2004 SUZUKI GRAND VITARA Air condition

YH4
GRAND
VITARA
7D
TRANSFER 7D-1
The aluminum transfer case directly connected to the
back of the transmission contains the input gear,
countershaft & gear, output rear shaft, output low gear
and output front shaft (for front drive) connected by
way of the hyvo-chain.
The transfer has such a selective mechanism as to
enable the shift control lever to make selection of high
speed (direct connection with transmission output:
main shaft), low speed (speed reduction by input
gear, counter gear and output low gear) or neutral by
way of the reduction sleeve located between input
gear and output low gear, and selection of two-wheel-
drive (high speed only) or four-wheel-drive (high or
low speed) by way of the front drive clutch sleeve lo-cated at the center of the output rear shaft. Also, with
a synchronizer installed to the front drive clutch, it is
possible to change the drive mode between 2WD
(high speed only) and 4WD (high speed only) even
while running.
The front drive shift fork has an auxiliary spring to
make a smooth shift from 4H to 2H possible.
The case has an oil gutter and a plate at synchronizer
to provide proper lubrication even under the strict
conditions of use.
WARNING:
For towing the vehicle for the purpose of repair or
the like, follow the towing instructions in OWN-
ER'S MANUAL.
SECTION 7D
TRANSFER
CONTENTS
GENERAL DESCRIPTION7D-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS7D-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table7D-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gear Oil7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Oil Seals7D-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer Driven Gear7D-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Rear Mounting7D-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transfer Assembly7D-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dismounting7D-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remounting7D-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIT REPAIR7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL7D-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL DESCRIPTION

YH4
GRAND
VITARA
7D-2 TRANSFER
DIAGNOSIS
DIAGNOSIS TABLE
Before attempting to repair the transfer or related components for any reason other than mechanical failure, the
condition and probable causes should be identified.
Transfer failures are revealed by shifting difficulties such as excessive shifting effort, gear clash, or gear grinding.
When any of these conditions occur, the following inspections should be made before disassembling the transfer.
1) Check transfer oil level for insufficient or incorrect oil. Refer to ªTransfer and Differential Oil Inspection and
Changeº in SECTION 0B ªMAINTENANCE AND LUBRICATIONº.
2) Check transfer mountings for wear or looseness.
3) Check gearshift control lever for distortion or excessive wear.
After performing the above inspections, refer to following diagnosis table.
Condition
Possible CauseCorrection
Gear slipping out of mesh
Worn shift fork shaft

Worn shift fork or synchronizer sleeve

Weak or damaged locating spring

Worn bearings on output rear shaft

Worn chamfered tooth on sleeve or gear

Missing or disengagement of circlip(s)Replace
Replace
Replace
Replace
Replace sleeve and gear
Install
Gears refusing to disengage
Weakened or broken synchronizer spring

Distorted shift shaft or shift forkReplace
Replace
Hard shifting
Weakened front drive shift shaft spring

Distorted or mispositioned front drive shift
shaft circlip and washer

Inadequate or insufficient lubricant

Worn synchronizer ring

Worn chamfered tooth on sleeve or gear

Distorted shift shaftReplace
Replace
Replenish
Replace
Replace sleeve and gear
Replace
Noise
Inadequate or insufficient lubricant

Damaged or worn bearing(s)

Damaged or worn gear(s)

Damaged or worn synchronizer ring

Damaged or worn chamfered tooth on
sleeve or gearReplenish
Replace
Replace
Replace
Replace

YH4
GRAND
VITARA
DIFFERENTIAL (FRONT) 7E-5
DIAGNOSIS
DIAGNOSIS TABLE
Differential Assembly
ConditionPossible CauseCorrection
Gear noise
Deteriorated or water mixed lubricant

Inadequate or insufficient lubricant

Maladjusted backlash between bevel
pinion and gear

Improper tooth contact in the mesh between
bevel pinion and gear

Loose bevel gear securing bolts

Damaged side gear(s) or side pinion(s)Repair and replenish
Repair and replenish
Adjust
Adjust or replace
Replace or retighten
Replace
Bearing noise
(Constant noise) Deteriorated or water
mixed lubricant

