2004 SUZUKI GRAND VITARA Ignition switch
[x] Cancel search: Ignition switchPage 718 of 801
YH4
GRAND
VITARA
10B-12 AIR BAG SYSTEM
1. Data link connector (DLC)
2. DLC cable adapter
3. DLC cable
-1. ªAIR BAGº
warning lamp
-2. ªAIR BAGº fuse box
-3. ªAIR BAGº
monitor coupler
3-1. Diagnostic switch
terminal
-4. Air bag harness
(covered yellow tube)
EXAMPLE: When driver air bag initiator circuit resistance high (Code No.21) is set
Malfunction indicator lamp
(ªAIR BAGº warning lamp)
Turn ON
Turn OFF
Time (sec.) Code No. 21 Code No. 21 Code No. 21 1
DIAGNOSTIC TROUBLE CODE (DTC) CHECK
[Using SUZUKI scan tool]
1) Turn ignition switch OFF.
2) After setting cartridge to Tech 1, connect it to data link connector
(DLC) located on underside of instrument panel at driver's seat
side.
Special Tool
(A): 09931-76011 (Tech 1)
(B): Mass storage cartridge
(C): 09931-76030
3) Turn ignition switch ON.
4) Read DTC according to instructions displayed on Tech 1 and
print it or write it down. Refer to Tech 1 operator's manual for fur-
ther details.
5) After completing the check, turn ignition switch OFF and discon-
nect Tech 1 from data link connector (DLC).
[Not using SUZUKI scan tool]
1) Check that malfunction indicator lamp (ªAIR BAGº warning
lamp) comes ON when ignition switch is turned ON.
If it does not come ªONº, proceed to ªTable Bº on p.10B-18.
2) Using service wire, ground diagnosis switch terminal in monitor
coupler.
3) Read DTC from flashing pattern of malfunction indicator lamp
(ªAIR BAGº warning lamp). (Refer to ªDiagnostic Trouble Code
Tableº on p.10B-14 and 10B-15.)
4) After completing the check, turn ignition switch OFF and discon-
nect service wire from ªAIR BAGº monitor coupler.
Page 719 of 801
YH4
GRAND
VITARA
1. Data link connector
2. DLC cable adapter
3. DLC cable
1sec. 1sec.About 10 seconds
Open
Short-1. ªAIR BAGº warning lamp
-2. ªAIR BAGº fuse box
-3. ªAIR BAGº monitor coupler
3-1. Diagnostic switch terminal
-4. Air bag harness (covered yellow tube)1
AIR BAG SYSTEM 10B-13
DIAGNOSTIC TROUBLE CODE (DTC) CLEARANCE
[Using SUZUKI scan tool]
1) Turn ignition switch OFF.
2) Connect Tech 1 to data link connector (DLC) in the same manner
as when making this connection for DTC check.
Special Tool
(A): 09931-76011 (Tech 1)
(B): Mass storage cartridge
(C): 09931-76030
3) Turn ignition switch ON.
4) Erase DTC according to instructions displayed on Tech 1.
Refer to Tech 1 operator's manual for further details.
5) After completing the check, turn ignition switch OFF and discon-
nect Tech 1 from data link connector (DLC).
6) Perform ªDiagnosis Trouble Code (DTC) Checkº and confirm
that normal DTC (NO CODES) is displayed and not malfunction
DTC.
NOTE:
If DTC 51 or DTC 71 is stored in SDM, it is not possible to
clear DTC.
[Not using SUZUKI scan tool]
1) Turn ignition switch ON and wait about 6 seconds or more.
2) Using service wire, repeat shorting and opening between diag-
nosis switch terminal and ground terminal on ªAIR BAGº monitor
coupler 5 times at about 1 second intervals.
3) Perform ªDiagnosis Trouble Code (DTC) Checkº and confirm
that normal DTC (DTC 12) is displayed and not malfunction
DTC.
NOTE:
If DTC 51 or DTC 71 is stored in SDM, it is not possible to
clear DTC.
