2004 YAMAHA GRIZZLY 660 oil change

5-19
EBU00678
Differential gear oil
Make sure the differential gear oil is at the speci-
fied level. Add oil as necessary. (See pages 8-53–
8-55 for details.)
EBU13160
Coolant
Check the coolant level in the coolant reservoir
when the engine is cold. (The coolant level will
vary with engine temperature.) The coolant level is
satisfactory if it is between the minimum and max-
imum level marks on the coolant reservoir. If the
coolant level is at or below the minimum level
mark, add distilled water to bring the level up to the
maximum level mark. Change the coolant every
two years. (See pages 8-57–8-67 for details.)CAUTION:_ Hard water or salt water is harmful to the en-
gine. You may use soft water if you cannot get
distilled water. _
Recommended oil:
SAE 80 API GL-4 Hypoid gear oil
EE.book Page 19 Tuesday, April 1, 2003 12:23 PM

8-33 1. Engine oil filler cap
2. Dipstick
1. Bouchon de remplissage d’huile de moteur
2. Jauge
1. Tapa de relleno de aceite de motor
2. Varilla
EBU10991
Engine oil and oil filter cartridge
The engine oil level should be checked before
each ride. In addition, the oil must be changed and
the oil filter cartridge replaced at the intervals
specified in the periodic maintenance and lubrica-
tion chart.
To check the engine oil level
1. Remove panel F. (See page 8-31 for panel
removal and installation procedures.)
2. Place the ATV on a level surface.
3. Start the engine, warm it up for several min-
utes, and then turn it off.
4. Wait a few minutes until the oil settles.
5. Remove the engine oil filler cap and wipe off
the dipstick with a clean rag.
EE.book Page 33 Tuesday, April 1, 2003 12:23 PM

8-37 1. Engine oil drain bolt
1. Boulon de vidange de l’huile
1. Perno de drenaje del aceite de motor
To change the engine oil (with or without oil fil-
ter cartridge replacement)
1. Remove panel F. (See page 8-31 for panel
removal and installation procedures.)
2. Start the engine, warm it up for several min-
utes, and then turn it off.
3. Place an oil pan under the engine to collect
the used oil, and then remove the engine oil
filler cap.
4. Remove the engine oil drain bolt to drain the
oil from the crankcase.
EE.book Page 37 Tuesday, April 1, 2003 12:23 PM

8-49
5. Fill the final gear case with oil.CAUTION:_ Be sure no foreign material enters the final
gear case. _6. Install the filler bolt and tighten to the speci-
fied torque.
7. Check for oil leakage. If oil leakage is found,
check for the cause. Recommended oil:
See page 10-3.
Oil quantity:
Periodic oil change:
0.25 L
Total amount:
0.30 L
Tightening torque:
Filler bolt (final gear case):
23 Nm (2.3 m·kgf)
EE.book Page 49 Tuesday, April 1, 2003 12:23 PM

8-55
5. Fill the differential gear case with oil.CAUTION:
Be sure no foreign material enters the differen-
tial gear case. 6. Install the filler bolt and tighten it to the speci-
fied torque.
7. Check for oil leakage. If oil leakage is found,
check for the cause. Recommended oil:
SAE 80 API “GL-4” Hypoid gear oil
Oil quantity:
Periodic oil change:
0.28 L
Total amount:
0.33 L
EE.book Page 55 Tuesday, April 1, 2003 12:23 PM

10-3
Engine oil:
Quantity:
Without oil filter cartridge replacement 1.9 L
With oil filter cartridge replacement 2.0 L
Final gear case oil:
Type SAE80 API “GL-4” Hypoid gear oil
Quantity:
Periodic oil change 0.25 L
Total amount 0.30 L
Differential gear case oil:
Type SAE80 API “GL-4” Hypoid gear oil
Quantity:
Periodic oil change 0.28 L
Total amount 0.33 L
Air filter: Wet element
Fuel:
Type For Europe
REGULAR UNLEADED GASOLINE ONLY
For Oceania
UNLEADED GASOLINE ONLY
Fuel tank capacity 20 L
Fuel reserve amount 3.5 LModel YFM660F
EE.book Page 3 Tuesday, April 1, 2003 12:23 PM