2004 TOYOTA TUNDRA wheel

’04 TUNDRA_U (L/O 0309)
428
2004 TUNDRA from Sep. ’03 Prod. (OM34426U)
WHEN TO REPLACE YOUR WHEELS
If you have wheel damage such as
bending, cracks or heavy corrosion, the
wheel should be replaced.
If you fail to replace a damaged wheel,
the tire may slip off the wheel or cause
loss of handling control.
WHEEL SELECTION
When replacing wheels, care should be
taken to ensure that the wheels are re-
placed by ones with the same load ca-
pacity, diameter, rim width, and offset.
Correct replacement wheels are available
at your Toyota dealer.
A wheel of a different size or type may
adversely affect handling, wheel and bear-
ing life, brake cooling, speedometer/odom-
eter calibration, stopping ability, headlight
aim, bumper height, vehicle ground clear-
ance, and tire or snow chain clearance to
the body and chassis. Replacement with used wheels is not rec-
ommended as they may have been sub-
jected to rough treatment or high mileage
and could fail without warning. Also, bent
wheels which have been straightened may
have structural damage and therefore
should not be used. Never use an inner
tube in a leaking wheel which is designed
for a tubeless tire.
CAUTION
Observe the following instructions.
Otherwise, an accident may occur re-
sulting in death or serious injuries.
Do not use wheels other than the
manufacturer ’s recommended size,
as this may cause dangerous han-
dling characteristics resulting in
loss of control.
Fourwheel drive models:
Do not use wheels of different
brands, sizes and types, as this
may cause dangerous handling
characteristics resulting in loss of
control.
When installing aluminum wheels,
check that the wheel nuts are tight
after driving your vehicle the first 1600
km (1000 miles).
If you have rotated, repaired, or
changed your tires, check that the
wheel nuts are still tight after driving
1600 km (1000 miles).
When using tire chains, be careful not
to damage the aluminum wheels.
Use only the Toyota wheel nuts and
wrench designed for your aluminum
wheels.
When balancing your wheels, use only
Toyota balance weights or equivalent
and a plastic or rubber hammer.
As with any wheel, periodically check
your aluminum wheels for damage. If
damaged, replace immediately.
Replacing wheels
Aluminum wheel precautions

’04 TUNDRA_U (L/O 0309)
444
2004 TUNDRA from Sep. ’03 Prod. (OM34426U)
Tw o−wheel drive models
mm (in.)
Standard cab modelsAccess cab modelsDouble cab modelsStandard bedStepSide bed
Overall length5525 (217.5)∗1
5545 (218.3)∗25525 (217.5)∗1
5545 (218.3)∗25525 (217.5)∗1
5545 (218.3)∗25845 (230.1)
Overall width1910 (75.2)
1910 (75.2)
1945 (76.6)∗3
2015 (79.3)∗42000 (78.7)2015 (79.3)∗3
2025 (79.7)∗4
Overall height∗51795 (70.7)1790 (70.5)∗6
1800 (70.9)∗7or81790 (70.5)
1880 (74.0)∗6
1890 (74.4)∗7
1895 (74.6)∗8
Wheelbase3260 (128.3)3260 (128.3)3260 (128.3)3570 (140.5)
Front tread1680 (66.1)1680 (66.1)1680 (66.1)1680 (66.1)
Rear tread1648 (64.9)1648 (64.9)1648 (64.9)1710 (67.3)
∗1: With steel bumper∗2: With plastic bumper∗3: With wheel arch moulding∗4: With over fender∗5: Unladen vehicle∗6: With P245/70R16 tires∗7: With P265/70R16 tires∗8: With P265/65R17 tires
Dimensions

