2004 YAMAHA BT1100 brake pads

6
Owner’s tool kit .............................................................. 6-1
Periodic maintenance and lubrication chart .................... 6-2
Removing and installing panels ...................................... 6-5
Checking the spark plugs ................................................ 6-5
Engine oil and oil filter element ........................................ 6-7
Final gear oil .................................................................... 6-9
Cleaning the air filter element .......................................... 6-10
Adjusting the carburetors ................................................ 6-12
Adjusting the engine idling speed .................................... 6-12
Adjusting the throttle cable free play................................ 6-13
Adjusting the valve clearance .......................................... 6-13
Tires ................................................................................ 6-14
Cast wheels .................................................................... 6-16
Adjusting the clutch lever free play .................................. 6-17
Adjusting the brake pedal position .................................. 6-18
Checking the front and rear brake pads .......................... 6-19
Checking the brake fluid level .......................................... 6-19
Changing the brake fluid .................................................. 6-21
Adjusting the shift pedal position .................................... 6-21
Checking and lubricating the cables ................................ 6-22Checking and lubricating the
throttle grip and cable ...................................................... 6-22
Checking and lubricating the brake and shift
pedals .............................................................................. 6-23
Checking and lubricating the brake and
clutch levers .................................................................... 6-23
Checking and lubricating the sidestand .......................... 6-24
Checking the front fork .................................................... 6-24
Checking the steering ...................................................... 6-25
Checking the wheel bearings .......................................... 6-25
Battery ............................................................................ 6-26
Replacing the fuses ........................................................ 6-28
Replacing the headlight and auxiliary light bulb .............. 6-29
Replacing a turn signal light bulb .................................... 6-31
Replacing the tail/brake light bulb .................................... 6-31
Replacing the license plate light bulb .............................. 6-32
Front wheel ...................................................................... 6-32
Rear wheel ...................................................................... 6-33
Troubleshooting .............................................................. 6-35
Troubleshooting chart ...................................................... 6-36
PERIODIC MAINTENANCE AND MINOR REPAIREAU00462

EAU00462PERIODIC MAINTENANCE AND MINOR REPAIR
EAU03685
Periodic maintenance and lubrication chart
NOTE:
•The annual checks must be performed every year, except if a kilometer-based maintenance is performed instead.
•From 50,000 km, repeat the maintenance intervals starting from 10,000 km.
•Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and technical skills.
6-2
6
ODOMETER READING (x 1,000 km)ANNUALN0. ITEM CHECK OR MAINTENANCE JOB
1 10203040CHECK
1*Fuel line•Check fuel hoses and vacuum hose for cracks
√√√√ √or damage.
2*Fuel filter•Check condition.√√
•Check condition.
√√
3 Spurk plugs•Clean and regap.
•Replace.√√
4
*Valves•Check valve clearance.
√√√√•Adjust.
5 Air filter element•Clean.√√•Replace.√√
6 Clutch•Check operation.
√√ √√ √
•Adjust.
•Check operation,fluid level and vehicle
for fluid leakeage. √√ √√ √ √
7*Front brake
(See NOTE on page 6-4).
•Replace brake pads. Whenever worm to the limit

EAU00462
ODOMETER READING (x 1,000 km)ANNUALN0. ITEM CHECK OR MAINTENANCE JOB
1 10203040CHECK
•Check operation, fluid level and vehicle
for fluid leakage. √√ √√ √ √
8*Rear brake(See NOTE on page 6-4).
•Replace brake pads. Whenever worm to the limit
9*Brake hoses•Check for cracks or damage.√√√√ √•Replace. (See NOTE on page 6-4). Every 4 years
10*Wheels•Check runout and for damage.√√√√
•Check tread depth and for
damage.
11
*Tires•Replace if necessary.√√√√
•Check air pressure.
•Correct if necessary.
12*Wheel bearings•Check bearing for looseness or damage.√√√√
13*Swingarm•Check operation and for excessive play.√√√√•Lubrificate with lithium-soap-based grease. Every 50,000 km
14*Steering bearings•Check bearing play and steering for roughness.√√ √√ √•Lubrificate with lithium-soap-based grease. Every 20,000 km
15
*Chassis fasteners•Make sure that all nuts, bolts and screws are properly
√√√√ √tightened.
16 Sidestand•Check operation.
√√√√ √
•Lubricate.
17
*Sidestand
•Check operation and for oil leakage.√√ √√ √ √switch
18*Front fork•Check operation and for oil leakage. √√√√
19
*Rear shock absorber
•Check operation and shock absorber for oil leakage.√√√√
assembly
PERIODIC MAINTENANCE AND MINOR REPAIR
6-3
6

1. Front brake pad wear indicator groove
PERIODIC MAINTENANCE AND MINOR REPAIR
11
2
1
EAU00715
Checking the front and rear
brake pads
The front and rear brake pads must be
checked for wear at the intervals specified
in the periodic maintenance and lubrica-
tion chart. Each brake pad is provided with
a wear indicator, which allows you to
check the brake pad wear without having
to disassemble the brake. To check the brake pad wear, check the
position of the wear indicator while apply-
ing the brake. If a brake pad has worn to
the point that the wear indicator almost
touches the brake disc, have a Yamaha
dealer replace the brake pads as a set.
EAU03776
Checking the brake fluid level
Insufficient brake fluid may allow air to en-
ter the brake system, possibly causing it to
become ineffective.
Before riding, check that the brake fluid is
above the minimum level mark and replen-
ish if necessary.
A low brake fluid level may indicate worn
brake pads and/or brake system leakage.
If the brake level is low, be sure to check
the brake pads for wear and the brake sys-
tem for leakage.
EAU00462
6-19
6
1. Front brake master cylinder
2. Minimum level mark 1. Rear brake pad wear indicator groove

