2004 SUZUKI GRAND VITARA length

YH4
GRAND
VITARA
1. Steering column
2. Steering column mounting bolt
3. Steering column lower seal
1. Shift (key) interlock cable
2. Screw
1. Capsule
2. Steering column bracket
3. Plate
1. Steering column assembly ªaº
STEERING WHEEL AND COLUMN 3C-7
7) Remove steering column mounting bolts (6 pieces).
8) If equipped with shift (key) interlock cable, remove shift (key) in-
terlock cable screw and then disconnect its cable from ignition
switch.
9) Remove steering column from vehicle.
INSPECTION
NOTE:
Vehicles involved in accidents resulting in body damage,
where steering column has been impacted or air bag
deployed, may have a damaged or misaligned steering col-
umn.
CHECKING PROCEDURE
1) Check that two capsules are attached to steering column brack-
et securely. Check clearance between capsules and steering
column bracket. Clearance should be 0 mm (0 in.) on both sides.
If found loose or clearance, replace steering column assembly.
2) Check two plates for any damages such as crack or breakage.
If anything is found faulty, replace as steering column assembly.
3) Take measurement ªaº as shown. If it is shorter than specified
length, replace column assembly with new one.
Length ªaº: 895
0.8 mm (35.24
0.03 in.)

YH4
GRAND
VITARA
STEERING WHEEL AND COLUMN 3C-13
1. Capsule
2. Steering column bracket
3. Plate
1. Steering column assembly
1. Steering column lower seal ªaº
CHECKING STEERING COLUMN FOR
ACCIDENT DAMAGE
NOTE:
Vehicles involved in accidents resulting in body damage,
where steering column has been impacted, may have a dam-
aged or misaligned steering column.
CHECKING PROCEDURE
1) Check that two capsules are attached to steering column brack-
et securely. Check clearance between capsules and steering
column bracket. Clearance should be 0 mm (0 in.) on both sides.
If found loose or clearance, replace steering column assembly.
2) Check two plates for any damages such as crack or breakage.
If anything is found faulty, replace as steering column assembly.
3) Take measurement ªaº as shown. If it is shorter than specified
length, replace column assembly with new one.
Length ªaº: 895
0.8 mm (35.24
0.03 in.)
4) Check steering column lower seal for breakage or deformation.
If found defective, replace.
5) Check steering shaft joints and shaft for any damages such as
crack, breakage, malfunction or excessive play.
If anything is found faulty, replace as steering shaft lower assem-
bly or steering column assembly.
6) Check steering shaft for smooth rotation.
If found defective, replace as column assembly.
7) Check steering shaft and column for bend, cracks or deforma-
tion.
If found defective, replace as column assembly.

YH4
GRAND
VITARA
14
15
1. Driver air bag (inflator) module
2. Steering wheel
3. Steering wheel nut
4. Contact coil and combination switch assembly
5. Steering column upper cover
6. Steering column lower cover
7. Steering column assembly
8. Steering lock assembly
9. Steering column hole cover
10. Steering shaft joint
11. Steering lower shaft assembly
12. Adjustable steering column release lever
(if equipped)
13. Steering column lower seal
14. With adjustable steering column release lever type
15. Without adjustable steering column release lever type
3C1-2 AIR BAG STEERING WHEEL AND COLUMN
GENERAL DESCRIPTION
This double tube type steering column has the following three important features in addition to the steering function:

The column is energy absorbing, designed to compress in a front-end collision.

The ignition switch and lock are mounted conveniently on this column.

With the column mounted lock, the ignition and steering operations can be locked to inhibit theft of the vehicle.
To insure the energy absorbing action, it is important that only the specified screws, bolts, and nuts be used as
designated and that they are tightened to the specified torque. When the column assembly is removed from the
vehicle, special care must be taken in handling it. Use of a steering wheel puller other than the one recommended
in this manual or a sharp blow on the end of the steering shaft, leaning on the assembly, or dropping the assembly
could shear the plastic shear pins which maintain column length and position.
The driver air bag (inflator) module is one of the supplemental restraint (air bag) system components and is
mounted to the center of the steering wheel. During certain frontal crashes, the air bag system supplements the
restraint of the driver's and passenger's seat belts by deploying the air bags. The air bag (inflator) module should
be handled with care to prevent accidental deployment. When servicing, be sure to observe all WARNINGS in this
section. Refer to ªSERVICE PRECAUTIONSº in Section 10B.

YH4
GRAND
VITARA
(A)
1
1. Make alignment marks
1. Steering wheel
Turn slowly till coil stops
Turn contact coil back about 2 and
a half turns
1. Align marks
3C1-6 AIR BAG STEERING WHEEL AND COLUMN
STEERING WHEEL
CAUTION:
Removal of the steering wheel allows the contact coil to turn
freely but do not turn the contact coil (on the combination
switch) more than allowable number of turns (about two and
a half turns from the center position clockwise or counter-
clockwise respectively), or coil will break.
REMOVAL
1) Remove driver air bag (inflator) module from steering wheel re-
ferring to ªDRIVER AIR BAG (INFLATOR) MODULEº earlier in
this section.
2) Remove steering shaft nut.
3) Make alignment marks on steering wheel and shaft for a guide
during reinstallation.
4) Remove steering wheel with special tool.
Special Tool
(A): 09944-36011
CAUTION:
Do not hammer the end of the shaft. Hammering it will
loosen the plastic shear pins which maintain the column
length and impair the collapsible design of the column.
CENTERING CONTACT COIL
1) Check that vehicle's wheels (front tires) are set at straight-ahead
position.
2) Check that ignition switch is at ªLOCKº position.
3) Turn contact coil counterclockwise slowly with a light force till
contact coil will not turn any further.
NOTE:
Contact coil can turn about 5 turns at maximum, that is, if
it is at the center position, can turn about two and a half
turns both clockwise and counterclockwise.
4) From the position where contact coil became unable to turn any
further (it stopped), turn it back clockwise about two and a half
rotations and align center mark with alignment mark.

