Page 715 of 801
YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-9
Wire insulation which is rubbed through, causing an intermittent
short as the bare area touches other wiring or parts of the vehicle.
Wiring broken inside the insulation. This condition could cause a
continuity check to show a good circuit, but if only 1 or 2 strands
of a multi-strand-type wire are intact, resistance could be far too
high.
If any abnormality is found, repair or replace as a wire harness as-
sembly.
Page 717 of 801
YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-11
AIR BAG DIAGNOSTIC SYSTEM CHECK FLOW TABLE
STEPACTIONYESNO
11) Make sure that battery voltage is about
11V or higher.
2) Note ªAIR BAGº warning lamp as ignition
switch is tuned ON.
3) Does ªAIR BAGº warning lamp flash
6 times when ignition switch is tuned ON?Go to step 2.ªAIR BAGº warning lamp
does not come ªONº
Proceed to ªTable Bº
on p.10B-18.
2Does ªAIR BAGº warning lamp keep flashing
(indicating DTC) when ignition switch is
turned ON ?ªAIR BAGº warning
lamp flashes
Proceed to ªTable Cº
on p.10B-20.Go to step 3.
3After flashing 6 times then does
ªAIR BAGº warning lamp turn OFF?Go to step 4.Go to step 5.
41) Check DTC, referring to ªDiagnostic
Trouble Code (DTC) Checkº on
p.10B-12.
2) [Using SUZUKI scan tool]
Is ªNO CODESº displayed ?
NOTE:
If SDM cannot communicate through
serial data circuit, proceed to ªTable
Dº on p.10B-22.
[Not using SUZUKI scan tool]
Is DTC 12 indicated ?Air bag system is in
good condition.NOTE:
As execution of the ªDiag-
nostic Trouble Code (DTC)
Clearanceº will clear all
DTCs, be sure to record all
DTCs before servicing.
An intermittent trouble has
occurred at some place.
Check the connector
harness, etc. related to the
sensed DTC (Refer to
ªIntermittent and Poor
Connectionsº in this section.).
Then clear DTC (Refer to
p.10B-13.) and repeat this
table.
51) Check DTC, referring to ªDiagnostic
Trouble Code (DTC) Checkº on
p.10B-12.
2) [Using SUZUKI scan tool]
Is ªNO CODESº displayed ?
NOTE:
If SDM cannot communicate through
serial data circuit, proceed to ªTable
Dº on p.10B-22.
[Not using SUZUKI scan tool]
Is DTC 12 indicated ?ªAIR BAGº warning
lamp come ªONº
steady
Proceed to ªTable Aº on
p.10B-16.NOTE:
As execution of the ªDiag-
nostic Trouble Code (DTC)
Clearanceº will clear all
DTCs, be sure to record all
DTCs before servicing.
Check and repair according
to Flow Table corresponding
to that DTC.
Page 721 of 801
YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-15
DIAGNOSTIC TROUBLE CODE TABLE (Page 2 of 2)
DIAGNOSTIC TROUBLE CODEDIAGNOSISNO.MODEDIAGNOSIS
41Resistance high
42Driver
pretensionerResistance low
43circuit
(if equipped)Short to ground
44Short to power circuit
45Resistance highDiagnose trouble
di t ªDi
46Passenger
pretensionerResistance low
according to ªDiagnos-
tic Flow Tableº corre-
sponding to each code
47circuit
(if equipped)Short to ground
s onding to each code
No.
48Short to power circuit
51SDMFrontal crash detected
61ªAIR BAGº warning lamp circuit
71SDMInternal fault
NOTE:
When 2 or more codes are indicated, the lowest numbered code will appear first.
If a code not listed on the table is displayed, then the SDM is faulty.
Current DTC and history DTC can be identified by lighting and flashing of ªAIR BAGº warning lamp as
follows.
Current DTC is set.
(Abnormality exists at present.)History DTC is set only. (Faulty condi-
tion occurred once in the past but nor-
mal condition is restored at present.)
