2004 YAMAHA TT600RE battery

ELECELECTRICAL COMPONENTS
7-3
ELECTRICAL COMPONENTS
(1) Main wire harness
(2) Diodes
(3) Extension wire harness
(4) Rectifier/Regulator
(5) CDI ignition unit
(6) Battery (12V – 8Ah)
(7) Starter relay
(8) Fuse (20A) BATTERY: CAPACITY 12V – 8Ah
SPECIFIC GRAVITY: 1.320
ProCarManuals.com

IGNITION SYSTEM
7-12
ELEC
The diagram illustrates the ignition circuit inside the motorcycles electric system. NOTE:
For the colour code and legend, see page 7-2.
(1) AC generator/Pickup coil
(2) Rectifier/Regulator
(3) Battery
(6) Fuse
(7) Main switch
(9) Engine stop switch
(11) Diode (12) Clutch switch
(13) Sidestand switch
(14) Neutral switch
(15) Diode
(16) Ignitor unit
(17) Ignition coil

\f

\f\f
\f
\f
\f\f
\f\f
ProCarManuals.com

ELECIGNITION SYSTEM
7-13
DIAGNOSTICS IF THE IGNITION SYSTEM WERE TO STOP WORKING (NO OR INTERMITTENT SPARK)
Procedure
Check:
1. Fuse
2. Battery
3. Spark plug
4. Amplitude of ignition spark
5. Spark plug cap resistance
6. Ignition winding resistance 7. Main switch
8. Engine stop switch
9. Sidestand switch
10. Neutral switch
11. Clutch switch
12. Pick-up coil resistance
13. Wiring connections (whole connection sys- tem)
NOTE:
Before making the inspections mentioned, remove the following parts:
1. Seat
2. Rear cowling 3. Fuel tank
4. Cowling (headlight)
•To check functioning defects use the following special tools.
Dinamic spark tester: P/N. 90890-06754
Pocket tester:P/N. 90890-03112
1. Fuse
•Check the fuse for continuity.
Refer to “CHECKING THE FUSES” in
Chapter 3.
•Is the fuse OK?
YES
2. Battery
•Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in Chapter 3.
Min. open-circuit voltage:
2.8 V or more at 20°C (68°F)
•Is the battery OK?
NO
Replace the fuse.
NO
•Clean the battery terminals.
•Recharge or replace the battery.
YES
*
ProCarManuals.com

ELECTRICAL STARTING SYSTEM
7-22
ELEC
The diagram illustrates the electrical starting system-circuit inside the motorcycles electric system. NOTE:
For the colour code and legend, see page 7-2.
(3) Battery
(4) Starter relay
(5) Starting motor
(6) Fuse
(7) Main switch
(9) Engine stop switch (10) Starter switch
(11) Diode
(12) Clutch switch
(13) Sidestand switch
(14) Neutral switch
(15) Diode
\f(

365
12
11141315
4
ProCarManuals.com

ELECELECTRICAL STARTING SYSTEM
7-23
STARTING CIRCUIT OPERATION
The starting circuit on this model consists of the
starter motor, starter relay, and the starting circuit
cut-off relay. If the engine stop switch is on “RUN”
and the main switch is on “ON” (both switches are
closed), the starter motor can operate only if:
The starting circuit cut-off relay prevents the
starter from operating when neither of these con-
ditions have been met. In this instance, the start-
ing circuit cut-off relay is open so current cannot
reach the starter motor.
When at least one of the above conditions have
been met however, the starting circuit cut-off relay
is closed, and the engine can be started by press-
ing the starter switch.
WHEN THE TRANSMISSION IS IN
NEUTRAL
WHEN THE SIDESTAND IS UP AND
THE CLUTCH LEVER IS PULLED IN
1 Battery
2 Main switch
3 Engine stop switch
4 Starter relay
5 Starting circuit cut-off relay
6 Start switch
7 Starter motor
8 Neutral switch
9 Clutch switch
0 Sidestand switch
The transmission is in neutral (the neutral
switch is closed). or if
The clutch lever is pulled to the handlebar (the
clutch switch is closed) and the sidestand is up
(the sidestand switch is closed).
ProCarManuals.com

ELECTRICAL STARTING SYSTEM
7-24
ELEC
DIAGNOSTICS THE STARTER FAILS TO WORK
Procedure
Inspect:
(1) Fuse
(2) Battery
(3) Starting motor
(4) Starter relay
(5) Main switch (6) Engine stop switch
(7) Sidestand switch
(8) Neutral switch
(9) Clutch switch
(10) Starter switch
(11) Harness connections
NOTE:
Before starting inspections, remove the following parts:
1. Seat
2. Rear cowling 3. Fuel tank
4. Cowling (headlight)
•To check for defects use the following special tools.
Pocket tester: P/N. 90890-03112
1. Fuse.
•Remove fuse.
•Connect the pocket tester ( Ωx 1) to the
fuse.
•Check the fuse for continuity.
Refer to “CHECKING THE FUSES” in
Chapter 3.
2. Battery.
•Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in Chapter 3.
Min. open-circuit voltage:
12.8 V or more at 20°C (68°F)
CONTINUITY
DISCONTINUTY
Replace the fuse.
INCORRECT
•Clean the battery terminals.
•Recharge or replace the battery.
Refer to “BATTERY INSPECTION” in
Chapter 3.
*
CORRECT
ProCarManuals.com

ELECELECTRICAL STARTING SYSTEM
7-25
IT RUNS
IT FAILS TO RUN The starter is defective. Repair or replace.
IT FAILS TO RUNThe starter relay is defective. Replace.
3. Starter
•Connect the positive terminal of the bat-
tery (1) and the starter cable (2) using a
connection cable (3) *.
•Check the functioning of the starter.
WARNING
• A wire that is used as a jumper lead must have at least the same capacity of the bat-
tery lead, otherwise the jumper lead may
burn.
• This check is likely to produce sparks, therefore make sure that no flammable
gas or fluid is in the vicinity.
*
*
4. Starter relay.
•Disconnect the starter relay connector.
•Connect the battery and frame to the
starter relay connector, using a connec-
tion cable (1) as shown.
Battery terminal (+) (2) ➔
Red/Black terminal (3)
Frame ➔Blue/White terminal (4)
•Check the functioning of the starter.
*
IT RUNS
ProCarManuals.com

CHARGING SYSTEM
7-36
ELEC
The diagram illustrates the charging circuit inside the motorcycles electric system. NOTE:
For the colour code and legend, see page 7-2.
(1) AC generator/Pickup coil
(2) Rectifier/Regulator
(3) Battery
(6) Fuse
$%

ProCarManuals.com