Page 721 of 801
YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-15
DIAGNOSTIC TROUBLE CODE TABLE (Page 2 of 2)
DIAGNOSTIC TROUBLE CODEDIAGNOSISNO.MODEDIAGNOSIS
41Resistance high
42Driver
pretensionerResistance low
43circuit
(if equipped)Short to ground
44Short to power circuit
45Resistance highDiagnose trouble
di t ªDi
46Passenger
pretensionerResistance low
according to ªDiagnos-
tic Flow Tableº corre-
sponding to each code
47circuit
(if equipped)Short to ground
s onding to each code
No.
48Short to power circuit
51SDMFrontal crash detected
61ªAIR BAGº warning lamp circuit
71SDMInternal fault
NOTE:
When 2 or more codes are indicated, the lowest numbered code will appear first.
If a code not listed on the table is displayed, then the SDM is faulty.
Current DTC and history DTC can be identified by lighting and flashing of ªAIR BAGº warning lamp as
follows.
Current DTC is set.
(Abnormality exists at present.)History DTC is set only. (Faulty condi-
tion occurred once in the past but nor-
mal condition is restored at present.)
ªAIR BAGº warning lamp
after ignition switch ONRemains ON.Flashing 6 times and turns OFF.
ªAIR BAGº warning lamp
when grounding diagnosis
switch
Current DTC is displayed.History DTC is displayed.
However, if a multiple number of DTC's are set an even one of them is a current DTC, ªAIR BAGº warning
lamp remains on after ignition switch is turned ON. Therefore, it is not possible to identify any of them
as to whether it is a current one or a history one. (But use of scan tool (Tech 1) will make identification
possible.)
Page 722 of 801
YH4
GRAND
VITARA
7. SDM
7-1. ªAIR BAGº warning lamp driver circuit 4. ªAIR BAGº warning lamp in combination meter
5. ªAIR BAGº fuse in ªAIR BAGº fuse box
6. Connection detection pin 1. From main fuse
2. Ignition switch
3. ªIG
.COIL METERº fuse in J/B: Air bag harness
10B-16 AIR BAG SYSTEM
TABLE A ± ªAIR BAGº WARNING LAMP COMES ªONº STEADY (Page 1 of 2)
CAUTION:
When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).
When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.
When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
STEPACTIONYESNO
11) Ignition switch OFF.
2) Remove and inspect ªAIR BAGº fuse.
3) Is fuse good?Go to step 2.ªBI/Rº wire short to ground.
After repair, replace
ªAIR BAGº fuse.
21) Disconnect SDM.
2) Check proper connection to SDM at
terminal ªA16º.
3) If OK then check voltage between ªA16º
terminal of SDM connector and body
ground with ignition switch ON.
4) Is it 8 V or more?Go to step 3.ªBI/Rº wire (between
ªAIR BAGº fuse and SDM
connector) open ªBI/Bº wire
(between ignition switch and
ªAIR BAGº fuse) open or short
to ground.
31) Disconnect 16p connector from
combination meter, referring to Section
8C.
2) Check resistance between ªA5º terminal
of SDM connector and body ground.
3) Is resistance 1 k or more?Substitute a known-
good SDM and
recheck.ªBIº wire (between combina-
tion meter and SDM connec-
tor) short to ground.
Page 724 of 801
YH4
GRAND
VITARA
7. SDM
7-1. ªAIR BAGº warning lamp driver circuit 4. ªAIR BAGº warning lamp in combination meter
5. ªAIR BAGº fuse in ªAIR BAGº fuse box
6. Connection detection pin 1. From main fuse
2. Ignition switch
3. ªIG
.COIL METERº fuse in J/B: Air bag harness
10B-18 AIR BAG SYSTEM
TABLE B ± ªAIR BAGº WARNING LAMP DOES NOT COME ªONº (Page 1 of 2)
CAUTION:
When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).
When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.
When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
STEPACTIONYESNO
11) Set parking brake.
2) Note combination meter as ignition switch
is turned ON.
3) Does the ªBRAKEº indicator (warning lamp)
come ON?Go to step 2.ªB/Wº wire, ªIG.COIL
METERº fuse or J/B
(between ignition
switch and combination
meter) open or short to
ground.
21) With ignition switch OFF, disconnect SDM.
