Page 247 of 801
YH4
GRAND
VITARA
1. Axle housingªAº
(c)
1. Axle housing
3E-20 REAR SUSPENSION
7) For vehicle with ABS, connect wheel speed sensor coupler and
install harness.
8) Install propeller shaft and torque nuts to specification.
Tightening Torque
(b): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
9) Remove floor jack from axle housing and connect breather
hose onto axle housing and clamp it securely.
10) Connect brake pipes onto axle housing and clamp them se-
curely.
For clamping positions, refer to SECTION 5A of this manual.
11) Connect brake flexible hose to bracket on axle housing and se-
cure it with E-ring.
12) Install LSPV stay to axle housing, tighten LSPV stay bolt to
specified torque.
And adjust LSPV referring to ªLSPV ASSEMBLY INSPEC-
TION AND ADJUSTMENTº in SECTION 5A.
Tightening Torque
(c): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
13) Connect brake pipe to brake flexible hose and tighten brake
pipe flare nut to specified torque.
Tightening Torque
(d): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
14) Clean mating surface of axle housing (right & left) and brake
back plate, then apply sealant as shown.
ªAº: Sealant 99000-31110
15) Apply grease to axle shaft inner oil seal lip as shown.
ªAº: Grease 99000-25010
Page 348 of 801
YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-7
DIAGNOSIS
To ensure that the trouble diagnosis is done accurately and smooth-
ly, observe ªPrecautions in Diagnosing Troublesº and follow ªABS
Diagnostic Flow Tableº.
PRECAUTION IN DIAGNOSING TROUBLES
If the vehicle was operated in any of the following ways, ªABSº
warning light may light momentarily but this does not indicate any-
thing abnormal in ABS.
± The vehicle was driven with parking brake pulled.
± The vehicle was driven with brake dragging.
± The vehicle was stuck in mud, sand, etc.
± Wheel spin occurred while driving.
± Wheel(s) was rotated while the vehicle was jacked up.
Be sure to read ªPrecautions for Electronic Circuit Serviceº in
ªGENERAL INFORMATIONº section before inspection and ob-
serve what is written there.
Be sure to use the trouble diagnosis procedure as described in
the flow table. Failure to follow the flow table may result in incor-
rect diagnosis. (Some other diag. trouble code may be stored by
mistake in the memory of ABS control module during inspection.)
Page 364 of 801
YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-23
1. Ignition switch
2. ABS hydraulic unit /
control module assembly
3. Left-front wheel speed
sensor
4. Right-front wheel speed
sensor
5. Left-rear wheel speed
sensor
6. Right-rear wheel speed
sensor
7. ABS hydraulic unit /
control connector of harness
DTC 21 (DTC C1021), 22 (DTC C1022) ± RIGHT-FRONT WHEEL SPEED SENSOR
CIRCUIT
DTC 25 (DTC C1025), 26 (DTC C1026) ± LEFT-FRONT WHEEL SPEED SENSOR
CIRCUIT
DTC 31 (DTC C1031), 32 (DTC C1032) ± RIGHT-REAR WHEEL SPEED SENSOR
CIRCUIT
DTC 35 (DTC C1035), 36 (DTC C1036) ± LEFT-REAR WHEEL SPEED SENSOR
CIRCUIT
DESCRIPTION
The ABS control module monitors the voltage at the positive (+) terminal of each sensor while the ignition switch
is ON. When the voltage is not within the specified range, an applicable DTC will be set. Also, when no sensor signal
is inputted at starting or while running, an applicable DTC will be set.
NOTE:
When the vehicle was operated in any of the following ways, one of these DTC's may be set even when
the sensor is in good condition. If such possibility is suspected, repair the trouble (dragging of brake, etc.)
of the vehicle, clear DTC once and then after performing the driving test as described in Step 2 of ªABS
DIAG. FLOW TABLEº, check whether or not any abnormality exists.
± The vehicle was driven with parking brake pulled.
± The vehicle was driven with brake dragging.
± Wheel spin occurred while driving.
± Wheel(s) was turned while the vehicle was jacked up.
± The vehicle was stuck.