2004 YAMAHA YZ125LC Front Fork

5-33
CHASFRONT FORK
9. Install:
9Slide metal 1
9Oil seal washer 2
To outer tube slot.
NOTE:
Press the slide metal into the outer tube with
fork seal driver 3.
10. Install:
9Oil seal 1
NOTE:
Press the oil seal into the outer tube with fork
seal driver 2.
11. Install:
9Stopper ring 1
NOTE:
Fit the stopper ring correctly in the groove in the
outer tube.
12. Install:
9Dust seal 1
NOTE:
Apply the lithium soap base grease on the inner
tube.
Fork seal driver:
YM-01442/90890-01442
Fork seal driver:
YM-01442/90890-01442
5XE-9-30-5B 4/30/03 9:41 AM Page 16

5-34
CHASFRONT FORK
13. Check:
9Inner tube smooth movement
Tightness/Binding/Rough spots Repeat the
steps 2 to 12.
14. Compress the front fork fully.
15. Fill:
9Front fork oil
Until outer tube top surface with recom-
mended fork oil 1.
cC
9Be sure to use recommended fork oil. If
other oils are used, they may have an ex-
cessively adverse effect on the front fork
performance.
9Never allow foreign materials to enter the
front fork.
16. After filling, pump the damper rod 1slowly
up and down more than 10 times to distrib-
ute the fork oil.
17. Fill:
9Front fork oil
Until outer tube top surface with recom-
mended fork oil once more.
18. After filling, pump the outer tube 1slowly
up and down (about 200 mm (7.9 in) stroke)
to distribute the fork oil once more.
NOTE:
Be careful not to excessive full stroke. A stroke
of 200 mm (7.9 in) or more will cause air to en-
ter. In this case, repeat the steps 15 to 18.
Recommended oil:
Suspension oil “01”
5XE-9-30-5B 4/30/03 9:41 AM Page 18

5-35
CHASFRONT FORK
19. Wait ten minutes until the air bubbles have
been removed from the front fork, and the
oil has dispense evenly in system before
setting recommended oil level.
NOTE:
Fill with the fork oil up to the top end of the outer
tube, or the fork oil will not spread over to every
part of the front forks, thus making it impossible
to obtain the correct level.
Be sure to fill with the fork oil up to the top of the
outer tube and bleed the front forks.
20. Measure:
9Oil level (left and right) a
Out of specification  Adjust.
NOTE:
Be sure to install the spring guide 2when
checking the oil level.
w
Never fail to make the oil level adjustment
between the maximum and minimum level
and always adjust each front fork to the
same setting. Uneven adjustment can
cause poor handling and loss of stability.
Standard oil level:
125 mm (4.92 in)
Extent of adjustment:
105~135 mm (4.13~5.31 in)
From top of outer tube with
inner tube and damper rod
1 1
fully compressed without spring.
5XE-9-30-5B 4/30/03 9:41 AM Page 20

5-36
CHASFRONT FORK
21. Measure:
9Distance a
Out of specificationTurn into the locknut.
23. Install:
9Push rod 1
9Fork spring 2
NOTE:
9Install the fork spring with the damper rod 3
pulled up.
9After installing the fork spring , hold the damper
rod end so that it will not go down.
24. Install:
9Spring seat 1
9Cap bolt 2
NOTE:
Fully finger tighten the cap bolt onto the damper
rod.
25. Tighten:
9Cap bolt (locknut) 1
NOTE:
Hold the locknut 2and tighten the cap bolt with
specified torque.
22. Loosen:
9Rebound damping adjuster 1
NOTE:
9Loosen the rebound damping adjuster finger
tight.
9Record the set position of the adjuster (the
amount of turning out the fully turned in posi-
tion).
Distance a a
:
19 mm (0.75 in) or more
Between damper rod 1 1
top and
locknut 2 2
top.
29 Nm (2.9 m•kg, 21 ft•lb)
5XE-9-30-5B 4/30/03 9:42 AM Page 22

