2004 YAMAHA TT600RE turn signal bulb

SPECGENERAL SPECIFICATIONS
2-3
Item Standard Limit
Brakes
Front:
Type Single Ø 267 mm disk brake,
2 x 28 mm
Operation Right hand
Fluid DOT 4
Rear:
Type Single Ø 220 mm disk brake,
1 x 34 mm caliper
Operation Right foot
Fluid DOT 4
Suspension
Front Telescopic fork Outside tube
dia. 46 mm
Rear Deltabox Swingarm with
adjustable shock absorber
Spring/shock absorber
Front Coil spring / oil damper
RearCoil spring / gas-oil damper, spring
preload adjustable
Wheel travel
Front 230 mm •••
Rear 230 mm •••
Electrical system
Ignition system Transistorized coil ignition (digital)
Charging system:
Type A.C. magneto
Standard output 14V, 13.5A at 5.000 r/min •••
Battery:
Model GT9B-4
Voltage, capacity 12V, 8Ah •••
Headlight typeQuartz bulb (halogen)
Bulb voltage, wattage x quantity
Headlight 12V 60W / 55W x 1 •••
Tail/brake light 12V 5W / 21W x 1 •••
Turn signal light 12V 10W x 4 •••
Auxiliary light 12V 5W x 1 •••
Meter lighting 12V 3W x 1 •••
Turn signal indicator light 12V 1.2W x 1 •••
Neutral indicator light 12V 1.2W x 1 •••
Auxiliary indicator light 12V 1.2W x 1 •••
High beam indicator light 12V 1.2W x 1 •••
Fuse20A •••
ProCarManuals.com

ELECSIGNAL SYSTEM
7-57
CONTINUITY
DISCONTINUITY Replace the bulb and/or bulbholder.1. Bulb and bulbholder.
•Check the continuity of the bulb and bulb-
holder.
Refer to “BULB INSPECTION” section.
2. The rear stop light fails to turn on.
2. Brake switch.
•Disconnect the brake switch cables and
the connector from the wire harness.
•Connect the pocket tester ( Ωx 1) to the
brake switch terminals.
•Check the switch component for conti-
nuity between “Green/Yellow (1)” and
“Brown (2)”, or “Black (3)” and “Black (4)”. Refer to “SWITCH CHECK” section.
[A] Front brake switch
[B] Rear brake switch
INCORRECT
The brake switch is defective. Replace.
*
ON (Step down)
OFF (Free) BB
BB
G/Y Br
34
2
G/Y RW
1
ON (Pull in) OFF (Free)
G/Y
Br
A
B
Br
ProCarManuals.com

SIGNAL SYSTEM
7-58
ELEC
3. Voltage.
•Connect the pocket tester (DC 20V) to the
bulbholder connector.
Tester terminal (+) ➔Green/Yellow cable (1)
Tester terminal (–) ➔Black terminal (2)
•Turn the main switch to ON.
•The brake lever is pulled or the brake
pedal is pressed.
•Check the voltage (12V) on the
“Green/Yellow” cable of the bulbholder
connector.
OUT OF SPECIFICATION
The circuit from the main switch to the bulbhol-
der connector is defective. Repair.
IN COMPLIANCE WITH
SPECIFICATIONS (12V)
*
The circuit is efficient.
CONTINUITY
DISCONTINUITY
Replace the bulb and/or bulbholder.
3. The direction indicator light and/or the direc- tion indicator light fail to flash.
1. Bulb and bulbholder.
•Check the continuity of the bulb and bulb-
holder.
Refer to “BULB INSPECTION” section.
2. Direction indicator switch.
•Disconnect the left handlebar switch con-
nector from the wire harness.
•Connect the pocket tester ( Ωx 1) to the
left handlebar switch cables.
ProCarManuals.com

SIGNAL SYSTEM
7-60
ELEC
OUT OF SPECIFICATION The direction indicator lamp relay is defective.
Replace.
IN COMPLIANCE WITH
SPECIFICATIONS (12V)
* *
4. Voltage.
•Connect the pocket tester (DC 20V) to the
bulbholder connector.
Tester terminal (+) ➔
Brown/White terminal (1)
Tester terminal (–) ➔Earth
•Turn the main switch to ON.
•Check the voltage (12V) on the “Blue”
cable to the bulbholder connector.
ProCarManuals.com

ELECSIGNAL SYSTEM
7-61
5. Voltage.
•Connect the pocket tester (DC 20V) to the
bulbholder connector.
•Connect the left handlebar switch connec-
tor to the wire harness.
To the left flasher light:
Tester terminal (+) ➔
Green/Black terminal (1)
Tester terminal (–) ➔Earth
To the right flasher light:
Tester terminal (+) ➔
Brown/Black terminal (1)
Tester terminal (–) ➔Earth
•Turn the main switch to ON.
•Turn the direction indicator switch to “L” or
“R”.
•Check the voltage (it flashes at 2-8V) on
the “Green/Black” or “Brown/Black” cable
at the bulbholder connector.
OUT OF SPECIFICATION
The circuit from the direction indicator switch to
the bulbholder is defective. Repair.
IN COMPLIANCE WITH
SPECIFICATIONS (12V)
The circuit is efficient.
*
GBBrB
ProCarManuals.com

SIGNAL SYSTEM
7-62
ELEC
CONTINUITY
DISCONTINUITY Replace the bulb and/or bulbholder.1. Bulb and bulbholder.
•Check the continuity of the bulb and bulb-
holder.
Refer to “BULB INSPECTION” section.
2. Neutral switch.
•Disconnect the neutral switch cable from
the wire harness.
•Connect the pocket tester ( Ωx 1) to the
neutral switch cables.
•Check the switch component for continuity
between “Sky blue (1)” and “earth”.
Refer to “SWITCH CHECK” section.
INCORRECT
The neutral switch is defective. Replace.
CORRECT
4. The “N” neutral light fails to turn on.
3. Voltage.
•Connect the pocket tester (DC 20V) to the
bulbholder connector.
Tester terminal (+) ➔Brown cable (1)
Tester terminal (–) ➔Earth





\f 




\f  
 


ProCarManuals.com

ELECSIGNAL SYSTEM
7-63
The circuit is efficient.
IN COMPLIANCE WITH
SPECIFICATIONS (12V)
OUT OF SPECIFICATION
The circuit from the main switch to the bulbhol-
der connector is defective. Repair.•Turn the main switch to ON.
•Check the voltage (12V) on the Brown ca-
ble of the bulbholder connector.
4. Neutral switch cable.
•Disconnect the neutral switch connector
from the wire harness and the bulbholder
connector.
•Connect the pocket tester ( Ωx 1) to the
neutral switch cable (on the harness side)
and the bulbholder connector (1).
DISCONTINUITY
The circuit from the bulb to the neutral switch
cable is defective. Repair.
CONTINUITY
ProCarManuals.com