’04 TUNDRA_U (L/O 0309)
445
2004 TUNDRA from Sep. ’03 Prod. (OM34426U)
Four−wheel drive models
mm (in.)
Standard cab modelsAccess cab modelsDouble cab modelsStandard bedStepSide bed
Overall length5525 (217.5)∗1
5545 (218.3)∗25525 (217.5)∗1
5545 (218.3)∗25525 (217.5)∗1
5545 (218.3)∗25845 (230.1)
Overall width1910 (75.2)
1945 (76.6)∗3
1910 (75.2)
1945 (76.6)∗3
2015 (79.3)∗42000 (78.7)2015 (79.3)∗3
2025 (79.7)∗4
Overall height∗51805 (71.1)∗6
1815 (71.5)∗7or81810 (71.3)∗6
1820 (71.7)∗7or81810 (71.3)
1890 (74.4)∗6
1900 (74.8)∗7
1905 (75.0)∗8
Wheelbase3260 (128.3)3260 (128.3)3260 (128.3)3570 (140.5)
Front tread1675 (65.9)1675 (65.9)1675 (65.9)1675 (65.9)
Rear tread1648 (64.9)1648 (64.9)1648 (64.9)1710 (67.3)
∗1: With steel bumper∗2: With plastic bumper∗3: With wheel arch moulding∗4: With over fender∗5: Unladen vehicle∗6: With P245/70R16 tires∗7: With P265/70R16 tires∗8: With P265/65R17 tires

’04 TUNDRA_U (L/O 0309)
446
2004 TUNDRA from Sep. ’03 Prod. (OM34426U)
U.S.A. kg (lb.)
Cab type
EngineDriving systemTransmission typeGrade∗ 1Deck typePayload∗2
Standard cab
models5VZ −FETw o −wheel driveManual transmissionStandardStandard bed714 (1575)
Automatic transmissionStandardStandard bed701 (1545)
2UZ −FEFour −wheel driveAutomatic transmissionSR5Standard bed776 (1710)
Access cab
models
5VZ −FE
Tw o −wheel driveManual transmissionSR5Standard bed699 (1540)
Automatic transmissionSR5Standard bed678 (1495)
Four −wheel driveManual transmissionSR5Standard bed710 (1565)
Automatic transmissionSR5Standard bed689 (1520)
2UZ −FE
Tw o −wheel driveAutomatic transmission
SR5Standard bed794 (1750)
StepSide bed687 (1515)
LimitedStandard bed816 (1800)
StepSide bed726 (1600)
Four −wheel driveAutomatic transmission
SR5Standard bed669 (1475)
StepSide bed576 (1270)
LimitedStandard bed692 (1525)
StepSide bed601 (1325)
∗
1: See “Model code” on page ix in the beginning of this m anual if you are not sure of which model your vehicle is.∗
2:
Maximum payload including weight of driver, passengers, optional equipment and cargo
Payload

’04 TUNDRA_U (L/O 0309)
447
2004 TUNDRA from Sep. ’03 Prod. (OM34426U)
kg (lb.)
Cab type
EngineDriving systemTransmission typeGrade∗ 1Deck typePayload∗2
Double cab
models2UZ −FE
Tw o −wheel driveAutomatic transmissionSR5Standard bed851 (1875)
LimitedStandard bed826 (1820)
Four −wheel driveAutomatic transmissionSR5Standard bed742 (1635)
LimitedStandard bed717 (1580)
Canada kg (lb.)
Cab type
EngineDriving systemGrade∗ 1Payload∗2
Standard cab models5VZ −FETw o −wheel driveStandard708 (1560)
2UZ −FEFour −wheel driveStandard782 (1725)
Access cab models2UZ −FE
Tw o −wheel driveSR5787 (1735)
Four −wheel driveSR5662 (1460)
Limited685 (1510)
Double cab models2UZ −FE
Tw o −wheel driveSR5844 (1860)
Four −wheel driveSR5735 (1620)
Limited712 (1570)
∗
1: See “Model code” on page ix in the beginning of this m anual if you are not sure of which model your vehicle is.∗
2:
Maximum payload including weight of driver, passengers, optional equipment and cargo

’04 TUNDRA_U (L/O 0309)
448
2004 TUNDRA from Sep. ’03 Prod. (OM34426U)
kg (lb.)
Standard cab
models
5VZ −FE engineTw o −wheel drive modelsWithout towing package2358 (5200)
2UZ −FE engineFour −wheel drive modelsWithout towing package2494 (5500)
With towing package3311 (7300)
Access cab models
5VZ −FE engineTw o −wheel drive modelsWithout towing package2268 (5000)
Four −wheel drive modelsWithout towing package2268 (5000)
2UZ −FE engine
Tw o −wheel drive modelsWithout towing package2494 (5500)
With towing package3311 (7300)
Four −wheel drive modelsWithout towing package2358 (5200)
With towing package3175 (7000)
Double cab models2UZ −FE engine
Tw o −wheel drive modelsWithout towing package2358 (5200)
With towing package3176 (7000)
Four −wheel drive modelsWithout towing package2222 (4900)
With towing package3039 (6700)
∗: Trailer weight + car go weight
Towing capacity∗