5-37
CHASFRONT FORK
2. Tighten:
9Cap bolt 1
3. Adjust:
9Front fork top end a
30 Nm (3.0 m•kg, 22 ft•lb)
Front fork top end (standard) a a
:
5 mm (0.20 in)
26. Install:
9Cap bolt 1
To outer tube.
NOTE:
Temporarily tighten the cap bolt.
27. Install:
9Protector guide 1
EC5552A1
Installation
1. Install:
9Front fork 1
NOTE:
9Temporarily tighten the pinch bolts (under
bracket).
9Do not tighten the pinch bolts (handle crown)
yet.
4. Tighten:
9Pinch bolt (handle crown) 1
9Pinch bolt (under bracket) 2
cC
Tighten the under bracket to specified
torque. If torqued too much, it may cause
the front fork to malfunction.
23 Nm (2.3 m•kg, 17 ft•lb)
20 Nm (2.0 m•kg, 14 ft•lb)
5XE-9-30-5B 4/30/03 9:42 AM Page 24

5-38
CHASFRONT FORK
7. Adjust:
9Rebound damping force
NOTE:
Turn in the damping adjuster 1finger-tight and
then turn out to the originally set position.
5. Install:
9Brake hose holder 1
9Caliper 2
9Bolt (caliper) 3
NOTE:
Fit the brake hose holder cut aover the projec-
tion bon the front fork and clamp the brake
hose.
6. Install:
9Brake hose holder 1
9Bolt (brake hose holder) 2
9Protector 3
9Bolt (protector) 4
NOTE:
When installing the brake hose holder, align the
top aof the brake hose neck with the brake
hose holder bottom b. Then pass the brake
hose 5in front of the axle boss cand fit it into
the hose groove dso that the brake hose does
not contact the nut (wheel axle).
23 Nm (2.3 m•kg, 17 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
5XE-9-30-5B 4/30/03 9:42 AM Page 26

5-46
CHASSTEERING
Extent of removal Order Part name Q’ty Remarks
STEERING REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
Number plate
Handlebar Refer to “HANDLEBAR” section.
Front fender
1 Steering shaft nut 1
2 Front fork 2 Refer to “FRONT FORK” section.
3 Handle crown 1
4 Ring nut 1 Use special tool.
Refer to “REMOVAL POINTS”.
5 Under bracket 1
6 Ball race cover 1
7 Bearing (upper) 1
8 Bearing (lower) 1 Refer to “REMOVAL POINTS”.
9 Ball race 2 Refer to “REMOVAL POINTS”. Extent of removal:1Under bracket removal 2Bearing removal
2
1
w
Support the machine securely so there is no dan-
ger of it falling over.
23 Nm (2.3 m•kg, 17 ft•lb)
145 Nm (14.5 m•kg, 105 ft•lb)
9Tighten ring nut.
38 Nm (3.8 m•kg, 27 ft•lb)
9Loosen it one turn.
9Retighten it.
7 Nm (0.7 m•kg, 5.1 ft•lb)
TIGHTENING STEPS:
20 Nm (2.0 m•kg, 14 ft•lb)
4Nm (0.4 m•kg, 2.9 ft•lb)
EC560000
STEERING
5XE-9-30-5C 4/30/03 9:40 AM Page 16

5-49
CHASSTEERING
4. Install:
9Ring nut 1
Tighten the ring nut using the ring nut
wrench 2.
Refer to “STEERING HEAD INSPECTION
AND ADJUSTMENT” section in the CHAP-
TER 3.
5. Check the steering shaft by turning it lock to
lock. If there is any binding, remove the
steering shaft assembly and inspect the
steering bearings.
6. Install:
9Plain washer 1
7. Install:
9Front fork 1
9Handle crown 2
NOTE:
9Temporarily tighten the pinch bolts (under
bracket).
9Do not tighten the pinch bolts (handle crown)
yet.
8. Install:
9Plain washer 1
9Steering shaft nut 2
7 Nm (0.7 m•kg, 5.1 ft•lb)
145 Nm (14.5 m•kg, 105 ft•lb)
5XE-9-30-5C 4/30/03 9:40 AM Page 22