2004 YAMAHA YZ125LC Rear shock

CHAPTER 4
ENGINE
SEAT, FUEL TANK AND SIDE
COVERS.....................................................4-1
EXHAUST PIPE AND SILENCER..............4-3
RADIATOR..................................................4-4
CARBURETOR AND REED VALVE...........4-7
CYLINDER HEAD , CYLINDER AND
PISTON.....................................................4-17
CLUTCH AND PRIMARY DRIVEN
GEAR.......................................................4-30
KICK AXLE, SHIFT SHAFT AND
PRIMARY DRIVE GEAR...........................4-38
YPVS GOVERNOR...................................4-46
WATER PUMP..........................................4-49
CDI MAGNETO.........................................4-53
ENGINE REMOVAL..................................4-57
CRANKCASE AND CRANKSHAFT.........4-62
TRANSMISSION, SHIFT CAM AND
SHIFT FORK.............................................4-69
CHAPTER 5
CHASSIS
FRONT WHEEL AND REAR WHEEL........5-1
FRONT BRAKE AND REAR BRAKE.......5-10
FRONT FORK...........................................5-26
HANDLEBAR............................................5-39
STEERING................................................5-46
SWINGARM..............................................5-51
REAR SHOCK ABSORBER.....................5-59
5XE-9-30-0 3/24/03 11:08 PM Page 20

1-16
GEN
INFO
TORQUE-CHECK POINTS
EC1A0013
TORQUE-CHECK POINTS
Frame construction Frame to rear frame
Combined seat and tank Fuel tank to frame
Engine mounting Frame to engine
Engine bracket to engine
Engine bracket to frame
Steering Steering shaft to Steering shaft to frame
handlebar Steering shaft to handle crown
Handle crown to handlebar
Suspension Front Steering shaft to Front fork to handle crown
front fork Front fork to under bracket
Rear For link type Assembly of links
Link to frame
Link to shock absorber
Link to swingarm
Rear Installation of shock Shock absorber to frame
absorber
Rear Installation of swingarm Tightening of pivot shaft
Wheel Installation of wheel Front Tightening of front axle
Tightening of axle holder
Rear Tightening of rear axle
Wheel to sprocket
Brake Front Caliper to front fork
Brake disc to wheel
Tightening of union bolt
Master cylinder to handlebar
Tightening of air bleeder
Rear Brake pedal to frame
Brake disc to wheel
Tighening of union bolt
Master cylinder to frame
Tightening of air bleeder
Fuel system Fuel tank to fuel cock
NOTE:
Concerning the tightening torque, refer to “
MAINTENANCE SPECIFICATIONS” section in
the CHAPTER 2.
5XE-9-30-1B 3/24/03 11:06 PM Page 10

2-2
SPECGENERAL SPECIFICATIONS
Carburetor:
Type/Manufacturer TMXχ
38SS/MIKUNI
Spark plug:
Type/Manufacturer BR9EG/NGK (resistance type)
Gap 0.5~0.6 mm (0.020~0.024 in)
Clutch type: Wet, multiple-disc
Transmission:
Primary reduction system Gear
Primary reduction ratio 64/19 (3.368)
Secondary reduction system Chain drive
Secondary reduction ratio 49/13 (3.769)
Transmission type Constant mesh, 5-speed
Operation Left foot operation
Gear ratio: 1st 30/13 (2.308)
2nd 28/15 (1.867)
3rd 29/19 (1.526)
4th 24/19 (1.263)
5th 25/23 (1.087)
Chassis:USA, ZA, AUS, NZEUROPE,CDN
Frame type Semi double cradle←
Caster angle 25.6° 25.4°
Trail 108 mm (4.25 in) 104 mm (4.09 in)
Tire:
Type With tube
Size (front) 80/100-21 51M
Size (rear) 100/90-19 57M
Tire pressure (front and rear) 100 kPa (1.0 kgf/cm2, 15 psi)
Brake:
Front brake type Single disc brake
Operation Right hand operation
Rear brake type Single disc brake
Operation Right foot operation
Suspension:
Front suspension Telescopic fork
Rear suspension Swingarm (link type monocross suspension)
Shock absorber:
Front shock absorber Coil spring/oil damper
Rear shock absorber Coil spring/Gas, oil damper
Wheel travel:
Front wheel travel 300 mm (11.8 in)
Rear wheel travel 315 mm (12.4 in)
Electrical:
Ignition system CDI magneto
2
5XE-9-30-2A 5/10/03 1:57 PM Page 3

