2004 SUZUKI GRAND VITARA Ignition switch

YH4
GRAND
VITARA
IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED) 8G-29
7) If any other Transponder code for ignition key with a built-in
transponder needs to be registered, repeat above Steps 3), 5)
and 6).
NOTE:

Up to 4 Transponder codes for ignition key with a built-in
transponder can be registered.

It is not possible to register the same Transponder code
for ignition key with a built-in transponder as the one al-
ready registered in Immobilizer Control Module.
PROCEDURE AFTER IMMOBILIZER
CONTROL MODULE REPLACEMENT
When Immobilizer Control Module was replaced, including when
replaced because rechecking by using a known-good Immobilizer
Control Module was necessary during trouble diagnosis, register
Transponder code and ECM / Immobilizer Control Module code in
Immobilizer Control Module and ECM / Immobilizer Control Module
code in ECM/PCM by performing following procedure.
1) Perform Steps 1) and 2) described in ªHow to register ignition
keyº section.
2) Prepare ignition key with a built-in transponder. And then turn
ignition switch ON by using it.
3) Using Suzuki scan tool, clear all transponder codes registered
in Immobilizer Control Module by executing ªCLR. TRANS COD
(CLEAR TP CODE)º command in SELECT MODE menu.
NOTE:
When ªCLR. TRANS COD (CLEAR TP CODE)º command is
executed with the malfunction indicator lamp (the lamp for
vehicles equipped with the monitor coupler) ON or the im-
mobilizer indicator lamp (the lamp for vehicles not
equipped with the monitor coupler) ON, it remains ON even
after execution of that command is over. It will start flashing
when the ignition switch is turned OFF once and then
turned ON after some seconds.
4) Using Suzuki scan tool, register Transponder code in Immobiliz-
er Control Module by executing ªENT. TRANS COD (ENT. TP
CODE)º command in SELECT MODE menu.
5) Using Suzuki scan tool, register ECM / Immobilizer Control Mod-
ule code in both Immobilizer Control Module and ECM / PCM by
executing ªRECORD ECU (RECORD ECM / PCM / ICM)º com-
mand in SELECT MODE menu.
6) [Vehicle equipped with monitor coupler]
Make sure that malfunction indicator lamp lights when ignition
switch is turned OFF once and then ON.
[Vehicle not equipped with monitor coupler]
Make sure that immobilizer indicator lamp lights when ignition
switch is turned OFF once and then ON.
7) If any other Transponder code for ignition key with a built-in trans-
ponder needs to be registered, repeat above Steps 2), 4) and 6).
NOTE:

Up to 4 Transponder codes for ignition key with a built-in
transponder can be registered.

It is not possible to register the same Transponder code
for ignition key with a built-in transponder as the one al-
ready registered in Immobilizer Control Module.

YH4
GRAND
VITARA
8G-30 IMMOBILIZER CONTROL SYSTEM (IF EQUIPPED)
09931-76030
16 / 14 pin DLC cable
09931-76011
Suzuki scan tool (Tech 1A kit)1. Storage case
2. Operator's manual
3. Tech 1A
4. DLC cable
(14 / 26 pin, 09931-76040)
5. Test lead/probe
6. Power source cable
7. DLC cable adapter
8. Self-test adapter
Immobilizer cartridge of
version 1.1 or more
NOTE:
Use this cable only with im-
mobilizer cartridge of ver-
sion 1.1 or more.
Use of this cable with 96
immobilizer cartridge will
disable 96 immobilizer car-
tridge from operating prop-
erly.
Mass storage cartridge of
version1.5 or more
PROCEDURE AFTER ECM / PCM
REPLACEMENT
When ECM / PCM was replaced, including when replaced because
rechecking by using a known-good ECM / PCM was necessary dur-
ing trouble diagnosis, register ECM/Immobilizer Control Module
code in ECM / PCM by performing following procedure.
1) Perform Steps 1) and 2) described in ªHow to register ignition
keyº section. And then turn ignition switch ON.
2) Using TECH1, register ECM/Immobilizer Control Module code in
ECM / PCM by executing ªRECORD ECU (RECORD ECM / PCM/
ICM)º command in SELECT MODE menu.
NOTE:
For operation procedure of Suzuki scan tool, refer to TECH1
operator's manual.
3) [Vehicle equipped with monitor coupler]
Make sure that malfunction indicator lamp lights when ignition
switch is turned OFF once and then ON.
[Vehicle not equipped with monitor coupler]
Make sure that immobilizer indicator lamp lights when ignition
switch is turned OFF once and then ON.
SPECIAL TOOLS

