2004 YAMAHA TT600RE lock

CHASFRONT BRAKE
4-15
Brake fluid may deteriorate painted surfaces
or plastic parts. Always clean up spilled fluid
immediately.
CAUTION:
WARNING
•Use only designated quality brake fluid.
Otherwise, the rubber seals may deterio-
rate, causing leakage and poor brake per-
formance.
•Refill with the same type of brake fluid:
mixing fluids may result in a harmful chem-
ical reaction and lead to poor perform-
ance.
•Be careful that water does not enter the
significantly lower the boiling point of the
fluid may result in vapor lock.
4. Air bleed:
•Brake system
Refer to “AIR BLEEDING (HYDRAULIC
BRAKE SYSTEM)” section in CHAPTER 3.
5. Inspect:
•Brake fluid level
Lower than “MIN” mark ➔Fill.
Refer to “BRAKE FLUID INSPECTION”
section in CHAPTER 3.
(a) Minimum level mark “MIN”
6. Install:
•Diaphragm (1)
•Master cylinder cap (2)
•Screw (3) (cap) Screw (master cylinder cap): 1.5 Nm (0.15 mkg)
a
23
1
ProCarManuals.com

FRONT BRAKE
4-20
CHAS
2. Fill:
•Brake fluid reservoir
3. Air bleed:
•Brake system
Refer to “AIR BLEEDING (HYDRAULIC
BRAKE SYSTEM)” section in CHAPTER 3. Recommended brake fluid:
DOT 4
Brake fluid may deteriorate painted surfaces
or plastic parts. Always clean up spilled fluid
immediately.
CAUTION:
WARNING
•Use only designated quality brake fluid.
Otherwise, the rubber seals may deterio-
rate, causing leakage and poor brake per-
formance.
•Refill with the same type of brake fluid:
mixing fluids may result in a harmful chem-
ical reaction and lead to poor perform-
ance.
•Be careful that water does not enter the
significantly lower the boiling point of the
fluid may result in vapor lock.
4. Inspect:
•Brake fluid level
Lower than “MIN” mark ➔Fill.
Refer to “BRAKE FLUID INSPECTION”
section in CHAPTER 3.
(a) Minimum level mark “MIN”
a
WARNING
Check that the brake hose routing is correct.
Refer to “CABLE ROUTING” section.
ProCarManuals.com

REAR BRAKE
4-34
CHAS
MASTER CYLINDER INSTALLATION
1. Install:
•Brake pedal (refer to “BRAKE PEDAL
REMOVAL” section in this Chapter).
NOTE:
Lubricate the pin of the brake pedal with lithium-
base grease.
•Master cylinder
•Brake fluid reserve tank
•Plain washers (1) (new)
•Brake hose (2)
•Stop switch (to mount the brake hose) (3) Brake switch (brake hose): 20 Nm (2.0 mkg)
Master cylinder mounting bolt: 10 Nm (1.0 mkg)
Reserve tank mounting bolt: 4 Nm (0.4 mkg)New
2. Fill:
•Brake fluid reserve tank Recommended brake fluid: DOT 4
Brake fluid may deteriorate painted surfaces
or plastic parts. Always clean up spilled fluid
immediately.
CAUTION:
WARNING
•Use only designated quality brake fluid.
Otherwise, the rubber seals may deterio-
rate, causing leakage and poor brake per-
formance.
•Refill with the same type of brake fluid:
mixing fluids may result in a harmful chem-
ical reaction and lead to poor perform-
ance.
•Be careful that water does not enter the
significantly lower the boiling point of the
fluid may result in vapor lock.
ProCarManuals.com

REAR BRAKE
4-40
CHAS
2. Fill:
•Brake fluid reserve tank
Check that the brake hose has stayed in cor-
rect position with the pipe-fitting matching the
projection (a) of the caliper.
CAUTION:
WARNING
Check that the brake hose routing is correct.
Refer to “CABLE ROUTING” section.
Recommended brake fluid: DOT 4
Brake fluid may deteriorate painted surfaces
or plastic parts. Always clean up spilled fluid
immediately.
CAUTION:
WARNING
•Use only designated quality brake fluid.
Otherwise, the rubber seals may deterio-
rate, causing leakage and poor brake per-
formance.
•Refill with the same type of brake fluid:
mixing fluids may result in a harmful chem-
ical reaction and lead to poor perform-
ance.
•Be careful that water does not enter the
significantly lower the boiling point of the
fluid may result in vapor lock.
3. Air bleed:
•Brake system
Refer to “AIR BLEEDING (HYDRAULIC
BRAKE SYSTEM)” section in CHAPTER 3.
a
ProCarManuals.com

CHAS
4-63
STEERING
(1) Handle upper holder
(2) Handle lower holder
(3) Spacer
(4) Nut
(5) Plate washer
(6) Upper bracket (7) Brake hose holder
(8) Plate washer
(9) Special washer
(10) Upper ring nut
(11) Lower ring nut
(12) Ball race cover (13) Bearings
(14) Steering lock
(15) Steering axle
(16) Wire guide
TIGHTENING PROCEDURE
• Initial tightening 38 Nm (3.8 mkg)
• Loosen 1 turn
• Final tightening 4 Nm (0.4 mkg)
ProCarManuals.com

4-66
CHASSTEERING
3. Install:
•Ring nut (lower) (1)
Use the ring nut wrench (2).
Ring nut wrench: 90890-01268
NOTE:
Apply the lithium soap-base grease to the steer-
ing axle thread.
Lower ring nut tightening steps:
•Tighten the ring nut (1) using the ring nut
wrench.
Ring nut (lower)
(initial tightening): 38 Nm (3.8 mkg)
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
•Loosen the ring nut completely and retighten
it to specification.
WARNING
Do not tighten excessively.
Ring nut (lower)
(final tightening): 4 Nm (0.4 mkg)
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
4. Check the steering axle by turning it lock to lock. If there is any binding, remove the steer-
ing axle assembly and inspect the steering
bearings.
5. Install:
•Ring nut (upper) (1)
•Special washer (2)
ProCarManuals.com

CHASSTEERING
4-67
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼
Installation steps:
•Install the ring nut (upper) (1).
•Finger tighten the ring nut (upper), then align
the slots of both ring nuts. If not aligned, hold
the lower ring nut and tighten the other until
they are aligned.
•Install the special washer.
NOTE:
Make sure the special washer tabs are in the
slots.
6. Install:
•Upper bracket
•Fork legs (left and right) (1)
NOTE:
Temporarily install the under bracket pinch bolt to
achieve the correct fork position.
Front fork top end (a) (standard): 0 mm
7. Install:
•Plate washer (1)
•Steering axle nut (2)
Use the lock nut wrench (4).
Lock nut wrench (4):
90890-01348
NOTE:
Set the torque wrench to the lock nut wrench so that
they form a right angle.
Steering axle nut: 115 Nm (11.5 mkg)
ProCarManuals.com

CHASREAR SHOCK ABSORBER
4-71
(1) Rear shock absorber
(2) Spring
(3) Spring adjuster ring nut
(4) Lock ring nut
(5) End of stroke buffer
(6) Special spanner
ProCarManuals.com