2004 SUZUKI GRAND VITARA change

YH4
GRAND
VITARA
7B1-4 AUTOMATIC TRANSMISSION (4 A / T)
ItemSpecifications
Torque
conver-
terType
Stall torque ratio3-element, 1-step, 2-phase type (with TCC (lock-up)
mechanism)
2.4 (G16 engine) 2.0 (J20 engine) 1.9 (H25 engine)
Oil
pumpType
Drive systemTrochoid type oil pump
Engine driven
TypeForward 4-step, reverse 1-step planetary gear type
Shift position
ªPº range Gear in neutral, output shaft fixed,engine start
ªRº range Reverse
ªNº range Gear in neutral, engine start
ªDº range Forward 1st
2nd
3rd
4th (O / D)
(O / D ON) automatic gear change
ªDº range Forward 1st
2nd
3rd
(O / D OFF) automatic gear change
ª2º range (Normal mode) Forward 1st
2nd  3rd automatic gear
change
(Power mode) Forward 2nd  3rd automatic gear
change and fixed at 2nd gear
ªLº range Forward 1st  2nd  3rd reduction, and fixed at 1st gear
GearEngine typeG16 engineJ20 / H25 engines
change
device1st (low gear)2.8262.826device2nd (second gear)1.4931.493
Gear3rd (top gear)1.0001.000Gear
ratio4th (overdrive
4th gear)0.7300.689
Reverse (reverse
Reverse gear)2.7032.703
Control elements
Wet type multi-disc clutch 3 sets. . . . . . . . . .
Wet type multi-disc brake 4 sets. . . . . . . . . .
One-way clutch 3 sets. . . . . . . . . . . . . . . . . . .
TransferHi: 1.000 Lo: 1.816 (4WD model only)
Final gear reduction
ratio (Differential)5.125 (G16 engine) 4.875 (J20 / H25 engines)
Lubrica-
tionLubrication systemForce feed system by oil pump
CoolingCooling systemRadiator assisted cooling (water-cooled)
Fluid usedAn equivalent of DEXRON
III

YH4
GRAND
VITARA
Engine
Vehicle speed
sensor
Throttle position
sensor
ECT sensor
Cruise control
module
(if equipped)Torque converter Planetary gear
Final gear
reduction unit
Oil pump
Shift and TCC
solenoid valvesClutch and brake
Control valve
ªO / D OFFº lamp
ªPOWERº lamp
MILTransmission range
switch
O / D cut switch
P / N change switch
Transfer 4L switch
(if equipped)
CMP sensor Powertrain (engine) control module
Power transmission
Fluid pressure circuit
Electric signalInput speed sensor Brake pedal switch
Output speed sensor
AUTOMATIC TRANSMISSION (4 A / T) 7B1-7
ELECTRONIC SHIFT CONTROL SYSTEM
The gear ratio change in ªDº or ª2º range and torque converter clutch operation are controlled by Powertrain (En-
gine) Control Module.

YH4
GRAND
VITARA
7B1-8 AUTOMATIC TRANSMISSION (4 A / T)
G16 / J20 Engines
1. PCM (ECM)
2. VSS
3. CMP sensor
4. TP sensor
5. ECT sensor
6. A / T input speed sensor
7. A / T output speed sensor
8. Transmission range switch9. Shift solenoid-A
10. Shift solenoid-B
11. TCC solenoid
12. Data link connector
13. Cruise control module
14. ªPOWERº lamp
15. ªO / D OFFº lamp
16. MIL17. O / D cut switch
18. P / N change switch
19. 4WD low switch
20. Main relay
21. Ignition switch
22. Battery
23. PCM (ECM) connector terminal
(viewed from harness side) Bl / Y
Bl / G
W
OrC51-1-11
C51-1-10
C51-1-23
C51-1-22
12V

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-9
H25 Engine
1. PCM (ECM)
2. VSS
3. CMP sensor
4. TP sensor
5. ECT sensor
6. Brake pedal switch
7. A / T input speed sensor
8. A / T output speed sensor9. Transmission range switch
10. Shift solenoid-A
11. Shift solenoid-B
12. TCC solenoid
13. Data link connector
14. Cruise control module
15. ªPOWERº lamp
16. ªO / D OFFº lamp17. MIL
18. O / D cut switch
19. P / N change switch
20. 4WD low switch
21. Main relay
22. Ignition switch
23. Battery
24. PCM (ECM) connector terminal
(viewed from harness side) Bl / Y
Bl / G
W
OrC51-1-16
C51-1-8
C51-1-10
C51-1-9
12V