2-7
SPECMAINTENANCE SPECIFICATIONS
EC212201
CHASSIS
Item Standard Limit
Steering system:
Steering bearing type Taper roller bearing…
Front suspension:
Front fork travel 300 mm (11.8 in)…
Fork spring free length 479 mm (18.9 in) 474 mm (18.7 in)
Spring rate, STD K=4.0 N/mm…
(0.408 kg/mm, 22.8 lb/in)
Optional spring/Spacer Yes…
Oil capacity 662 cm
3…
(23.3 Imp oz, 22.38 US oz)
Oil level 125 mm (4.92 in)…
105~135 mm (4.13~5.31 in)…
(From top of outer tube with inner tube
and damper rod fully compressed
without spring.)
Oil grade Suspension oil “01”…
Inner tube outer diameter 48 mm (1.89 in)…
Front fork top end 5 mm (0.20 in)…
Rear suspension: USA, CDN, ZA
EUROPE
AUS, NZ
Shock absorber travel
132 mm (5.20 in)←…
Spring free length
260 mm (10.24 in) 275 mm (10.83 in)…
Fitting length
248 mm (9.76 in)265 mm (10.43 in)…

240.5~258.5 mm 255.5~273.5 mm…
(9.47~10.18 in)
(10.06~10.77 in)
Spring rate, STD K=44.0 N/mm K=Approx.…
(4.50 kg/mm, 46.0 N/mm
252.0 lb/in) (4.70 kg/mm,
263.2 lb/in)
Optional spring Yes←…
Enclosed gas pressure 1,000 kPa ←…
(10 kg/cm
2,
142 psi)
Swingarm:
Swingarm free play limit
End…
1.0 mm (0.04 in)
Side clearance…
0.2~0.9 mm
(0.008~0.035 in)
5XE-9-30-2A 5/10/03 1:57 PM Page 8

2-10
SPECMAINTENANCE SPECIFICATIONS
Part to be tightened Thread size Q'tyT ightening torqueNm m•kg ft•lb
Rear brake master cylinder and frame M 6 ×1.0 2 10 1.0 7.2
Rear brake master cylinder cap M 4 ×0.7 2 2 0.2 1.4
Rear brake hose union bolt (caliper) M10 ×1.25 1 30 3.0 22
Rear brake hose union bolt (master cylinder) M10 ×1.25 1 30 3.0 22
Rear wheel axle and nut M20 ×1.5 1 125 12.5 90
Nipple (spoke) – 72 3 0.3 2.2
Driven sprocket and wheel hub M 8 ×1.25 6 42 4.2 30
Disc cover and rear brake caliper M 6 ×1.0 2 7 0.7 5.1
Protector and rear brake caliper M 6 ×1.0 2 7 0.7 5.1
Chain puller adjust bolt and locknut M 8 ×1.25 2 16 1.6 11
Engine mounting:
Engine and frame (front) M10 ×1.25 1 64 6.4 46
Engine and frame (lower) M10 ×1.25 1 64 6.4 46
Engine bracket and frame M 8 ×1.25 2 34 3.4 24
Engine bracket and engine M 8 ×1.25 1 34 3.4 24
Pivot shaft and nut M16 ×1.5 1 85 8.5 61
Relay arm and swingarm M14 ×1.5 1 80 8.0 58
Relay arm and connecting rod M14 ×1.5 1 80 8.0 58
Connecting rod and frame M14 ×1.5 1 80 8.0 58
Rear shock absorber and frame M10 ×1.25 1 56 5.6 40
Rear shock absorber and relay arm M10 ×1.25 1 53 5.3 38
Rear frame and frame (upper) M 8 ×1.25 1 32 3.2 23
Rear frame and frame (lower) M 8 ×1.25 2 29 2.9 21
Swingarm and brake hose holder M 5 ×0.8 4 1 0.1 0.7
Swingarm and patch M 4 ×0.7 4 2 0.2 1.4
Chain tensioner mounting M 8 ×1.25 2 19 1.9 13
Chain support and swingarm M 6 ×1.0 3 7 0.7 5.1
Seal guard and swingarm M 5 ×0.8 4 6 0.6 4.3
Fuel tank mounting M 6 ×1.0 2 10 1.0 7.2
Fuel tank and fuel cock M 6 ×1.0 2 7 0.7 5.1
Fuel tank and seat set bracket M 6 ×1.0 1 7 0.7 5.1
Fuel tank and hooking screw (fitting band) M 6 ×1.0 1 7 0.7 5.1
Fuel tank and fuel tank bracket M 6 ×1.0 4 7 0.7 5.1
Air scoop mounting M 6 ×1.0 6 4 0.4 2.9
Front fender mounting M 6 ×1.0 4 7 0.7 5.1
Rear fender mounting (front) M 6 ×1.0 2 7 0.7 5.1
Rear fender mounting (rear) M 6 ×1.0 2 12 1.2 8.7
Side cover mounting M 6 ×1.0 2 7 0.7 5.1
Seat mounting M 8 ×1.25 2 19 1.9 13
Number plate M 6 ×1.0 1 7 0.7 5.1
NOTE:

- marked portion shall be checked for torque tightening after break-in or before each race.


