2004 YAMAHA BIG BEAR PRO 400 lock

7-17 1. Locknut 2. Adjusting screw
1. Contre-écrou 2. Vis de réglage
1. Contratuerca 2. Tornillo de ajuste
Speed limiter
For riders inexperienced with this model, this mod-
el is equipped with a speed limiter in the throttle le-
ver housing. The speed limiter limits the power
and top speed of the ATV. Turning the adjusting
screw in decreases top speed, and turning it out
increases top speed. (See page 4-19 for details.)
Loading and accessories
Use extra caution when riding the ATV with addi-
tional loads, such as accessories or cargo. The
ATV’s handling may be adversely affected. Re-
duce your speed when adding additional loads.
U4SH6B.book Page 17 Tuesday, May 27, 2003 4:39 PM

7-55
WARNING
_ Use proper gear and maintain steady speed
when climbing a hill.
If you lose all forward speed:

Keep weight uphill.


Apply the brakes.


Lock the parking brake after you are
stopped.
If you begin rolling backwards:


Keep weight uphill.


Never apply the rear brake while rolling
backwards. Apply the front brake.
When fully stopped, apply the rear brake
as well, and then lock the parking brake.
Dismount on uphill side or to a side if pointed
straight uphill. Turn the ATV around and re-
mount, following the procedure described in
the Owner’s Manual.
_
U4SH6B.book Page 55 Tuesday, May 27, 2003 4:39 PM

8-53 1. Locknut 2. Adjusting nut
1. Contre-écrou 2.Écrou de réglage
1. Contratuerca 2. Tuerca de ajuste
EBU00303
Valve clearance adjustment
The correct valve clearance changes with use, re-
sulting in improper fuel/air supply or engine noise.
To prevent this, the valve clearance must be ad-
justed regularly. This adjustment however, should
be left to a professional Yamaha service techni-
cian.
EBU00305
Select lever safety system cable adjustment
The select lever safety system cable stretches
with use, resulting in improper function.
To prevent this, the cable must be adjusted regu-
larly. This adjustment, however, should be left to a
Yamaha dealer.
U4SH6B.book Page 53 Tuesday, May 27, 2003 4:39 PM

8-55 1. Adjusting bolt 2. Locknut
a. Throttle lever free play
1. Boulon de réglage 2. Contre-écrou
a. Jeu du levier d’accélération
1. Perno de ajuste 2. Contratuerca
a. Juego libre de la palanca del acelerador
1. Brake pad a. Wear limit
1. Plaquette de frein a. Limite d’usure
1. Pastillas del freno a. Límite de desgaste
EBU00307
Throttle lever adjustmentNOTE:Adjust the engine idling speed before adjusting the
throttle lever free play.1. Loosen the locknut.
2. Turn the adjusting bolt until the throttle lever
free play is 3.0–5.0 mm.
3. Tighten the locknut.
EBU13770
Front brake pad check
Check the brake pads for damage and wear. If a
brake pad thickness is less than 1 mm, have a
Yamaha dealer replace the pads as a set.NOTE:_ The wheels need to be removed to check the
brake pads. (See page 8-79 for removal and in-
stallation procedures.) _
U4SH6B.book Page 55 Tuesday, May 27, 2003 4:39 PM

8-59
Observe these precautions:

When checking the brake fluid level, make sure
the top of the brake fluid reservoir is level.


Use only the designated quality brake fluid, oth-
erwise, the rubber seals may deteriorate, caus-
ing leakage and poor brake performance.


Refill with the same type of brake fluid. Mixing
fluids may result in a harmful chemical reaction
and lead to poor brake performance.


Be careful that water does not enter the brake
fluid reservoir when refilling. Water will signifi-
cantly lower the boiling point of the fluid and
may result in vapor lock.


Brake fluid may deteriorate painted surfaces or
plastic parts. Always clean up spilled fluid im-
mediately.


Have a Yamaha dealer check the cause if the
brake fluid level goes down. Recommended brake fluid: DOT 4
U4SH6B.book Page 59 Tuesday, May 27, 2003 4:39 PM

8-65 1. Locknut 2. Adjusting bolt
a. Brake pedal position
1. Contre-écrou 2. Boulon de réglage
a. Position de la pédale de frein
1. Contratuerca 2. Perno de ajuste
a. Posición del pedal del freno
EBU00334*
Rear brake pedal and lever adjustment
Pedal height adjustment
1. Loosen the locknut.
2. Turn the adjusting bolt so that the top of the
brake pedal is positioned 5.0 mm below the
top of the footrest.
3. Tighten the locknut.
U4SH6B.book Page 65 Tuesday, May 27, 2003 4:39 PM

8-69 1. Locknut 2. Adjusting bolt
1. Contre-écrou 2. Boulon de réglage
1. Contratuerca 2. Perno de ajuste
1. Adjusting nut (brake cable) 2. Lever
3. Pin a. Gap
1.Écrou de réglage (câble de frein) 2. Levier
3. Axe a. Jeu
1. Tuerca de ajuste (cable de freno)2. Palanca
3. Pasador a. Separación
Brake lever free play adjustment
1. Loosen the locknut and fully turn in the ad-
justing bolt at the brake lever.
2. Screw in the adjusting nut on brake cable to
provide a gap of 0–1.0 mm between the lever
and the pin.
U4SH6B.book Page 69 Tuesday, May 27, 2003 4:39 PM

8-71 1. Locknut 2. Adjusting bolt
a. Rear brake lever free play
1. Contre-écrou 2. Boulon de réglage
a. Jeu du levier de frein arrière
1. Contratuerca 2. Perno de ajuste
a. Juego de la palanca de freno trasero
3. Turn the adjusting bolt until free play at the
brake lever pivot is 4.0–7.0 mm.
4. Tighten the locknut.
WARNING
Operating with improperly serviced or adjust-
ed brakes could cause loss of braking ability,
which could lead to an accident.
After servicing:

Make sure the brakes operate smoothly
and that the free play is correct.


Make sure the brakes do not drag.
Replacement of brake components requires
professional knowledge. These procedures
should be performed by a Yamaha dealer.
U4SH6B.book Page 71 Tuesday, May 27, 2003 4:39 PM