ªAIR BAGº warning lamp
after ignition switch ONRemains ON.Flashing 6 times and turns OFF.
ªAIR BAGº warning lamp
when grounding diagnosis
switch
Current DTC is displayed.History DTC is displayed.
However, if a multiple number of DTC's are set an even one of them is a current DTC, ªAIR BAGº warning
lamp remains on after ignition switch is turned ON. Therefore, it is not possible to identify any of them
as to whether it is a current one or a history one. (But use of scan tool (Tech 1) will make identification
possible.)
Page 724 of 801
YH4
GRAND
VITARA
7. SDM
7-1. ªAIR BAGº warning lamp driver circuit 4. ªAIR BAGº warning lamp in combination meter
5. ªAIR BAGº fuse in ªAIR BAGº fuse box
6. Connection detection pin 1. From main fuse
2. Ignition switch
3. ªIG
.COIL METERº fuse in J/B: Air bag harness
10B-18 AIR BAG SYSTEM
TABLE B ± ªAIR BAGº WARNING LAMP DOES NOT COME ªONº (Page 1 of 2)
CAUTION:
When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).
When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.
When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
STEPACTIONYESNO
11) Set parking brake.
2) Note combination meter as ignition switch
is turned ON.
3) Does the ªBRAKEº indicator (warning lamp)
come ON?Go to step 2.ªB/Wº wire, ªIG.COIL
METERº fuse or J/B
(between ignition
switch and combination
meter) open or short to
ground.
21) With ignition switch OFF, disconnect SDM.
2) Check electrical connection check
mechanism (connection detection pin).
3) Is it in good condition?Go to step 3.Repair electrical
connection check
mechanism.
31) Disconnect SDM.
2) Check proper connection to SDM at
terminal ªA5º.
3) If OK then check voltage from ªA5º terminal of
SDM connector to body ground with ignition
switch ON.
4) Is it 9 V or more?Substitute a known-good
SDM and recheck.Go to step 4 on the
next page.
Page 728 of 801
YH4
GRAND
VITARA
1. From main fuse
2. Ignition switch
3. ªIG
.COIL METERº fuse in J/B
4. ªAIR BAGº warning lamp in combination lamp
5. ªAIR BAGº fuse in ªAIR BAGº fuse box6. DLC
7. To, ICM (if equipped)
8. Connection detection pin
9. SDM
9-1. ªAIR BAGº warning lamp driver circuit : Air bag harness
10B-22 AIR BAG SYSTEM
TABLE D ± SDM CANNOT COMMUNICATE THROUGH THE SERIAL DATA CIRCUIT
(Page 1 of 2)
CAUTION:
When measurements are requested in this chart use specified digital multimeter with correct terminal
adapter from special tool (Connector test adapter kit).
When a check for proper connection is requested refer to ªIntermittent and Poor Connectionsº in this
section.
When an open in air bag wire harness, damaged wire harness, connector or terminal is found, replace
wire harness, connectors and terminals as an assembly.
STEPACTIONYESNO
11) Make sure that scan tool (Tech 1) is free
from malfunction and correct cartridge for
air bag system is used.
2) Ignition switch OFF.
3) Check proper connection of scan tool
(Tech 1) to DLC.
4) Is connection in good condition?Go to step 2 on
next page.Properly connect scan
tool to DLC.
Page 760 of 801
YH4
GRAND
VITARA
10B-54 AIR BAG SYSTEM
CODE 61 ± ªAIR BAGº WARNING LAMP CIRCUIT FAILURE (Page 2 of 2)
NOTE:
Before executing items in this table, be sure to perform ªAir Bag Diagnostic System Check Flow Tableº.
STEP
ACTIONYESNO
11) This DTC is set when there is a trouble in
ªAIR BAGº warning lamp circuit. Failure to
properly perform ªAir Bag Diagnostic System
Check Flow Tableº may also result in
misdiagnosis. Therefore, check ªAIR BAGº
warning lamp circuit again according to ªAir
Bag Diagnostic System Check Flow Tableº.