YH4
GRAND
VITARA
9
BODY SERVICE 9-1
GLASS, WINDOWS AND MIRRORS9- 2 . . . . .
Front Door Glass 9- 2. . . . . . . . . . . . . . . . . . . . .
Front Door Window Regulator 9- 5. . . . . . . . . .
Windshield 9- 6. . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Door Glass 9-12. . . . . . . . . . . . . . . . . . . . .
Rear Door Window Regulator 9-14. . . . . . . . . .
Quarter Window 9-15. . . . . . . . . . . . . . . . . . . . . .
Back Door Glass 9-16. . . . . . . . . . . . . . . . . . . . .
BODY STRUCTURE9-17 . . . . . . . . . . . . . . . . . . .
Front Door Assembly 9-17. . . . . . . . . . . . . . . . .
Rear Door Assembly 9-18. . . . . . . . . . . . . . . . . .
Back Door / Rear Gate Assembly 9-19. . . . . . . .
Hood 9-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Fender 9-22. . . . . . . . . . . . . . . . . . . . . . . . .
Front Bumper 9-23. . . . . . . . . . . . . . . . . . . . . . . .
Rear Bumper 9-24. . . . . . . . . . . . . . . . . . . . . . . .
Under Body Dimensions 9-25. . . . . . . . . . . . . . .
Body Dimensions 9-26. . . . . . . . . . . . . . . . . . . . .
INSTRUMENTATION AND DRIVER
INFORMATION9-33 . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel 9-33. . . . . . . . . . . . . . . . . . . . .
SEAT9-34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Seat 9-34. . . . . . . . . . . . . . . . . . . . . . . . . . . Rear Seat 9-35. . . . . . . . . . . . . . . . . . . . . . . . . . .
PAINT AND COATINGS9-36 . . . . . . . . . . . . . . . .
Anti-Corrosion Treatment 9-36. . . . . . . . . . . . . .
Metal Replacement Parts Finishing 9-37. . . . .
Plastic Parts Finishing 9-58. . . . . . . . . . . . . . . . .
SECURITY AND LOCKS9-59 . . . . . . . . . . . . . . . .
Front Door Lock Assembly 9-59. . . . . . . . . . . . .
Rear Door Lock Assembly 9-61. . . . . . . . . . . . .
Back Door / Rear Gate Lock Assembly 9-62. . .
Key Coding 9-63. . . . . . . . . . . . . . . . . . . . . . . . . .
SUNROOF / CONVERTIBLE TOP9-64 . . . . . . . . .
Sliding Roof (if equipped) 9-64. . . . . . . . . . . . . .
Canvas Top And Topbow Frames 9-71. . . . . . .
EXTERIOR AND INTERIOR TRIM9-72 . . . . . . .
Floor Carpet 9-72. . . . . . . . . . . . . . . . . . . . . . . . .
Head lining 9-73. . . . . . . . . . . . . . . . . . . . . . . . . .
Roof Trim (2 Door Model) 9-75. . . . . . . . . . . . . .
Side Moldings (if equipped) 9-77. . . . . . . . . . . .
Splash Guard (if equipped) 9-78. . . . . . . . . . . .
Roof Rail (if equipped) 9-79. . . . . . . . . . . . . . . .
Roof Molding 9-79. . . . . . . . . . . . . . . . . . . . . . . .
Luggage Under Box 9-80. . . . . . . . . . . . . . . . . .
SECTION 9
BODY SERVICE
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).

When body servicing, if shock may be applied to air bag system component parts, remove those parts
beforehand. (Refer to Section 10B.)
NOTE:
Fasteners are important attaching parts in that they could affect the performance of vital components and
systems, and / or could result in major repair expense. They must be replaced with one of the same part
number of with an equivalent part if replacement becomes necessary.
Do not use a replacement part of lesser quality or substitute a design. Torque values must be used as spe-
cified during reassembly to assure proper retention of these parts.
CONTENTS

YH4
GRAND
VITARA
BODY SERVICE 9-63
KEY CODING
KEY USAGE AND IDENTIFICATION
Key is used for ignition and door lock cylinder. Keys are cut on both
edges to make them reversible.
Key identification is obtained from five character key code stamped
on key code tag. Using this key code, key code cutting combination
can be determined from a code list (available to owners of key cut-
ting equipment from suppliers).
If key codes are not available from records or tags, key code can
be obtained from the right hand door lock cylinder (if lock has not
been replaced). Lock cylinders supplied by the factory as service
parts are unmarked.
If original key is available, key code cutting combination can be de-
termined by laying key.
IGNITION SWITCH LOCK CYLINDER
Removal / Installation
See Section 3C1, ªAIR BAG STEERING WHEEL AND COLUMNº.
ELECTRICAL DIAGNOSIS
For ignition switch electrical troubleshooting, see Section 8, ªBODY
ELECTRICAL SYSTEMº.