 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
5XE-9-30-2A 5/10/03 1:57 PM Page 11

2-16
SPECCABLE ROUTING DIAGRAM
AInstall the brake hose so that its pipe portion
directs as shown and lightly touches the projec-
tion on the caliper.
BPass the brake hose into the brake hose
holders.
CIf the brake hose contacts the spring (rear
shock absorber), correct its twist.
DInstall the brake hose so that its pipe portion
directs as shown and lightly touches the
projection on the master cylinder. 1Master cylinder
2Brake hose holder
3Brake hose
5XE-9-30-2B 5/10/03 1:57 PM Page 32

3-2
MAINTENANCE INTERVALS
INSP
ADJ
Item Remarks
COOLING SYSTEM
Check coolant level and leakage
Check radiator cap operation
Replace coolantEvery two years
Inspect hoses
OUTSIDE NUTS AND BOLTS Refer to “STARTING
RetightenAND BREAK-IN” section
in the CHAPTER 1.
AIR FILTER
Clean and lubricateUse foam air-filter oil or
Replaceequivalent oil
FRAME
Clean and inspect
FUEL TANK, COCK
Clean and inspect
BRAKES
Adjust lever position and pedal height
Lubricate pivot point
Check brake disc surface
Check fluid level and leakage
Retighten brake disc bolts, caliper bolts,

master cylinder bolts and union bolts
Replace pads
Replace brake fluidEvery one year
FRONT FORKS
Inspect and adjust
Replace oilSuspension oil “01”
Replace oil seal
FRONT FORK OIL SEAL AND DUST SEAL
Clean and lubeLithium base grease
REAR SHOCK ABSORBER
(After
Inspect and adjustrain ride)
Lube Molybdenum disulfide grease
Retighten
CHAIN GUARD AND ROLLERS
Inspect
SWINGARM
Inspect, lube and retightenMolybdenum disulfide grease
RELAY ARM, CONNECTING ROD
Inspect, lube and retightenMolybdenum disulfide grease
STEERING HEAD
Inspect free play and retighten
Clean and lubeLithium base grease
Replace bearing
TIRE, WHEELS
Inspect air pressure, wheel run-out,

tire wear and spoke looseness
Retighten sprocket bolt
Inspect bearings
Replace bearings
LubricateLithium base grease
THROTTLE, CONTROL CABLE
Check routing and connectionYamaha cable lube or
LubricateSAE 10W-30 motor oil
After
break-
inEvery
raceEvery
thirdEvery
fifthAs re-
quired
3
5XE-9-30-3A 4/28/03 5:55 PM Page 3

3-4
PRE-OPERATION INSPECTION AND MAINTENANCE
INSP
ADJ
EC320000
PRE-OPERATION INSPECTION AND MAINTENANCE
Before riding for break-in operation, practice or a race, make sure the machine is in good operating
condition.
Before using this machine, check the following points.
EC321000
GENERAL INSPECTION AND MAINTENANCE
Item Routine Page
Coolant Check that coolant is filled up to the radiator filler cap.
Check the cooling system for leakage.P3-5~9
Fuel Check that a fresh mixture of oil and gasoline is filled in
the fuel tank. Check the fuel line for leakage.P1-12
Transmission oil Check that the oil level is correct. Check the crankcase
for leakage.P3-12~14
Gear shifter and clutch Check that gears can be shifted correctly in order and
that the clutch operates smoothly.P3-9
Throttle grip/Housing Check that the throttle grip operation and free play
are correctly adjusted. Lubricate the throttle grip and P3-10~11
housing, if necessary.
Brakes Check the play of front brake and effect of front and
rear brake.P3-17~23
Chain Check chain slack and alignment. Check that the chain
is lubricated properly.P3-24~26
Wheels Check for excessive wear and tire pressure. Check for
loose spokes and have no excessive play.P3-34~35
Steering Check that the handlebar can be turned smoothly and
have no excessive play.P3-35~36
Front forks and Check that they operate smoothly and there is no oil
rear shock absorber leakage.P3-26~33
Cables (wires) Check that the clutch and throttle cables move smooth-
ly. Check that they are not caught when the handlebars —
are turned or when the front forks travel up and down.
Muffler Check that the muffler is tightly mounted and has no
cracks.P3-15~16
Sprocket Check that the driven sprocket tightening bolt is
not loose.P3-24
Lubrication Check for smooth operation. Lubricate if necessary. P3-37
Bolts and nuts Check the chassis and engine for loose bolts and nuts. P1-16
Lead connectors Check that the CDI magneto, CDI unit, and ignition coil
are connected tightly.P1-6
Settings Is the machine set suitably for the condition of the
racing course and weather or by taking into account the
P7-1~25
results of test runs before racing? Are inspection and
maintenance completely done?
5XE-9-30-3A 4/28/03 5:55 PM Page 14