EAU00462PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
Observe these precautions:
•When checking the fluid level, make
sure that the top of the brake fluid
reservoir is level.
•Use only the recommended quality
brake fluid, otherwise the rubber
seals may deteriorate, causing leak-
age and poor braking performance.
•Refill with the same type of brake flu-
id. Mixing fluids may result in a harm-
ful chemical reaction and lead to poor
braking performance.
•Be careful that water does not enter
the brake fluid reservoir when refill-
ing. Water will significantly lower the
boiling point of the fluid and may re-
sult in vapor lock.
•Brake fluid may deteriorate painted
surfaces or plastic parts. Always
clean up spilled fluid immediately.
•As the brake pads wear, it is normal
for the brake fluid level to gradually
go down. However, if the brake fluid
level goes down suddenly, have a
Yamaha dealer check the cause.
6-20
6
1. Screw (x 2)
2. Right panel
2
1
1. Pin (x 2)
2. Pin seat (x 2)
Recommended brake fluid: DOT 4
21
1. Rear brake fluid reservoir
2. Minimum level mark

EAU00462
1. Nut (x 2) 1. Bulb socket
2. Bulb
PERIODIC MAINTENANCE AND MINOR REPAIR
1
1 2
1. Brake caliper (x 2)
2. Wheel axle pinch bolt
3. Wheel axle
4. Spacer (x 2)








EAUB0019
Replacing the license plate
light bulb
1. Remove the license plate light by re-
moving the nuts.
2. Remove the bulb socket from the li-
cense plate light by pulling it out.
3. Remove the defective bulb by pulling
it out.
4. Insert a new bulb into the socket.
5. Install the bulb socket into the license
plate light.
6. Install the license plate light by in-
stalling the nuts.
EAUB0015
Front wheel
To remove the front wheel
EW000122WARNING0
It is advisable to have a Yamaha dealer
service the wheel.
Securely support the motorcycle so
that there is no danger of it falling over.
1. Mark either side of the wheel so that it
can be installed in the original running
direction.
2. Remove the brake calipers by remov-
ing the bolts.
ECA00047
Do not pull the brake lever after the
brake caliper has been removed, other-
wise the brake pads will be forced shut.
3. Loosen the front wheel axle pinch
bolt, then the wheel axle.
4. Pull the wheel axle out together with
the spacers, and then remove the
wheel.
CAUTION:
6-32
6

EAU00462PERIODIC MAINTENANCE AND MINOR REPAIR
EAB00016
To install the front wheel
1. Lift the wheel up between the fork
legs.
2. Install the spacers and insert the
wheel axle.
3. Lower the front wheel so that it is on
the ground.
4. Install the brake calipers by installing
the bolts.
NOTE:
Make sure that there is enough space
between the brake pads before installing
the brake calipers onto the brake discs.5. Tighten the wheel axle, then the front
wheel axle pinch bolt, and the brake
caliper bolts to the specified torques.EAUB0017
Rear wheel
To remove the rear wheel
EW000122WARNING0
It is advisable to have a Yamaha dealer
service the wheel.
Securely support the motorcycle so
that there is no danger of it falling over.
1. Loosen the rear wheel axle pinch
bolt, and then remove the axle nut.
6-33
6
6. Push down hard on the handlebar
several times to check for proper fork
operation. Tightening torques:
Wheel axle:
75 Nm (7.5 m·kgf)
Front wheel axle pinch bolt:
25 Nm (2.5 m·kgf)
Brake caliper bolt:
42 Nm (4.2 m·kgf)
1. Wheel axle pinch bolt
2. Axle nut
3. Brake torque rod bolt



EAU00462PERIODIC MAINTENANCE AND MINOR REPAIR
2. Remove the brake torque rod bolt
from the brake caliper bracket, and
then turn the caliper up, away from
the disc.
3. Remove the wheel axle together with
the spacers.
4. Pull the wheel to the right to separate
it from the final gear case, and then
remove it.
ECA00062
Do not push the brake pedal after the
wheel has been removed together with
the brake disc, otherwise the brake
pads will be forced shut.
CAUTION:
EAUB0018
To install the rear wheel
1. Apply a light coating of lithium-soap-
based grease to the splines of the fi-
nal gear case and wheel hub.
2. Install the wheel by inserting the
wheel axle, then installing the axle
nut.
3. Turn the caliper down so that it fits
over the brake disc.
NOTE:
Make sure that there is enough space
between the brake pads before installing
the brake caliper onto the brake disc.
4. Install the wheel axle pinch bolt.
5. Install the brake torque rod bolt at the
brake caliper bracket.6. Install the wheel axle pinch bolt.
7. Lower the rear wheel so that it is on
the ground.
8. Tighten the axle nut, wheel axle pinch
bolt, and brake torque rod bolt to the
specified torques.
6-34
6
Tightening torques:
Axle nut:
110 Nm (11.0 m·kgf)
Wheel axle pinch bolt:
22 Nm (2.2 m·kgf)
Brake torque rod bolt:
35 Nm (3.5 m·kgf)