unable
to drive
11
Cylinder identification
sensorNo normal signals are received from
the cylinder identification sensor.Continues to operate the engine based
on the results of the cylinder
identification that existed up to that
point.
UnableAble
12Crankshaft position
sensorNo normal signals are received from
the crankshaft position sensor.
Stops the engine (by stopping the
injection and ignition).UnableUnable
13
14Intake air pressure
sensor (open or short
circuit) (pipe system)Intake air pressure sensor-open or
short circuit detected.
Faulty intake air pressure sensor
system.
Fixes the intake air pressure to
101.3 kpa.
AbleAble
15
16Throttle position sensor
(open or short circuit)
(stuck)Throttle position sensor-open or short
circuit detected.
Fixes the throttle position sensor to
fully open.AbleAble
17EXUP servo motor
potention
(open or short circuit)EXUP servo motor potention-open or
short circuit detected.
Turn the EXUP servo motor toward
the open side for 3 seconds and then
stop it.AbleAble
18
EXUP servo motor (lock)A lock of the EXUP servo motor is
detected.
Perform the preventive control
against motor locking.
Perform the lock release operation
twice every 100 seconds.
AbleAble
19Sidestand switch (open
circuit in wire to ECU)Open circuit in the input line of ECU
No.15 terminal is detected when the
start switch is pressed.-- (No start)UnableUnable
20Intake air pressure
Atmospheric pressureDefective values are detected due to
the internal malfunction
Fixes the intake air pressure and
atmospheric pressure to 101.3 kpa.AbleAble
21Coolant temperature
sensorCoolant temperature sensor-open or
short circuit detected.
Fixes the coolant temperature to
60C.AbleAble
22Intake temperature
sensorIntake temperature sensor-open or
short circuit detected.
Fixes the intake temperature to 20C.AbleAble
23Atmospheric pressure
sensorAtmospheric pressure sensor-open or
short circuit detected.
Fixes the atmospheric pressure to
101.3 kpa.AbleAble
33
34
35
36
Faulty ignitionOpen circuit detected in the primary
lead of the ignition coil.
Cut the injection of other cylinder in
the same group with the cylinder that
the error is detected.
(Example: when the #1 cylinder is
detective, cut the injection of #1 and
#4 cylinders, when the #2 cylinder is
detective, cut the injection of #2 and
#3 cylinders).
Turn on the power to the air induction
solenoid to always cut-off the air.
Able
(depending
on the num-
ber of faulty
cylinders)Able
(depending
on the num-
ber of faulty
cylinders)
30
41Lean angle cut-off
switch (latch up
detected) (open or short
circuit)Lean angle cut-off switch-open or short
circuit detected.
Turns OFF the fuel injection system
relay of the fuel system.
UnableUnable
42Speed sensor, neutral
switchNo normal signals are received from the
speed sensor; or, an open or short
circuit is detected in the neutral switch.
Fixes the gear to the top gear.AbleAble
43Fuel system voltage
(monitor voltage)The ECU is unable to monitor the
battery voltage (an open circuit in the
line to the ECU).
Fixes the battery voltage to 12 V.AbleAble
44
Error in writing the
amount of CO
adjustment on
EEPROMAn error is detected while reading or
writing on EEPROM (CO adjustment
value).--
AbleAble
ProCarManuals.com

7-10
FUEL INJECTION SYSTEMFI
Diagnostic fault code table
Fault
code No.SymptomProbable cause of malfunctionDiagnostic
code
11
No normal signals are received from
the cylinder identification sensor.
Open or short circuit in wiring sub lead.

Open or short circuit in wiring harness.

Defective cylinder identification sensor.

Malfunction in ECU.

Improperly installed sensor.
—
12
No normal signals are received from
the crankshaft position sensor.
Open or short circuit in wiring harness.

Defective crankshaft position sensor.

Malfunction in pickup rotor.

Malfunction in ECU.

Improperly installed sensor.
—
13
Intake air pressure sensor-open or
short circuit detected.
Open or short circuit in wiring sub lead.

Open or short circuit in wiring harness.

Defective intake air pressure sensor.

Malfunction in ECU.
03
14
Faulty intake air pressure sensor hose
system; a hose is detached, causing
constant application of the
atmospheric pressure to the sensor;
or, the hose is clogged.
Intake air pressure sensor hose is detached, clogged,
kinked, or pinched.

Malfunction in ECU.
03
15
Throttle position sensor-open or
short circuit detected.
Open or short circuit in wiring sub lead.

Open or short circuit in wiring harness.

Defective throttle position sensor.

Malfunction in ECU.

Improperly installed throttle position sensor.
01
16A stuck throttle position sensor is
detected.
Stuck throttle position sensor.

