2004 SUZUKI GRAND VITARA switch

YH4
GRAND
VITARA
1. Steering column
2. Mounting bolt
3. Steering column lower seal
4. Dash panel
1. Steering column lower seal
In engine room
In cabin
3C-8 STEERING WHEEL AND COLUMN
4) Check steering column lower seal for breakage or deformation.
If found defective, replace.
5) Check steering shaft joints and shaft for any damages such as
crack, breakage, malfunction or excessive play.
If anything is found faulty, replace as steering lower shaft assem-
bly or steering column assembly.
6) Check steering shaft for smooth rotation.
If found defective, replace as column assembly.
7) Check steering shaft and column for bend, cracks or deforma-
tion.
If found defective, replace as column assembly.
INSTALLATION
CAUTION:

After tightening steering column mounting bolts, steering
shaft joint bolts should be tightened.

After tightening steering column lower bolts, steering col-
umn upper bolts should be tightened.
1) Be sure that front wheels and steering wheel are in straight-
ahead position.
2) If equipped with shift (key) interlock cable, install shift (key) inter-
lock cable to ignition switch.
3) Install steering column assembly to dash panel and upper
bracket so that boss of steering column lower seal and all around
it project out of hole in dash panel into engine room. Tighten
steering column lower bolts (4 pieces) first and then upper bolts
(2 pieces) to specified torque.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)

YH4
GRAND
VITARA
1. Steering shaft joint
2. Steering shaft (column side)
3. Marks
1. Steering shaft joint
2. Bolt (column side)
3. Bolt (lower shaft assembly side)
1. Steering column hole cover
: If equipped
*
STEERING WHEEL AND COLUMN 3C-9
4) Install steering shaft joint to steering shaft by matching it to
marks made before removal.
5) Install shaft joint bolt (column side) to steering shaft joint. Tighten
shaft joint bolt (column side) to specified torque first and then
shaft joint bolt (lower shaft assembly side) to specified torque.
Tightening Torque
(b): 25 N
.m (2.5 kg-m, 18.0 lb-ft)
6) If combination switch is removed, install combination switch.
Refer to ªCOMBINATION SWITCHº in this section.
7) Connect all connectors that have been removed in removal.
8) Install steering column hole cover.
9) If steering wheel is removed, install steering wheel. Refer to
ªSTEERING WHEELº in this section.
10) Connect negative battery cable.

YH4
GRAND
VITARA
1. Steering column
2. Steering lock
1. Center punch (with sharp point)
2. Steering lock mounting bolt
1. Steering column
2. Steering shaft
3C-10 STEERING WHEEL AND COLUMN
STEERING LOCK ASSEMBLY (IGNITION
SWITCH)
REMOVAL
1) Remove steering column. Refer to ªSTEERING COLUMNº in
this section.
2) Using center punch as shown, loosen and remove steering lock
mounting bolts.
NOTE:
Use care not to damage aluminum part of steering lock
body with center punch.
3) Turn ignition key to ªACCº or ªONº position and remove steering
lock assembly from steering column.
INSTALLATION
1) Position oblong hole of steering shaft in the center of hole in col-
umn.
2) Turn ignition key to ªACCº or ªONº position and install steering
lock assembly onto column.
3) Now turn ignition key to ªLOCKº position and pull it out.
4) Align hub on lock with oblong hole of steering shaft and rotate
shaft to assure that steering shaft is locked.
5) Tighten new bolts until head of each bolt is broken off.
6) Turn ignition key to ªACCº or ªONº position and check to be sure
that steering shaft rotates smoothly. Also check for lock opera-
tion.
7) Install steering column. Refer to ªSTEERING COLUMNº in this
section.

