2004 YAMAHA TT600RE fuel

1-5
GEN
INFO
SPECIAL TOOLS
SPECIAL TOOLS
The following special tools are necessary for complete and accurate tune-up and assembly. Use only the
appropriate special tools; this will help prevent damage caused by the use of inappropriate tools or impro-
vised techniques.
When placing an order, refer to the list provided below to avoid any mistakes.
Tool No.
90890-03113Engine tachometer
This tool is needed for detecting engine rpm.
90890-03141Timing light
This tool is needed for detecting ignition
timing.
90890-03112Pocket tester
These instruments are invaluable for check-
ing the electrical system.
90890-06754Ignition checker
This instrument is necessary for checking
the ignition system components.
Tool name / Usage Illustration
90890-03081Compression gauge
These tools are used to measure the engine
compression.
90890-04082Adapter (compression gauge)
This tool serves to measure the engine com-
pression.
90890-01312Fuel level gauge
This gauge is used to measure the fuel level
in the float chamber.
90890-01304Piston pin clip puller
This tool serves for removing the piston pin
clip.
ProCarManuals.com

SPECGENERAL SPECIFICATIONS
2-1
SPECIFICATIONS
GENERAL SPECIFICATIONS
Item Standard Limit
ModelTT600RE: 5CH5
Dimensions
Overall length 2,220 mm •••
Overall width 865 mm •••
Overall height 1,195 mm •••
Seat height 890 mm •••
Wheelbase 1,480 mm •••
Ground clearance 280 mm •••
Minimum turning radius 3,300 mm (right)
3,100 mm (left) •••
Basic weight (with oil and full
fuel tank)164.5 kg •••
Engine
Engine type Air cooled 4-stroke, SOHC
Cylinder arrangement Forward inclined single cylinder
Displacement 595 cm
3•••
Bore x stroke 95.0 x 84.0 mm •••
Compression ratio 8.5 : 1 •••
Starting system Electric starter
Lubrication system Dry sump with separate oil tank
Engine oil
Type
Temp. °CSAE20W40SE or SAE10W30SE •••
Recommended engine oil classification API Service SE, SF, SG or higher •••
Quantity:
Without oil filter cartridge
replacement 2.4 L •••
With oil filter cartridge
replacement 2.5 L •••
Total amount (dry engine) 3.0 L •••
Air filterWet type element
Fuel
Type Regular unleaded gasoline
Fuel tank capacity 10 L •••
Fuel reserve amount 3.0 L •••
Carburetor
Manufacturer TEIKEI
Model x quantity Y30PV-2ATK x 1
ProCarManuals.com

SPECMAINTENANCE SPECIFICATIONS
2-15
Tightening
Part to be tightened Thread torque
Remarkssize
N·mm·kg
Front brake:
Front hub/Disc brake M6 x 1.0 12 1.2
Front caliper/Front fork M8 x 1.25 25 2.5
Front caliper/Bleeder tightening M10 x 1.0 14 1.4
Union bolt tightening (front) M10 x 1.0 20 2.0
Rear brake:
Rear hub/Disc brake M6 x 1.0 12 1.2
Rear master cylinder/Frame M6 x 1.0 10 1.0
Rear stop switch/Rear master cylinder M10 x 1.0 20 2.0
Rear caliper/Bleeder tightening M10 x 1.0 14 1.4
Protector rear caliper/Rear caliper M6 x 1.0 10 1.0
Union bolt tightening (rear) M10 x 1.0 20 2.0
Rear brake tank reserve/Air cleaner assy M6 x 1.0 5 0.5
Brake pedal/Frame M10 x 1.25 48 4.8
Sidestand/Footrest:
Sidestand mounting bolt/Frame M12 x 1.25 40 4.0
Sidestand mounting bolt/Nut M12 x 1.25 40 4.0
Sidestand switch/Frame M5 x 0.8 8 0.8
Rear footrest/Rear frame M8 x 1.25 30 3.0
Bracket 1 (main footrest)/Frame M10 x 1.25 48 4.8
Bracket 2 (main footrest)/Frame M10 x 1.25 48 4.8
Footrest cover/Footrest M6 x 1.0 10 1.0
Seat, fuel tank and oil tank:
Seat/Frame M6 x 1.0 10 1.0
Bolt (guide seat)/Fuel tank M6 x 1.0 5 0.5
Fuel tank/Rear frame M6 x 1.0 12 1.2
Damper fuel tank (front)/Frame M8 x 1.25 15 1.5
Fuel tank/Fuel cock M6 x 1.0 7 0.7
Oil tank/Sub-oil tank M6 x 1.0 7 0.7
Union bolt (oil hose 2)/Oil tank assy/Engine M12 x 1.25 35 3.5
Oil hose 1/Oil tank/Engine M6 x 1.0 10 1.0
Oil tank/Rear frame M12 x 1.5 20 2.0
Frame, rear fender compl. and lights:
Rear fender compl. (under)/Rear frame M6 x 1.0 2 0.2
Rear fender compl. (upper)/Rear frame M6 x 1.0 7 0.7
Bracket, license/Rear frame M6 x 1.0 10 1.0
Bracket, license/Rear flasher M6 x 1.0 10 1.0
Horn/Frame M6 x 1.0 13 1.3
Regulator/Frame M8 x 1.25 7 0.7
Igniton coil/Frame M5 x 0.8 13 1.3
Battery box/Rear frame M6 x 1.0 7 0.7
Igniter cover/Battery box M4 1 0.1
Main switch/Frame M24 x 1.0 1 0.1
Tail light (lense)/Rear fender compl. M3.5 1 0.1
Starter switch/Red wire M6 x 1.0 7 0.7
ProCarManuals.com