YH4
GRAND
VITARA
7B1-10 AUTOMATIC TRANSMISSION (4 A / T)
Shift the select
lever with its
button pushed
in.
Shift the select
lever without
pushing its
button.
RANGE
GEAR
SOLENOIDS
Fail Safe Function
This function is provided by the safe mechanism that assures safe driveability even when the shift solenoid valve
or speed sensor fails.
The table below shows the gear position in each shift under a normal/abnormal condition.
Condition
Shift position
Normal
Shift solenoid
valve-A(#1)
abnormalShift solenoid
valve-B(#2)
abnormalShift solenoid
valves-A&B
(#1 and #2) abnormal
1st1st
D2nd3rdO/DD3rdO/DO/D
O/DO/D
1st1st
22nd3rd3rd3rd
(3rd)3rd
L1st1st1st1stL(2nd)(2nd)1st1st
Change Mechanism
The same select pattern shift lever is used as the floor type and fre-
quently used ªNº and ªDº ranges are made selectable freely.
Operation of Shift Solenoids and TCC Solenoid
D2LP, N & R
1st2nd3rd4th
(O / D)1st2nd1stÐ
Shift solenoid-A (#1, NO.1)








Shift solenoid-B (#2, NO.2)








TCC solenoid









: ON (valve is open)
: OFF (valve is closed)

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-23
User name: Model: VIN:
Date of issue: Date of Reg: Date of problem: Mileage:
PROBLEM SYMPTOMS
Engine does not start
Vehicle does not move
(forward, rearward)
No lock-up (TCC clutch operation)
Shift point too high or too low
Excessive gear change shockEngine stops
Transmission does not shift
(1st, 2nd, 3rd, 4th, Rev) gear
Automatic shift does not occur
Transmission slipping in
(1st, 2nd, 3rd, 4th, Rev) gear
Other:
VEHICLE/ ENVIRONMENTAL CONDITION WHEN PROBLEM OCCURS
Environmental Condition
Weather
Temperature
Frequency
RoadFair/Cloudy/Rain/Snow/Always/Other ( )
Hot/Warm/Cool/Cold/(
C
F)/Always
Always/Sometimes/( times/ day, month)/Only Once
Urban/Suburb/Highway/Mountainous (uphill/downhill)/Paved road/Gravel/
Other( )
Vehicle Condition
Engine
Brake
O/D cut switch
P/N change switch
(P,R,N,D,2,L) range/(
) range
Cold/Warming up phase/Warmed up
At stop/During driving (constant speed/accelerating/decelerating/
right hand corner/left hand corner)/Other ( )/Speed ( km/h mile/h)
Speed( r/min)/Throttle opening(idle/about %/full)
Apply/Not apply
ON/OFF
Power/Normal
Malfunction indicator lamp condition
Always ON Sometimes ON Always OFF Good condition
Diagnostic trouble
codeFirst check : No codeMalfunction code( )
Second check : No code Malfunction code( )
Transmission range
Transmission temp.
Vehicle
CUSTOMER PROBLEM INSPECTION FORM (EXAMPLE)
NOTE:
The above form is a standard sample. It should be modified according to conditions characteristic of each
market.