YH4
GRAND
VITARA
10
RESTRAINT SYSTEM 10-1
SECTION 10
RESTRAINT SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
SEAT BELTSECTION 10A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR BAG SYSTEMSECTION 10B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS
GENERAL DESCRIPTION10-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSISRefer to ªDiagnosisº in SECTION 10A and 10B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
10A
SEAT BELT 10A-1
SECTION 10A
SEAT BELT
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CAUTION:
When fasteners are removed, always reinstall them at the same location from which they were re-
moved. If a fastener needs to be replaced, use the correct part number fastener for that application. If
the correct part number fastener is not available, a fastener of equal size and strength (or stronger) may
be used. Fasteners that are not reused, and those requiring thread-locking compound, will be called
out. The correct torque value must be used when installing fasteners that require it. If the above proce-
dures are not followed, parts or system damage could result.
CONTENTS
GENERAL DESCRIPTIONRefer to SECTION 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE10A-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service precautions10A-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front seat belt10A-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear seat belt10A-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS10A-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
WIRE HARNESS COLOR
B : Black
B/W : Black/White
Bl : Blue
Bl/B : Blue/Black
Bl/R : Blue/Red
Br : BrownG : Green
Gr : Gray
G/R : Green/Red
Lg : Lightgreen
P : Pink
V : VioletY : Yellow
Y / G : Yellow/Green
Y/R : Yellow/Red
W : White
W/B : White/Black
1. From main fuse
2. Ignition switch
3. ªIG
.COIL METERº fuse in J/B
4. ªAIR BAGº warning lamp in combination meter
5. ªAIR BAGº fuse in ªAIR BAGº fuse box
6. Connection detection pin
7. To ECM (or PCM), ICM (if equipped) and ABS
controller (if equipped)
8. To data link connector (DLC)
9. ªAIR BAGº monitor coupler
10. SDM
11. Contact coil assembly
12. Driver air bag (inflator) module
13. Driver seat belt pretensioner (if equipped)
14. Passenger air bag (inflator) module
15. Passenger seat belt pretensioner (if equipped)
16. Pretensioner harness (if equipped)
17. Ground for air bag system
TERMINAL
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A13 A11
A12
A14
A15
A16
Passenger air bag (inflator) moduleLow
High
CIRCUIT
Data link connector (DLC)
Low
High
Low
High
Low
High ªAIR BAGº warning lamp
Driver air bag (inflator) module
Diagnosis switch
±±±±±±±±±
Ground
Passenger pretensioner
Driver pretensioner
Ignition switch (power source)±±±±±±±±±
±±±±±±±±±
CONNECTOR ªAº (SDM connector) TERMINAL ARRANGEMENT OF SDM
(VIEWED FROM HARNESS SIDE)
L1
L2Connection detection pin
: Shorting bar
: Air bag harness
ªAº
ªHº : Connector
AIR BAG SYSTEM 10B-5
SYSTEM WIRING DIAGRAM

YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-11
AIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLE
STEPACTIONYESNO
11) Make sure that battery voltage is about
11V or higher.
2) Note ªAIR BAGº warning lamp as ignition
switch is tuned ON.
3) Does ªAIR BAGº warning lamp flash
6 times when ignition switch is tuned ON?Go to step 2.ªAIR BAGº warning lamp
does not come ªONº
Proceed to ªTable Bº
on p.10B-18.
2Does ªAIR BAGº warning lamp keep flashing
(indicating DTC) when ignition switch is
turned ON ?ªAIR BAGº warning
lamp flashes
Proceed to ªTable Cº
on p.10B-20.Go to step 3.
3After flashing 6 times then does
ªAIR BAGº warning lamp turn OFF?Go to step 4.Go to step 5.
41) Check DTC, referring to ªDiagnostic
Trouble Code (DTC) Checkº on
p.10B-12.
2) [Using SUZUKI scan tool]
Is ªNO CODESº displayed ?
NOTE:
If SDM cannot communicate through
serial data circuit, proceed to ªTable
Dº on p.10B-22.
[Not using SUZUKI scan tool]
Is DTC 12 indicated ?Air bag system is in
good condition.NOTE:
As execution of the ªDiag-
nostic Trouble Code (DTC)
Clearanceº will clear all
DTCs, be sure to record all
DTCs before servicing.
An intermittent trouble has
occurred at some place.
Check the connector
harness, etc. related to the
sensed DTC (Refer to
ªIntermittent and Poor
Connectionsº in this section.).
Then clear DTC (Refer to
p.10B-13.) and repeat this
table.
51) Check DTC, referring to ªDiagnostic
Trouble Code (DTC) Checkº on
p.10B-12.
2) [Using SUZUKI scan tool]
Is ªNO CODESº displayed ?
NOTE:
If SDM cannot communicate through
serial data circuit, proceed to ªTable
Dº on p.10B-22.
[Not using SUZUKI scan tool]
Is DTC 12 indicated ?ªAIR BAGº warning
lamp come ªONº
steady
Proceed to ªTable Aº on
p.10B-16.NOTE:
As execution of the ªDiag-
nostic Trouble Code (DTC)
Clearanceº will clear all
DTCs, be sure to record all
DTCs before servicing.
Check and repair according
to Flow Table corresponding
to that DTC.