SPECCABLE ROUTING
2-27









































(1) Front brake hose
(2) Brake hose holder
(3) Left tube guard
(4) Plastic plate
(5) Throttle cables
(6) Tachometer/
odometer cable
(7) Clutch cable
(8) Clutch cable holder
(9) Throttle cables
holder
(10) Wire harness band(11) Fuel pipe from fuel
cock
(12) Flasher relay
(13) Main relay
(14) Sidestand switch
(15) Diodes (n. 3)
(16) A.C. generator wire
harness (engine)
(17) Engine oil breather
pipe (to engine oil
tank)
(18) Main switch(19) Oil hose (oil tank to
engine)
(20) Oil hose (engine to
oil tank)
(21) C.D.I. unit
(22) Starting motor plus
cable
(23) Starting motor
minus cable
(24) Battery
(25) Starting relay
(26) Fuse (reserve)
(27) Fuse (main)(28) Wire extension
(29) Battery plus cable
[A] Lay the brake hose
behind the left tube
guard and fasten it
down by means of
the plate 4.
[B] Attach throttle
cables 5.
[C] Fasten the fuel pipe
11 to the tank.
[D] Fit the 3 diodes
inside the chassis,
against the coil clip.
ProCarManuals.com

INSP
ADJ
CHAPTER 3.
PERIODIC INSPECTION AND ADJUSTMENTS
INTRODUCTION..........................................................................................................3-1
PERIODIC MAINTENANCE/LUBRICATION INTERVALS........................................3-1
SEAT, FUEL TANK AND REAR COWLING................................................................3-3
REMOVAL ............................................................................................................3-3
INSTALLATION ....................................................................................................3-3
ENGINE........................................................................................................................3-4
VALVE CLEARANCE ADJUSTMENT ..................................................................3-4
DRIVE CHAIN ADJUSTMENT ..............................................................................3-7
IDLE SPEED ADJUSTMENT ................................................................................3-7
THROTTLE CABLE FREE PLAY ADJUSTMENT ................................................3-8
SPARK PLUG INSPECTION ................................................................................3-9
IGNITION TIMING CHECK ................................................................................3-11
COMPRESSION INSPECTION ..........................................................................3-12
ENGINE OIL LEVEL CHECK ..............................................................................3-15
ENGINE OIL REPLACEMENT ............................................................................3-17
ENGINE OIL PRESSURE CHECK ....................................................................3-21
CLUTCH ADJUSTMENT ....................................................................................3-21
AIR FILTER CLEANING ......................................................................................3-24
FUEL FILTER CLEANING ..................................................................................3-25
ENGINE OIL TANK FILTER CLEANING ............................................................3-26
SUCTION HOSE AND MANIFOLD INSPECTION..............................................3-28
FUEL LINE INSPECTION ..................................................................................3-28
CRANKCASE VENTILATION HOSE INSPECTION ..........................................3-29
EXHAUST SYSTEM INSPECTION ....................................................................3-29
CHASSIS....................................................................................................................3-30
ADJUSTING THE FRONT BRAKE ....................................................................3-30
ADJUSTING THE REAR BRAKE ......................................................................3-31
CHECKING THE BRAKE FLUID LEVEL ............................................................3-32
BRAKE PAD WEAR INSPECTION ....................................................................3-33
BRAKE HOSING INSPECTION ..........................................................................3-33
BRAKE CIRCUIT BLEEDING ............................................................................3-34
DRIVE CHAIN SLACK INSPECTION AND ADJUSTMENT..................................3-35
DRIVE CHAIN LUBRICATION ............................................................................3-36
FRONT FORK INSPECTION ..............................................................................3-37
ADJUSTING THE FRONT FORK ......................................................................3-37
REAR SHOCK ABSORBER ADJUSTMENT ......................................................3-38
STEERING INSPECTION ..................................................................................3-40
TYRE INSPECTION ............................................................................................3-41
WHEEL INSPECTION ........................................................................................3-44
SPOKE INSPECTION AND TIGHTENING ........................................................3-44
CABLE INSPECTION..........................................................................................3-45
LEVER AND PEDAL LUBRICATION ..................................................................3-45
SIDESTAND LUBRICATION ..............................................................................3-46
REAR SUSPENSION LUBRICATION ................................................................3-46
ProCarManuals.com