Malfunction in ECU.01
17EXUP servo motor potention
circuit-open or short circuit detected.
Open or short circuit in wiring sub lead.

Detective EXUP servo motor (potention circuit).53
18EXUP servo motor is stuck.
Open or short circuit in wiring sub lead.

Stuck EXUP servo motor (mechanism).

Stuck EXUP servo motor (motor).53
19Open circuit in the input line of ECU
No.15 terminal is detected when the
start switch is pressed.
Open circuit in wiring harness (ECU Coupler).

Malfunction in ECU.20
20
When the main switch is turned to ON,
the atmospheric sensor voltage and
intake air pressure sensor voltage
differ greatly.
Atmospheric pressure sensor hose is clogged.

Intake air pressure sensor hose is clogged, kinked, or pinched.

Malfunction of the atmospheric pressure sensor in the
intermediate electrical potential.

Malfunction of the intake air pressure sensor in the
intermediate electrical potential.

Malfunction in ECU.
03
02
21Coolant temperature sensor-open or
short circuit detected.
Open or short circuit in wiring harness.

Defective coolant temperature sensor.

Malfunction in ECU.06
22Intake temperature sensor-open or
short circuit detected.
Open or short circuit in wiring harness.

Defective intake temperature sensor.

Malfunction in ECU.05
23Atmospheric pressure sensor-open or
short circuit detected.
Open or short circuit in wiring sub lead.

Defective atmospheric pressure sensor.

Malfunction in ECU.02
30The motorcycle has overturned.
Overturned.

Malfunction in ECU.08
33
Open circuit is detected in the primary
lead of the ignition coil (#1).
Open or short circuit in wiring harness.

Malfunction in ignition coil.

Malfunction in ECU.

Malfunction in a component of ignition cut-off circuit system.
30
ProCarManuals.com

7-12
FUEL INJECTION SYSTEMFI
NOTE: Diagnostic mode table
Switch the meter display from the regular mode to the diagnosis mode. To switch the display, refer to
“DIAGNOSTIC MODE”.

Check the intake air temperature and coolant temperature as close as possible to the intake air tem-
perature sensor and the coolant temperature sensor respectively.

If it is not possible to check it with an atmospheric pressure gauge, judge it by using 101.3 kPa as the
standard.

If it is not possible to check the intake air temperature, use the ambient temperature as reference.
Diagnostic
codeItemDescription of actionData displayed on meter
(reference value)
01
Throttle angleDisplays the throttle angle.

Check with throttle fully closed.

Check with throttle fully open.0
125 degrees

Fully closed position (15
18)

Fully open position (95
100)
02
Atmospheric
pressureDisplays the atmospheric pressure.
* Use an atmospheric pressure gauge to check the
atmospheric pressure.Compare it to the value
displayed on the meter.
03
Intake air pressureDisplays the intake air pressure.
Engine stop switch is on.
* Generate the pressure difference by cranking the engine
with the starter, without actually starting the engine.
Not cranking-atmospheric
pressure

Cranking-intake air pressure It
changes at the value whitch is
smaller than in the atomo-
spheric pressure.
05Intake temperatureDisplays the intake air temperature.
* Check the temperature in the air cleaner case.Compare it to the value
displayed on the meter.
06Coolant temperatureDisplays the coolant temperature.
* Check the temperature of the coolant.Compare it to the value
displayed on the meter.
07
Vehicle speed pulseDisplays the accumulation of the vehicle pulses that are
generated when the tire is spun.(0
999; resets to 0 after 999)
OK if the numbers appear on
the meter.
08Lean angle cut-off
switchDisplays the lean angle cut-off switch values.Upright: 0.4
1.4 V
Overturned: 3.7
4.4 V
09Fuel system voltage
(battery voltage)Displays the fuel system voltage (battery voltage).
Engine stop switch is on.0
18.7 V
Normally, approximately 12.0 V
20Sidestand switchDisplays that the switch is ON or OFF. (When the gear is in a
position other than neutral.)Stand retracted: ON
Stand extended: OFF
21Neutral switchDisplays that the switch is ON or OFF.Neutral: ON
In gear: OFF
30
Ignition coil #1After the engine stop switch has been turned from OFF to
ON, it actuates ignition coil #1 for five times every second
and illuminates the engine trouble warning light.
* Connect an ignition checker.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check that spark is generated,
5 times with the engine stop
switch ON.
31
Ignition coils #2After the engine stop switch has been turned from OFF to
ON, it actuates ignition coil #2 for five times every second
and illuminates the engine trouble warning light.
* Connect an ignition checker.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check that spark is generated,
5 times with the engine stop
switch ON.
ProCarManuals.com