2) Check electrical connection check
mechanism (connection detection pin).
3) Is it in good condition?Go to step 3.Repair electrical
connection check
mechanism.
31) Disconnect SDM.
2) Check proper connection to SDM at
terminal ªA5º.
3) If OK then check voltage from ªA5º terminal of
SDM connector to body ground with ignition
switch ON.
4) Is it 9 V or more?Substitute a known-good
SDM and recheck.Go to step 4 on the
next page.
Page 725 of 801
YH4
GRAND
VITARA
(A)ªA5º
1. Combination meter connector (16p)
2. ªY / Gº wire terminal1. Connection detection pin
AIR BAG SYSTEM 10B-19
TABLE B ± ªAIR BAGº WARNING LAMP DOES NOT COME ªONº (Page 2 of 2)
STEPACTIONYESNO
41) Remove combination meter, referring to
SECTION 8C.
2) Check proper connection to combination
meter at terminal for ªAIR BAGº warning lamp
and to SDM at terminal ªA5º.
3) If OK then check resistance between ªY / Gº
wire terminal of combination meter connector
(16p) and ªA5º terminal of SDM connector.
4) Is resistance 1 or less?Go to step 5.Repair high resistance
or open in ªBIº or ªY / Gº
wire circuit (between
combination meter and
SDM).
51) Measure voltage from ªA5º terminal of SDM
connector to body ground with ignition switch
ON.
2) Is it 9 V or more?Repair short from ªBIº or
ªY / Gº wire circuit
(between combination
meter and SDM) to
power circuit.Go to step 6.
61) Remove and inspect ªAIR BAGº bulb.
2) Is bulb good?Substitute a known-good
combination meter and
recheck.Replace bulb.
Fig. for STEP 2 Fig. for STEP 3 and 5
Fig. for STEP 4
Special Tool
(A): 09932-76010
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11 to confirm that the trouble
has been corrected.
Page 726 of 801
YH4
GRAND
VITARA
1. From main fuse
2. Ignition switch
3. ªIG
.COIL METERº fuse in J/B
4. ªAIR BAGº warning lamp in combination meter7. Connection detection pin
8. SDM
8-1. ªAIR BAGº warning lamp driver circuit -5. ªAIR BAGº fuse in ªAIR BAGº fuse box
-6. ªAIR BAGº monitor coupler
6-1. Diagnosis switch terminal : Air bag harness
6±1 6
10B-20 AIR BAG SYSTEM
TABLE C ± ªAIR BAGº WARNING LAMP FLASHES (Page 1 of 2)
CAUTION:
When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).
When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.
When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
STEPACTIONYESNO
11) Check ªAIR BAGº monitor coupler.
2) Is it connected diagnosis switch terminal and
ground terminal in ªAIR BAGº monitor coupler
by service wire?Remove service wire.Go to step 2.
21) With ignition switch OFF, disconnect SDM.
2) Measure resistance between ªA8º terminal of
SDM connector and body ground.
3) Is resistance 1 k or more?Substitute a known-good
SDM and recheck.Repair short from ªVº
wire circuit to ground.
Page 728 of 801
YH4
GRAND
VITARA
1. From main fuse
2. Ignition switch
3. ªIG
.COIL METERº fuse in J/B
4. ªAIR BAGº warning lamp in combination lamp
5. ªAIR BAGº fuse in ªAIR BAGº fuse box6. DLC
7. To, ICM (if equipped)
8. Connection detection pin
9. SDM
9-1. ªAIR BAGº warning lamp driver circuit : Air bag harness
10B-22 AIR BAG SYSTEM
TABLE D ± SDM CANNOT COMMUNICATE THROUGH THE SERIAL DATA CIRCUIT
(Page 1 of 2)
CAUTION:
When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).
When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.
When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
STEPACTIONYESNO
11) Make sure that scan tool (Tech 1) is free
from malfunction and correct cartridge for
air bag system is used.
2) Ignition switch OFF.
3) Check proper connection of scan tool
(Tech 1) to DLC.
4) Is connection in good condition?Go to step 2 on
next page.Properly connect scan
tool to DLC.