2) Is ªAIR BAGº warning lamp circuit in good
condition?Go to step 2.Repair ªAIR BAGº
warning lamp circuit.
21) Clear diagnostic trouble codes.
2) Is DTC 61 set ?Substitute a known-
good SDM and recheck.Recheck air bag system,
referring to ªAir Bag
Diagnostic System
Check Flow Tableº.
NOTE:
Upon completion of inspection and repair work, perform following items.
1) Reconnect all air bag system components, ensure all components are properly mounted.
2) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p. 10B-11 to confirm that the trouble
has been corrected.
CODE 71 ± INTERNAL SDM FAULT
DTC WILL SET WHEN:
An internal SDM fault is detected by SDM.
NOTE:
CODE 71 can never be cleared once it has been set.
1) Ignition switch OFF.
2) Replace SDM.
3) Repeat ªAir Bag Diagnostic System Check Flow Tableº, referring to p.10B-11.
Page 763 of 801
YH4
GRAND
VITARA
1. Yellow connector of passenger air bag (inflator) module
2. Steering support member
3. Air bag harness
AIR BAG SYSTEM 10B-57
3) Connect Yellow connector of passenger air bag (inflator) mod-
ule, and be sure to lock connector with lock lever.
ii) Connect connector.
ii) Lock connector with lock lever.
4) Install glove box.
5) Install ªAIR BAGº fuse to ªAIR BAGº fuse box.
6) Turn ignition switch to ON and verify that ªAIR BAGº warning
lamp flashes 6 times and then turns off.
If it does not operate as described, perform ªAir Bag Diagnostic
System Checkº in this section.
HANDLING AND STORAGE
SDM
WARNING:
Never power up air bag system when SDM is not rigidly at-
tached to the vehicle. Otherwise, personal injury may result.
CAUTION:
After detecting one time of such collision as to meet deploy-
ment conditions, the SDM must not be used.
Refer to ªDiagnosisº when checking the SDM.
Never attempt disassembly of SDM.
When storing SDM, select a place where neither high tempera-
ture nor high humidity is anticipated and oil, water and dust are
kept off.
If SDM was dropped from a height of 90 cm (3 ft) or more or if it
is found to be damaged or deformed, replace it with a new one.
If installation part of SDM was damaged, repair that part com-
pletely before reinstallation.
All SDM and mounting bracket fasteners must be carefully
torqued and the arrow must be pointed toward the front of the ve-
hicle to ensure proper operation of the air bag system.
Page 769 of 801
YH4
GRAND
VITARA
AIR BAG SYSTEM 10B-63
REPAIRS AND INSPECTIONS REQUIRED AFTER AN ACCIDENT
CAUTION:
All air bag system components, including the electrical harness (component mounting points), must
be inspected after an accident. If any components are damaged or bent, they must be replaced even
if air bag system activation did not occur.
Never use air bag system parts from another vehicle.
Do not attempt to service the parts below. Service of these parts is by replacement only.
± Driver/Passenger air bag (inflator) module
± Driver/Passenger seat belt pretensioner
± SDM
± Contact coil and combination switch assembly
± Air bag wire harness
Proper operation of the sensors and air bag system requires that any repairs to the vehicle structure
return it to its original production configuration.
CAUTION:
After detecting one time of such collision as to meet deployment conditions, the SDM must not be used.
Refer to ªDiagnosisº when checking the SDM.
ACCIDENT WITH DEPLOYMENT ± COMPONENT
REPLACEMENT
Certain air bag system components must be replaced. Those com-
ponents are:
Driver and passenger air bag (inflator) modules
± Replace with new one.
Driver and passenger seat belt pretensioners
± Replace with new one as an assembly.
SDM after detecting such collision as to meet deployment condi-
tions
± Replace with new one.