’04 TUNDRA_U (L/O 0309)
451
2004 TUNDRA from Sep. ’03 Prod. (OM34426U)
CLUTCH
Pedal free play, mm (in.):
5—15 (0.2—0.6)
Fluid type: SAE J1703 or FMVSS No.116 DOT 3
MANUAL TRANSMISSION
Oil capacity, L (qt., Imp. qt.): Tw o −wheel drive models
2.6 (2.7, 2.3)
Four −wheel drive models
2.2 (2.3, 1.9)
Oil type: Gear oil API GL −4 or GL −5
Recommended oil viscosity: SAE 75W −90
AUTOMATIC TRANSMISSION
Fluid capacity (drain and refill), L (qt.,
Imp. qt.): Up to 2.0 (2.1, 1.8)
Fluid type: Toyota Genuine ATF Type T −IV
Change automatic transmission fluid only
as necessary. Generally, it is necessary to change
automatic transmission fluid only if your
vehicle is driven under one of the Special
Operating Conditions listed in your
“Scheduled Maintenance Guide” or
“Owner ’s Manual Supplement”. When
changing the automatic transmission fluid,
use only “Toyota Genuine ATF Type T
−IV”
(ATF JWS3309 or NWS6500) to aid in
assuring optimum transmission perfor-
mance.
Notice: Using automatic transmission
fluid other than “Toyota Genuine ATF
Type TIV” may cause deterioration in
shift quality, locking up of your trans-
mission accompanied by vibration, and
ultimately damage the automatic trans-
mission of your vehicle.
Please contact your Toyota dealer for fur-
ther details.
TRANSFER
Oil capacity, L (qt., Imp. qt.):
1.0 (1.1, 0.9)
Oil type: Gear oil API GL−4 or GL−5
Recommended oil viscosity: SAE 75W −90 DIFFERENTIAL
Oil capacity, L (qt., Imp. qt.):
Front1.15 (1.2, 1.0)
Rear
Standard and access cab modelsTw o −wheel drive models
Standard differential 3.80 (4.0, 3.3)
Limited− slip differential
3.15 (3.3, 2.8)
Four −wheel drive models
Standard differential 3.50 (3.7, 3.1)
Limited− slip differential
2.95 (3.1, 2.6)
Double cab models Standard differential4.00 (4.2, 3.5)
Limited− slip differential
3.35 (3.5, 2.9)
Oil type:
Standard differentialHypoid gear oil API GL −5
Li

mited− slip differential
Hypoid gear oil for limited −slip differ-
ential API GL −5

’04 TUNDRA_U (L/O 0309)
452
2004 TUNDRA from Sep. ’03 Prod. (OM34426U)
Recommended oil viscosity:
FrontSAE 75W −90
Rear Standard differential
Synthetic oil SAE 75W −140
Limited− slip differential
Above −18 C (0 F)
SAE 90
Below −18 C (0 F)
SAE 80W or 80W −90
CHASSIS LUBRICATION
Propeller shafts: SpidersLithium base chassis grease, NLGI
No.2
Double cardan joint Molybdenum −disulfide lithium base
chassis grease, NLGI No.2
Slide yokes Lithium base chassis grease, NLGI
No.2 or Molybdenum −disulfide lithium
base chassis grease, NLGI No.2 BRAKES
Minimum pedal clearance when depressed
with the force of 490 N (50 kgf, 110 lbf)
with the engine running, mm (in.):
Without vehicle stability control system95 (3.7)
With vehicle stability control system 80 (3.1)
Pedal free play, mm (in.): 1—6 (0.04—0.24)
Pad wear limit, mm (in.): 1.0 (0.04)
Lining wear limit, mm (in.): 1.0 (0.04)
Parking brake adjustment: Pedal type—when depressed with the
force of 294 N (30 kgf, 66.1 lbf)8—10 clicks
Lever type—when pulled with the force
of 196 N (20 kgf, 44 lbf) 8—12 clicks
Fluid type: SAE J1703 or FMVSS No.116 DOT 3 STEERING
Wheel free play:
Less than 30 mm (1.2 in.)
Power steering fluid type: Automatic transmission fluid DEXRON II
or III