INSP
ADJINTRODUCTION/PERIODIC MAINTENANCE/
LUBRICATION INTERVALS
3-1
PERIODIC INSPECTION AND ADJUSTMENTS
INTRODUCTION
This chapter includes all information necessary to perform recommended inspections and adjustments.
These preventive maintenance procedures, if followed, will ensure more reliable vehicle operation and a
longer service life. The need for costly overhaul work will be greatly reduced. This information applies to
vehicles already in service as well as to new vehicles that are being prepared for sale. All service techni-
cians should be familiar with this entire chapter.
PERIODIC MAINTENANCE/LUBRICATION INTERVALS
ODOMETER READING (x 1,000 km)
ANNUAL N0. ITEM CHECK OR MAINTENANCE JOB
110 2030 40CHECK
1
*Fuel line• Check fuel hoses for cracks or damage. ✓✓ ✓✓ ✓•
• Check condition.
✓✓
2 Spurk plug• Clean and regap.
• Replace.✓✓
3 * Valves• Check valve clearance.
✓✓ ✓✓
• Adjust.
4Air filter element• Clean.✓✓
• Replace. ✓✓
5 Clutch• Check operation.
✓✓ ✓ ✓✓
• Adjust.
• Check operation, fluid level and vehicle for fluid leakeage.
6 * Front brake•(See NOTE). ✓✓ ✓ ✓✓ ✓•
• Replace brake pads. Whenever worm to the limit
• Check operation, fluid level and vehicle
•for fluid leakage. ✓✓ ✓ ✓✓ ✓
7 * Rear brake•(See NOTE).
• Replace brake pads. Whenever worm to the limit
8 * Brake hoses• Check for cracks or damage.✓✓✓✓ ✓• Replace. (See NOTE). Every 4 years
9 * Wheels• Check runout, spoke tightness and for damage.
✓✓✓ ✓
• Tighten spokes if necessary.
• Check tread depth and for damage.
10 * Tyres• Replace if necessary.
✓✓✓✓ ✓
• Check air pressure.
• Correct if necessary.
11 * Wheel bearings• Check bearing for looseness or damage.✓✓✓✓
12 * Swingarm• Check operation and for excessive play.✓✓✓✓
• Check chain slack.
13 * Drive chain• Make sure that the rear wheel is properly aligned.Every 500 km and after washing the
• Clean and lubricate.motorcycle or riding in the rain.
14 *Steering • Check bearing play and steering for roughness. ✓✓ ✓ ✓✓bearings
• Lubrificate with lithium-soap-based grease. Every 20,000 km
15 *Chassis • Make sure that all nuts, bolts and screws are properly
✓✓ ✓✓ ✓
fasteners•tightened.
16Sidestand• Check operation.
✓✓ ✓✓ ✓
• Lubricate.
17
*Sidestand
• Check operation and for oil leakage. ✓✓ ✓ ✓✓ ✓
switch
ProCarManuals.com

INSP
ADJ
SEAT, FUEL TANK AND REAR COWLING
3-3
SEAT, FUEL TANK AND REAR COWLING
Order Job name/Part name Q.ty Remarks
Seat, fuel tank and rear cowling Remove the parts in order.
removal
1 Seat 1
2 Fuel pipe 1NOTE:
Be sure the cap is properly tightened
and the fuel cock is in the “OFF” position
before removing the tank.
3 Fuel tank 1
4 Lamp connector 1 Disconnect.
5 Rear cowling 1NOTE:
Widen the rear cowling body sides carefully
to extract rear cowling from the chassis.
Reverse the removal procedure for instal-
lation.
ProCarManuals.com

VALVE CLEARANCE ADJUSTMENT
3-4
INSP
ADJ
ENGINE
VALVE CLEARANCE ADJUSTMENT
NOTE:
•Valve clearance must be adjusted when the
engine is at ambient temperature.
•Adjust valve clearance with the piston under
compression at top dead centre (T.D.C.).
WARNING
Hold the motorcycle firmly in place to prevent
it falling over during the operation.
1. Remove:
•Seat
•Fuel tank
See the section “ SEAT, FUEL TANK AND
REAR COWLING”.
2. Disconnect:
•Spark plug cap (1)
3. Remove:
•Spark plug
•Tappet cover (2) (intake)
•Tappet covers (3) (exhaust)
When removing the spark plug and tappet
cover, be careful not to drop foreign objects
inside the engine.
4. Remove:
•Cap (1)
•Cap (2)
CAUTION:
5. Turn the crankshaft anticlockwise using a
wrench.
1
2
3
12
ProCarManuals.com