YH4
GRAND
VITARA
1. Steering column assembly
2. Steering shaft joint
3. Marks
1. Steering column assembly
2. Steering shaft joint
3. Steering lower shaft assembly
4. Bolt (column side)
5. Bolt (lower shaft assembly side)
1. Steering lower shaft assembly
2. Steering lower shaft assembly lower joint bolt
3. Steering shaft joint
STEERING WHEEL AND COLUMN 3C-11
STEERING LOWER SHAFT ASSEMBLY
REMOVAL
1) Turn steering wheel so that vehicle's front tires are at straight-
ahead position.
2) Turn ignition switch to ªLOCKº position and remove key.
3) Make alignment marks on shaft joint and shaft (column side) for
a guide during reinstallation.
4) After removing bolt on column side of shaft joint and loosening
bolt on its lower shaft assembly side, move shaft joint to lower
shaft assembly side (in arrow direction in figure).
5) Make alignment marks on lower shaft assembly lower joint and
pinion shaft for a guide during reinstallation.
6) Remove lower shaft assembly lower joint bolt and then remove
lower shaft assembly.
7) Remove shaft joint bolt (lower shaft assembly side) from shaft
joint and then remove shaft joint from lower shaft assembly.

YH4
GRAND
VITARA
3C1
AIR BAG STEERING WHEEL AND COLUMN 3C1-1
GENERAL DESCRIPTION3C1- 2 . . . . . . . . . . . . .
DIAGNOSIS3C1- 3 . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair Required after
Accident 3C1- 3. . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE3C1- 3 . . . . . . . . . . . . . . .
Service Precautions 3C1- 3. . . . . . . . . . . . . . . . .
Diagnosis and Servicing 3C1- 3. . . . . . . . . . . .
Disabling Air Bag System 3C1- 3. . . . . . . . . . .
Enabling Air Bag System 3C1- 3. . . . . . . . . . .
Handling and Storage 3C1- 3. . . . . . . . . . . . . .
Disposal 3C1- 3. . . . . . . . . . . . . . . . . . . . . . . . . .
Driver Air Bag (Inflator) Module 3C1- 4. . . . . . . .
Steering Wheel 3C1- 6. . . . . . . . . . . . . . . . . . . . . . Centering Contact Coil 3C1- 6. . . . . . . . . . . . .
Contact Coil and Combination Switch
Assembly 3C1- 7. . . . . . . . . . . . . . . . . . . . . . . . .
Steering Column 3C1- 9. . . . . . . . . . . . . . . . . . . .
Steering Lock Assembly (Ignition
Switch) 3C1-14. . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering Lower Shaft Assembly 3C1-15. . . . . . .
Checking Steering Column for Accident
Damage 3C1-17. . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustable Steering Column Release
Lever 3C1-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS3C1-18 . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL3C1-18 . . . . . . . . . . . . . . . . . . . . . .
SECTION 3C1
AIR BAG STEERING WHEEL AND COLUMN
WARNING:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Please observe all WARNINGS and ªService Precautionsº under ªOn-Vehicle
Serviceº in air bag system section before performing service on or around the air bag system compo-
nents or wiring. Failure to follow WARNINGS could result in unintentional activation of the system
or could render the system inoperative. Either of these two conditions may result in severe injury.

The procedures in this section must be followed in the order listed to disable the air bag system tem-
porarily and prevent false diagnostic trouble codes from setting. Failure to follow procedures could
result in possible activation of the air bag system, personal injury or otherwise unneeded air bag sys-
tem repairs.
CAUTION:
When fasteners are removed, always reinstall them at the same location from which they were re-
moved. If a fastener needs to be replaced, use the correct part number fastener for that application. If
the correct part number fastener is not available, a fastener of equal size and strength (or stronger) may
be used. Fasteners that are not reused, and those requiring thread-locking compound, will be called
out. The correct torque value must be used when installing fasteners that require it. If the above proce-
dures are not followed, parts or system damage could result.
CONTENTS

YH4
GRAND
VITARA
14
15
1. Driver air bag (inflator) module
2. Steering wheel
3. Steering wheel nut
4. Contact coil and combination switch assembly
5. Steering column upper cover
6. Steering column lower cover
7. Steering column assembly
8. Steering lock assembly
9. Steering column hole cover
10. Steering shaft joint
11. Steering lower shaft assembly
12. Adjustable steering column release lever
(if equipped)
13. Steering column lower seal
14. With adjustable steering column release lever type
15. Without adjustable steering column release lever type
3C1-2 AIR BAG STEERING WHEEL AND COLUMN
GENERAL DESCRIPTION
This double tube type steering column has the following three important features in addition to the steering function:

The column is energy absorbing, designed to compress in a front-end collision.

The ignition switch and lock are mounted conveniently on this column.

