2004 SUZUKI GRAND VITARA change

YH4
GRAND
VITARA
7D
TRANSFER 7D-1
The aluminum transfer case directly connected to the
back of the transmission contains the input gear,
countershaft & gear, output rear shaft, output low gear
and output front shaft (for front drive) connected by
way of the hyvo-chain.
The transfer has such a selective mechanism as to
enable the shift control lever to make selection of high
speed (direct connection with transmission output:
main shaft), low speed (speed reduction by input
gear, counter gear and output low gear) or neutral by
way of the reduction sleeve located between input
gear and output low gear, and selection of two-wheel-
drive (high speed only) or four-wheel-drive (high or
low speed) by way of the front drive clutch sleeve lo-cated at the center of the output rear shaft. Also, with
a synchronizer installed to the front drive clutch, it is
possible to change the drive mode between 2WD
(high speed only) and 4WD (high speed only) even
while running.
The front drive shift fork has an auxiliary spring to
make a smooth shift from 4H to 2H possible.
The case has an oil gutter and a plate at synchronizer
to provide proper lubrication even under the strict
conditions of use.
WARNING:
For towing the vehicle for the purpose of repair or
the like, follow the towing instructions in OWN-
ER'S MANUAL.
SECTION 7D
TRANSFER
CONTENTS
GENERAL DESCRIPTION7D-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS7D-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table7D-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gear Oil7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Oil Seals7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer Driven Gear7D-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting7D-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Assembly7D-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dismounting7D-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remounting7D-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION

YH4
GRAND
VITARA
7D-2 TRANSFER
DIAGNOSIS
DIAGNOSIS TABLE
Before attempting to repair the transfer or related components for any reason other than mechanical failure, the
condition and probable causes should be identified.
Transfer failures are revealed by shifting difficulties such as excessive shifting effort, gear clash, or gear grinding.
When any of these conditions occur, the following inspections should be made before disassembling the transfer.
1) Check transfer oil level for insufficient or incorrect oil. Refer to ªTransfer and Differential Oil Inspection and
Changeº in SECTION 0B ªMAINTENANCE AND LUBRICATIONº.
2) Check transfer mountings for wear or looseness.
3) Check gearshift control lever for distortion or excessive wear.
After performing the above inspections, refer to following diagnosis table.
Condition
Possible CauseCorrection
Gear slipping out of mesh
Worn shift fork shaft

Worn shift fork or synchronizer sleeve

Weak or damaged locating spring

Worn bearings on output rear shaft

Worn chamfered tooth on sleeve or gear

Missing or disengagement of circlip(s)Replace
Replace
Replace
Replace
Replace sleeve and gear
Install
Gears refusing to disengage
Weakened or broken synchronizer spring

Distorted shift shaft or shift forkReplace
Replace
Hard shifting
Weakened front drive shift shaft spring

Distorted or mispositioned front drive shift
shaft circlip and washer

Inadequate or insufficient lubricant

Worn synchronizer ring

Worn chamfered tooth on sleeve or gear

Distorted shift shaftReplace
Replace
Replenish
Replace
Replace sleeve and gear
Replace
Noise
Inadequate or insufficient lubricant

Damaged or worn bearing(s)

Damaged or worn gear(s)

Damaged or worn synchronizer ring

Damaged or worn chamfered tooth on
sleeve or gearReplenish
Replace
Replace
Replace
Replace

YH4
GRAND
VITARA
7E
DIFFERENTIAL (FRONT) 7E-1
The differential assembly using a hypoid bevel pinion
and gear is installed to the front axle.
4WD control system controls drive force to be trans-
mitted to front axles or not. The reduction ratio varies
depending on transmission or engine type.The differential assembly is decisive in that the drive
power is concentrated there. Therefore, use of genu-
ine parts and specified torque is compulsory. Further,
because of sliding tooth meshing with high pressure
between bevel pinion and gear, it is mandatory to lu-
bricate them by hypoid gear oil.
SECTION 7E
DIFFERENTIAL (FRONT)
CONTENTS
GENERAL DESCRIPTION7E- 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4WD CONTROL SYSTEM7E- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS7E- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS TABLE7E- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential Assembly7E- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4WD Control System Diagnostic Flow Table 7E- 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4WD CONTROL CIRCUIT INSPECTION 7E- 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7E- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE SERVICE7E- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gear Oil Change7E- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSPECTION7E-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4WD Control System7E-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Actuator7E-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Pump Assembly7E-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION 7E-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential Mountings7E-13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DISMOUNTING7E-15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOUNTING7E-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7E-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS7E-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIAL7E-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS7E-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION

YH4
GRAND
VITARA
DIFFERENTIAL (FRONT) 7E-9
Viscosity chart SAE
Temperature
ON-VEHICLE SERVICE
MAINTENANCE SERVICE
NOTE:

When having driven through water, check immediately if wa-
ter has entered (if so, oil is cloudy). Water mixed oil must be
changed at once.

Whenever vehicle is hoisted for any other service work than
oil change, also be sure to check for oil leakage and status
of breather hoses.
Gear Oil Change
NOTE:

Hypoid gear oil must be used for differential.