YH4
GRAND
VITARA
7B1-24 AUTOMATIC TRANSMISSION (4 A / T)
MALFUNCTION INDICATOR LAMP (MIL) CHECK
Refer to the same item in Section 6 / 6-1 for checking procedure.
ªO / D OFFº LAMP CHECK
1) Check that O / D cut switch button is at OFF position (pushed).
2) Turn ignition switch ON.
3) Check that ªO / D OFFº lamp lights for about 2 ± 4 sec. and then goes OFF.
If anything faulty is found, advance ªDiagnostic flow table B-1 or B-2º O / D OFF ªLAMP CIRCUIT CHECKº.
ªPOWERº LAMP CHECK
1) Check that Power / Normal change switch button is at Normal position.
2) Turn ignition switch ON.
3) Check that ªPowerº Lamp light for 2 ± 4 sec. and then goes OFF.
If anything faulty is found, advance ªDiagnostic flow table B-3 or B-4 ªPOWERº LAMP CIRCUIT CHECK 2.
DIAGNOSTIC TROUBLE CODE (DTC) CHECK
Refer to the same item in Section 6 / 6-1 for checking procedure.
DIAGNOSTIC TROUBLE CODE (DTC) CLEARANCE
Refer to the same item in Section 6 / 6-1 for clearance procedure.
DIAGNOSTIC TROUBLE CODE (DTC) TABLE (A / T RELATED CODE)
DTC NO.MIL
Using
scan toolNot using
scan toolDETECTED ITEMDETECTING CONDITION
Vehicle
without
monitor
connectorVehicle
with
monitor
connector
±12±No trouble.±±
P070572Transmission range
sensor circuit
Multiple signals inputted simulta-
neously or no signal inputted while
2 driving
cycles
Not
applicablesensor circuit
malfunction
neously or no signal in utted while
running at 60 km / h or more.
cyclesa licable
P071576Input / Turbine speed
sensor circuit
malfunctionInput shaft revolution speed is lower
than specified value while
vehicle is running with ªDº range and
specified engine speed or higher.2 driving
cyclesNot
applicable
P072075Output speed sensor
circuit malfunctionOutput speed sensor signal not
inputted while VSS signal being
inputted.2 driving
cyclesNot
applicable
*1
P0741
Not
applicableTCC (lock-up) solenoid
performance or stack
offActual TCC operation does not
agree with ON / OFF control from
PCM to TCC.2 driving
cyclesNot
applicable
P074365
66TCC (lock-up)
solenoid electricalMonitor signal OFF is detected
When TCC control solenoid is ON or
monitor signal ON is detected when
it is OFF.1 driving
cycleNot
applicable
*1
P0751
Not
applicableShift solenoid A (#1)
performance or stuck
offGear change control from PCM to
A / T does not agree with actual gear
position of A / T.2 driving
cyclesNot
applicable
P075361
62Shift solenoid A (#1)
electricalMonitor signal OFF is detected
when shift solenoid A (#1) is ON or
monitor signal ON is detected when
it is OFF.1 driving
cycleNot
applicable

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-25
DIAGNOSTIC TROUBLE CODE (DTC) TABLE (A / T RELATED CODE) (cont'd)
DTC NO.MIL
Using
scan toolNot using
scan toolDETECTED ITEMDETECTING CONDITION
Vehicle
without
monitor
connectorVehicle
with
monitor
connector
*1
P0756
Not
applicableShift solenoid B (#2)
performance or stuck
offGear change control from PCM to
A / T does not agree with actual gear
position of A / T.2 driving
cyclesNot
applicable
P075863
64Shift solenoid B (#2)
electricalMonitor signal OFF is detected
when shift solenoid B (#2) is ON or
monitor signal ON is detected when
it is OFF.1 driving
cycleNot
applicable
*1
P1875
Not
applicable4WD low switch circuit
malfunctionDifference between vehicle speed
detected by VSS and vehicle speed
detected by output speed sensor
and compensated by 4WD low
switch is larger than specification.2 driving
cyclesNot
applicable
NOTE:
*1: Applicable to vehicle without monitor connector only.
FAIL-SAFE TABLE
When any of the following DTC is detected, ECM (PCM) enters fail-safe mode as long as malfunction continues
to exist but that mode is canceled when ECM detects normal condition after that.
DTC NO.
Using
scan toolNot using
scan toolTROUBLE AREAFAIL SAFE OPERATION
P0177
P011814
15ECT SENSOR
Each control except 4-A / T is permitted on the basis of
30.1C engine coolant temp.

4-A / T control is performed assuming 31C (engine warmed
up) or higher after 15 min. from engine start.
P0122
P012321
22TP SENSOR
Each control except 4-A / T is performed on the basis of 124
throttle valve opening.

4-A / T control is performed on the basis of 0 throttle valve
opening.
P070572TR SWITCHA / T control is performed in priority order of L, 2, N, D, R
and P.
P072075OUTPUT SPEED
SENSOR CIRCUIT
MALFUNCTIONA / T control is performed by using signal from VSS.
P075361
62SHIFT SOLENOID
A (#1)
A / T control using 3rd gear is performed when D range, 1st
or 2nd gear is used.

TCC solenoid OFF.
P075863
64SHIFT SOLENOID
B (#2)
A / T control using 4th gear is performed when D range 2nd
or 3rd gear is used.

When both shift solenoid A (#1) and B (#2) failed
simultaneously, A / T control using 4th gear is always
performed in D range.

TCC solenoid OFF.
P074365
66TCC (Lock-up)
SOLENOIDTCC (lock-up) solenoid OFF.