With the column mounted lock, the ignition and steering operations can be locked to inhibit theft of the vehicle.
To insure the energy absorbing action, it is important that only the specified screws, bolts, and nuts be used as
designated and that they are tightened to the specified torque. When the column assembly is removed from the
vehicle, special care must be taken in handling it. Use of a steering wheel puller other than the one recommended
in this manual or a sharp blow on the end of the steering shaft, leaning on the assembly, or dropping the assembly
could shear the plastic shear pins which maintain column length and position.
The driver air bag (inflator) module is one of the supplemental restraint (air bag) system components and is
mounted to the center of the steering wheel. During certain frontal crashes, the air bag system supplements the
restraint of the driver's and passenger's seat belts by deploying the air bags. The air bag (inflator) module should
be handled with care to prevent accidental deployment. When servicing, be sure to observe all WARNINGS in this
section. Refer to ªSERVICE PRECAUTIONSº in Section 10B.

YH4
GRAND
VITARA
(A)
1
1. Make alignment marks
1. Steering wheel
Turn slowly till coil stops
Turn contact coil back about 2 and
a half turns
1. Align marks
3C1-6 AIR BAG STEERING WHEEL AND COLUMN
STEERING WHEEL
CAUTION:
Removal of the steering wheel allows the contact coil to turn
freely but do not turn the contact coil (on the combination
switch) more than allowable number of turns (about two and
a half turns from the center position clockwise or counter-
clockwise respectively), or coil will break.
REMOVAL
1) Remove driver air bag (inflator) module from steering wheel re-
ferring to ªDRIVER AIR BAG (INFLATOR) MODULEº earlier in
this section.
2) Remove steering shaft nut.
3) Make alignment marks on steering wheel and shaft for a guide
during reinstallation.
4) Remove steering wheel with special tool.
Special Tool
(A): 09944-36011
CAUTION:
Do not hammer the end of the shaft. Hammering it will
loosen the plastic shear pins which maintain the column
length and impair the collapsible design of the column.
CENTERING CONTACT COIL
1) Check that vehicle's wheels (front tires) are set at straight-ahead
position.
2) Check that ignition switch is at ªLOCKº position.
3) Turn contact coil counterclockwise slowly with a light force till
contact coil will not turn any further.
NOTE:
Contact coil can turn about 5 turns at maximum, that is, if
it is at the center position, can turn about two and a half
turns both clockwise and counterclockwise.
4) From the position where contact coil became unable to turn any
further (it stopped), turn it back clockwise about two and a half
rotations and align center mark with alignment mark.

YH4
GRAND
VITARA
1
1. Lugs
2. Grooves
3. Alignment marks
2. Steering column upper cover
3. Steering column lower cover 1. Steering column
cover screw
(a)
1. Steering column hole cover
AIR BAG STEERING WHEEL AND COLUMN 3C1-7
INSTALLATION
1) Check that vehicle's front tires are at straight-ahead position and
contact coil is centered. Refer to ªCENTERING CONTACT
COILº in this section.
CAUTION:
These two conditions are prerequisite for installation of
steering wheel. If steering wheel has been installed with-
out these conditions, contact coil will break when steer-
ing wheel is turned.
2) Install steering wheel to steering shaft with 2 lugs on contact coil
fitted in two grooves in the back of steering wheel and also align-
ing marks on steering wheel and steering shaft.
3) Tighten steering shaft nut to specified torque.
Tightening Torque
(a): 33 N
.m (3.3 kg-m, 23.5 lb-ft)
4) Install driver air bag (inflator) module to steering wheel. Refer to
ªDRIVER AIR BAG (INFLATOR) MODULEº in this section.
CONTACT COIL AND COMBINATION SWITCH
ASSEMBLY
CAUTION:
Do not turn contact coil (on combination switch) more than
allowable number of turns (about two and a half turns from
the center position clockwise or counterclockwise respec-
tively), or coil will break.
REMOVAL
1) Remove steering wheel from steering column. Refer to
ªSTEERING WHEELº in this section.
2) Remove steering column hole cover.
3) Remove steering column cover screws (3 pieces).
4) Separate upper cover and lower cover, then remove them.
5) Disconnect all connectors for contact coil and combination
switch assembly.