It is highly recommended to use SAE 80W ± 90 viscosity.
1) Before oil change or inspection, be sure to stop engine and lift
up vehicle horizontally.
2) Check oil level and existence of leakage. If leakage is found, cor-
rect its cause.
3) Drain old oil and pour proper amount of gear oil as specified be-
low (roughly up to level hole).
4) Apply sealant to thread of drain plug (b) and torque plugs to
specification.
Sealant 99000-31110
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
(b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
Specified gear oil: Hypoid gear oil API GL-5
SAE 75W ± 85, 90 or 80W ± 90
For oil viscosity, refer to left chart.
Oil capacity: 1.0 liters (2.1 / 1.8 US / lmp. pt)

YH4
GRAND
VITARA
1. Breather hose
2. Oil filler / level plug
3. Rear drain plug
(Apply sealant)
Viscosity chart SAE
DIFFERENTIAL (REAR) 7F-3
ON-VEHICLE SERVICE
MAINTENANCE SERVICE
NOTE:

When having driven through water, check immediately if wa-
ter has entered (if so, oil is cloudy). Water mixed oil must be
changed at once.

Whenever vehicle is hoisted for any other service work than
oil change, also be sure to check for oil leakage and status
of breather hoses.
CHANGING OIL
NOTE:

Hypoid gear oil must be used for differential.

It is highly recommended to use SAE 80W-90 viscosity.
1) Before oil change or inspection, be sure to stop engine and lift
up vehicle horizontally.
2) Check oil level and existence of leakage. If leakage is found, cor-
rect its cause.
3) Drain old oil and pour proper amount of gear oil as specified
(roughly up to level hole).
4) Torque drain and level / filler plugs to specification.
ªAº: Sealant 99000-31110
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
(b): 28 N
.m (2.8 kg-m, 20.5 lb-ft)
Specified gear oil: Hypoid gear oil API GL-5
SAE 75W-85, 80W-90 or 90
For oil viscosity, refer to the chart
at the left.
Oil capacity : 2.2 liters (4.6 / 3.9 US / Imp. pt.)

YH4
GRAND
VITARA
WASHER
ONON
OFF
10 ± 14V
0VApprox. 2.5 sec.
Approx. 0.5 sec.
8D-12 WINDOWS, MIRRORS, SECURITY AND LOCKS
Washer Linked Operation
1) Disconnect negative cable at battery.
2) Disconnect combination switch lead wire coupler.
3) Make sure that front wiper switch is at OFF position.
4) Connect battery positive terminal to terminal ªB3º and battery
negative terminal to terminal ªEº.
5) Connect voltmeter positive lead to terminal ª+1º and negative
lead to terminal ªEº.
6) Pull washer switch and check that voltage changes as shown in
the table.
Washer switch
Voltmeter

YH4
GRAND
VITARA
8D-14 WINDOWS, MIRRORS, SECURITY AND LOCKS
2) TESTING AUTOMATIC STOP ACTION
a) First, connect battery (+) terminal to terminal ªDº and battery
(±) terminal to black lead wire (2) and let the motor (1) turn.
b) Then disconnect terminal ªDº from battery and let the motor
stop.
c) Next connect terminal ªDº and terminal ªAº with a jumper wire
(3) and connect terminal ªBº to battery (+) terminal. Observe the
wiper motor turns once again, then stops at a given position.
d) Repeat these steps several times, and inspect if the motor
stops at the given position every time.
Rear Wiper Intermittent Relay
[ON circuit]
1) Connect positive terminal of battery to terminals ª1º and ª4º of
relay, negative terminal to terminal ª5º of relay and check voltage
between terminals ª6º and ª5º of relay.
If measured voltage is battery voltage, relay is in good condition.
If not, replace relay.
2) Connect positive terminal of battery to terminal ª2º of relay, then
disconnect positive terminal from terminal ª4º of relay and check
voltage between terminals ª6º and ª5º of relay.
If measured voltage is battery voltage, relay is in good condition.
If not, replace relay.
3) Disconnect positive terminal from terminal ª2º of relay and check
voltage between terminals ª6º and ª5º of relay.
If measured voltage is about 0 V, relay is in good condition.
If not, replace relay.
[WASH circuit]
1) Connect positive terminal of battery to terminal ª1º of relay and
negative terminal to terminal ª5º of relay. Then connect positive
terminal to terminal ª7º checking voltage between terminals ª6º
and ª5º of relay.
If measured voltage changes from about 0 V to battery voltage
0.6 to 1.5 seconds after connecting positive terminal to terminal
ª7º, relay is in good condition. If not, replace relay.

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-15
2) Disconnect positive terminal from terminal ª7º checking voltage
between terminal ª6º and ª5º of relay.
If measured voltage changes from battery voltage to about 0 V
2.7 to 4.6 seconds after disconnecting positive terminal from ter-
minal ª7º, relay is in good condition.
If not, replace relay.
[INT circuit]
1) Connect positive terminal of battery to terminals ª1º of relay and
negative terminal to terminal ª5º of relay. Then positive terminal
to terminal ª3º of relay checking voltage between terminals ª6º
and ª5º of relay.
If measured voltage changes from about 0 V to battery voltage
when connecting positive terminal to terminal ª3º, relay is in
good condition.
If not, replace relay.
2) Connect positive terminal of battery to terminal ª2º of relay, then
disconnect positive terminal from terminal ª2º of relay checking
voltage between terminals ª6º and ª5º of relay.
If measured voltage changes from battery voltage to about 0 V
when disconnecting positive terminal from terminal ª2º and
about 0 V to battery voltage 8
2 seconds after disconnecting
positive terminal from terminal ª2º, relay is in good condition.
If not, replace relay.