2004 YAMAHA BANSHEE 350 oil

8-9
NOTE:
8Recommended brake fluid: DOT 4
8Brake fluid replacement:
9When disassembling the master cylinder or caliper cylinder, replace the brake fluid. Normally
check the brake fluid level and add the fluid as required.
9On the inner parts of the master cylinder and caliper cylinder, replace the oil seals every two
years.
9Replace the brake hoses every four years, or if cracked or damaged.

8-11
INITIAL CHAQUE
DESCRIPTION VÉRIFICATION 1 3 6 6 1
mois mois mois mois an
*Embrayage
9Examiner le jeu et le fonctionnement.
2
2229Changer si nécessaire.
9Contrôler la flèche et l’alignement de la chaîne.
Chaîne de 9Régrer si nécessaire.
transmission9Nettoyer et graisser.22229Changer si nécessaire.
*Guide-chaîne et
rouleau
9Contrôler l’usure et changer si nécessaire.222
*Système de direction
9Examiner le jeu, nettoyer et lubrifier.22222
*Suspension avant et
arrière
9Examiner et lubrifier.**22222
Pneus
9Examiner la pression d’air, le voile de roue, et
22222
l’usure de pneu.
*Roues
9Examiner les roulements.
222229Changer les roulements si nécessaire.
Câble d’accélération
9Contrôler le cheminement et le connexion.
et de commande9Lubrifier.22222
Ecrous et boulons
extérieur
9Resserrer.22222
Cadre
9Nettoyer et examiner.2222
Equipement
d’éclairage
9Examiner.22222
* Il est recomandé de confier ces opérations au concessionnaire Yamaha.
** Graisse à base de savon au lithium

8-17
EBU01098
Transmission oil
Transmission oil measurement
1. Place the machine on a level surface.
2. Warm up the engine for several minutes,
and then stop it.
3. Remove the oil filler cap and wipe off the
dipstick with a clean rag. Insert the dipstick
in the filler hole without screwing it in.
NOTE:
Wait a few minutes until the oil level settles
before checking.
4. Remove the dipstick and inspect the oil
level.
5. The oil level should be between the maxi-
mum and minimum marks. If the level is
low, add oil to raise it to the proper level.
6. Install the oil filler cap.
q
w
e
1. Dipstick
2. Maximum level mark 3. Minimum level mark
1. Jauge
2. Repère de niveau maximum 3. Repère de niveau minimum
1. Varilla de nivel
2. Marca de máximo 3. Marca de mínimo

8-19
Transmission oil replacement
1. Place the machine on a level surface.
2. Warm up the engine for several minutes
and then stop it.
3. Place a container under the engine to col-
lect the used oil.
4. Remove the oil filler cap and drain bolt to
drain the oil.
5. Install the drain bolt, and then tighten it to
the specified torque.
6. Fill the engine with oil and install the oil
filler cap.
q
1. Drain bolt
1. Boulon de vidange
1. Perno de vaciado
Tightening torque:
Drain bolt:
20 Nm (2.0 m0kgf)

8-21
cC
8In order to prevent clutch slippage (since
the engine oil also lubricates the clutch),
do not mix any chemical additives. Do not
use oils with a diesel specification of “CD”
or oils of a higher quality than specified. In
addition, do not use oils labeled “ENERGY
CONSERVING
II” or higher.
8Make sure that no foreign material enters
the crankcase.
Recommended oil:
See page 10-2.
Oil quantity:
Total amount:
1.7 L
Periodic oil change:
1.5 L

q
w
1. Maximum level mark
2. Minimum level mark
1. Repère maximum
2. Repère minimum
1. Marca de máximo
2. Marca de mínimo
8-23
7. Start the engine and warm up for a few
minutes. While warming up, check for oil
leakage. If oil leakage is found, stop the
engine immediately, and check for the
cause.
8. Check the oil level.
EBU01080
Cooling system
1. Check the coolant level in the coolant
reservoir when the engine is cold as the
coolant level will vary with engine temper-
ature. The coolant level should be
between the maximum and minimum
marks.

8-47
6. Inspect the element. If damaged, replace
it.
7. Apply SAE10W30 motor oil to the element.
NOTE:
The element should be wet but not dripping.
8. Reinstall the element to the element guide.
9. Reinstall the element assembly and parts
removed for access.

8-77
8Refill with the same type of brake fluid. Mixing
fluids may result in a harmful chemical reac-
tion and lead to poor brake performance.
8Be careful that water does not enter the brake
fluid reservoir when refilling. Water will signifi-
cantly lower the boiling point of the fluid and
may result in vapor lock.
8Brake fluid may deteriorate painted surfaces
or plastic parts. Always clean up spilled fluid
immediately.
8Have a Yamaha dealer check the cause if the
brake fluid level goes down.