YH4
GRAND
VITARA
1
1. Steering column hole cover 1. Steering column cover screw
2. Steering column upper cover
3. Steering column lower cover: Standard screw
: Tapping screw
*
* *
AIR BAG STEERING WHEEL AND COLUMN 3C1-9
3) Connect all connectors that have been removed in removal.
4) Install steering column upper and lower cover, and then tighten
steering column cover screws.
CAUTION:
When installing lower cover and upper cover, be careful
so that contact coil and combination switch lead wire is
not caught between covers.
5) Install steering column hole cover.
6) Install steering wheel to steering column. Refer to ªSTEERING
WHEELº in this section.
STEERING COLUMN
CAUTION:
Once the steering column is removed from the vehicle, the
column is extremely susceptible to damage.
Dropping the column assembly on its end could collapse
the steering shaft or loosen the plastic shear pins which
maintain column length leaning on the column assembly
could cause it to bend or deform.
Any of the above damage could impair the column's col-
lapsible design.
When loosening steering column mounting bolts, make
sure that steering column assembly and steering shaft low-
er assembly have been separated. Loosening them with
steering column assembly and steering shaft lower assem-
bly assembled could cause damage to bearing in steering
shaft lower assembly.
NOTE:
When servicing steering column or any column-mounted
component, remove steering wheel. But when removing steer-
ing column simply to gain access to instrument panel compo-
nents, leave steering wheel installed on steering column.

YH4
GRAND
VITARA
AIR BAG STEERING WHEEL AND COLUMN 3C1-11
1. Steering column
2. Steering column mounting bolt
3. Steering column lower seal
1. Shift (key) interlock cable
2. Screw
1. Capsule
2. Steering column bracket
3. Plate
1. Steering column assembly ªaº
8) Remove steering column mounting bolts (6 pieces).
9) If equipped with shift (key) interlock cable, remove shift (key)
interlock cable screw and then disconnect its cable from igni-
tion switch.
10) Remove steering column from vehicle.
INSPECTION
NOTE:
Vehicles involved in accidents resulting in body damage,
where steering column has been impacted or air bag
deployed, may have a damaged or misaligned steering col-
umn.
CHECKING PROCEDURE
1) Check that two capsules are attached to steering column brack-
et securely. Check clearance between capsules and steering
column bracket. Clearance should be 0 mm (0 in.) on both sides.
If found loose or clearance, replace steering column assembly.
2) Check two plates for any damages such as crack or breakage.
If anything is found faulty, replace as steering column assembly.
3) Take measurement ªaº as shown. If it is shorter than specified
length, replace column assembly with new one.
Length ªaº: 895
0.8 mm (35.24
0.03 in.)

YH4
GRAND
VITARA
AIR BAG STEERING WHEEL AND COLUMN 3C1-17
1. Capsule
2. Steering column bracket
3. Plate
1. Steering column assembly
1. Steering column lower seal ªaº
CHECKING STEERING COLUMN FOR
ACCIDENT DAMAGE
NOTE:
Vehicles involved in accidents resulting in body damage,
where steering column has been impacted or air bag
deployed, may have a damaged or misaligned steering col-
umn.
CHECKING PROCEDURE
1) Check that two capsules are attached to steering column brack-
et securely. Check clearance between capsules and steering
column bracket. Clearance should be 0 mm (0 in.) on both sides.
If found loose or clearance, replace steering column assembly.
2) Check two plates for any damages such as crack or breakage.
If anything is found faulty, replace as steering column assembly.
3) Take measurement ªaº as shown. If it is shorter than specified
length, replace column assembly with new one.
Length ªaº: 895
0.8 mm (35.24
0.03 in.)
4) Check steering column lower seal for breakage or deformation.
If found defective, replace.
5) Check steering shaft joints and shaft for any damages such as
crack, breakage, malfunction or excessive play.
If anything is found faulty, replace as steering shaft lower assem-
bly or steering column assembly.
6) Check steering shaft for smooth rotation.
If found defective, replace as column assembly.
7) Check steering shaft and column for bend, cracks or deforma-
tion.
If found defective, replace as column assembly.

YH4
GRAND
VITARA
1. Bearing retainer
2. Parking brake shoe
lever
3. Clearance1. Wheel speed sensor
1
L
REAR SUSPENSION 3E-11
4) Remove wheel speed sensor from rear axle housing (if
equipped with ABS).
CAUTION:

Do not pull wire harness or twist more than necessary
when removing rear wheel speed sensor.

Do not cause damage to surface of rear wheel speed
sensor or pole piece and do not allow dust, etc. to enter
its installation hole.
5) Check to ensure that there is clearance between rear wheel
bearing retainer and parking brake shoe lever. If no clearance
is found, loosen cable locking nut further to obtain clearance.
6) Using special tools (B) & (C) indicated below, draw out axle
shaft.
NOTE:
Use care not to pull brake back plate along with shaft.
CAUTION:
Pull out axle shaft using care so that upper and lower
brake struts and parking cable are not caught.
Special Tool
(C): 09943-35512
(B): 09942-15510
7) Rear axle shaft that was drawn out.
Shaft length ªLº:
Left side: 711.5 mm (28.0 in.)
Right side: 757.5 mm (29.8 in.)
8) If equipped with ABS, in order to remove sensor rotor from re-
tainer ring, grind with a grinder one part of the sensor rotor as
illustrated till it becomes thin.