PERIODIC MAINTENANCE AND MINOR REPAIR
6
•Check tread depth and for damage.
9 * Tires•Replace if necessary.
√√√√ √
•Check air pressure.
•Correct if necessary.
10 * Wheel bearings•Check bearing for looseness or damage.√√√√
11 * Steering bearings•Check bearing play and steering for roughness.√√√√√•Lubricate with lithium-soap-based grease. Every 24,000 km
12 * Chassis fasteners•Make sure that all nuts, bolts and screws are
√√√√ √
properly tightened.
13 Centerstand•Check operation.
√√√√ √
•Lubricate.
14 * Front fork•Check operation and for oil leakage.√√√√
15 * Shock absorber assembly•Check operation and shock absorber for oil leakage.√√√√
16 * Carburetor•Adjust engine idling speed.√√√√√ √
17 * Autolube pump•Check operation.
√√√√
•Bleed if necessary.
18 Final transmission oil•Check vehicle for oil leakage.√√ √•Change.√√√
19 * V-belt•Replace. Every 10,000 km
20 * Front and rear brake
•Check operation.√√√√√ √
switches
ODOMETER READING (x 1,000 km)
NO. ITEMCHECK OR MAINTENANCE JOB
1
ANNUAL
CHECK
6121824
6-3
SCOOTER CARE AND STORAGE
7
•For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the
windshield. Test the product on
a small hidden part of the
windshield to make sure that it
does not leave any marks. If the
windshield is scratched, use a
quality plastic polishing
compound after washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea
or on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely cor-
rosive in combination with water, carry
out the following steps after each ride
in the rain, near the sea or on salt-
sprayed roads.
NOTE :
Salt sprayed on roads in the winter may
remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the
engine has cooled down.
ECA00012
Do not use warm water since it
increases the corrosive action of the
salt.
2. Apply a corrosion protection spray
on all metal, including chrome-
and nickel-plated, surfaces to
prevent corrosion.After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally
induced discoloring of stainless-
steel exhaust systems can be
removed through polishing.)
3. To prevent corrosion, it is
recommended to apply a corro-
sion protection spray on all metal,
including chrome- and nickel-
plated, surfaces.
4. Use spray oil as a universal
cleaner to remove any remaining
dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely
before storing or covering it.
7-2
SPECIFICATIONS
8
Chassis:
Frame type Steel tube underbone
Caster angle ((degree)) 25°
Trail 101.3 mm
Tires:
Front:
Type Tubeless
Size 2 1/2-16 42M
Manufacturer / Model MICHELIN / M29S TT
Rear:
Type Tubeless
Size 2 3/4-16 46M
Manufacturer / Model MICHELIN / M29S TT
Maximum load * 182 Kg
Air pressure (cold tire):
Up to 90 Kg load*
Front180 kpa
Rear 190 kpa
90 kg load — maximum
load *
Front180 kpa
Rear 210 kpa
* Total weight of rider, passenger, cargo and accessories.Wheels:
Front
Type Cast wheel
Size 16 X MT 1.60
Rear
Type Cast wheel
Size 16 X MT 1.85
Brakes:
Front
Type Single disc brake
Operation Right hand operation
Type brake fluid DOT 4
Rear
Type Single drum brake
Operation Left hand operation
Suspension:
Front suspension Telescopic fork
Rear suspension Unit swing
Shock absorber:
Front fork type Coil spring/oil damper
Rear shock absorber Coil spring/oil damper
assembly type
Wheel travel:
Front wheel travel 80 mm
Rear wheel travel 70 mm
8-2