(Constant noise) Inadequate or insufficient
lubricant

(Noise while coasting) Damaged bearing(s)
of bevel pinion

(Noise while turning) Damaged diff. side
bearing(s) or axle bearing(s)Repair and replenish
Repair and replenish
Replace
Replace
Oil leakage
Worn or damaged oil seal

Excessive oil

Loose differential carrier boltsReplace
Adjust oil level
Replace or retighten
2WD / 4WD
switching error
Defective actuator

Abnormality in 4WD control systemReplace
Inspect referring to ª4WD
CONTROL SYSTEM DIAG-
NOSTIC FLOW TABLEº.
4WD Control System Diagnostic Flow Table
Before performing the trouble diagnosis, check that the transfer and front differential are in good condition and
there is no air leakage from air hoses and the actuator. Refer to ªON-VEHICLE SERVICEº in this section for air
leakage.
[NOTES ON SYSTEM CIRCUIT INSPECTION]

Be sure to read ªPrecautions for Electrical Circuit Serviceº in Section 0A before circuit inspection and observe
what is written there.

For system circuit, refer to the figure of ªGENERAL DESCRIPTIONº in this section.

For terminal arrangement, refer to ª4WD Control Circuit Inspectionº in this section.

YH4
GRAND
VITARA
7E-6 DIFFERENTIAL (FRONT)
STEPACTIONYESNO
1Turn ON ignition switch (but engine at stop) and
check malfunction indicator lamp.
Does lamp light up?Go to step 2.A trouble has
occurred at some
place. Repair it
referring to
MALFUNCTION
INDICATOR LAMP
(ªCHECK ENGINEº
LAMP) CHECK in
DIAGNOSIS of
SECTION 6.
2Check 4WD switch circuit.
Turn ignition switch ON and check that voltage
between terminal C51-2-18 and terminal C51-3-17
(ground) for G16 / J20 (terminal C51-1-11 and terminal
C51-3-26 (ground) for H25) is as follows.

When transfer shift lever is in N or 2H: 10 ± 14 V

When transfer shift lever is in 4L or 4H: 0 ± 1 V
Is the check result satisfactory?Go to step 3.Check 4WD switch
(refer to SECTION
7A), ªB / Orº and ªBº
circuits of 4WD
switch.
If OK, substitute a
known-good ECM
(PCM) and recheck.
3Check power supply.
1) Turn ignition switch ON.
2) Check voltage between C51-2-7 and C51-3-17
(ground) for G16 / J20 (C51-1-15 and C51-3-26
(ground) for H25). The check results should be as
follows.

When transfer shift lever is in N or 2H: 0 ± 1 V

When transfer shift lever is in 4L or 4H: 10 ± 14 V
Is the check result satisfactory?Go to step 4.Check ªRº circuit. If
it is OK, substitute a
known-good ECM
(PCM) and recheck.
4Check air pump assembly circuit.
1) Check for proper connection to air pump
assembly at all terminals.
2) Turn ignition switch ON.
3) Check voltage between C51-2-27 and C51-3-17
(ground) for G16 / J20 (C51-1-18 and C51-3-26
(ground) for H25). The check result should be as
follows.

When transfer shift lever is in 2H or N: 0 ± 1 V

When transfer shift lever is in 4L or 4H
(more than 4 seconds after shifted to 4L or 4H):
10 ± 14 V
Is the check result satisfactory?Go to step 5.Check air pump
assembly referring
to ªON-VEHICLE
SERVICEº, and then
ªPº circuit.
If OK, substitute a
known-good ECM
(PCM) and recheck.
5Check 4WD indicator lamp circuit.
1) Turn ignition switch ON.
2) Check voltage between E61-19 and C51-3-17
(ground) for G16 / J20 (C51-1-7 and C51-3-26
(ground) for H25). The check result should be as
follows.

When transfer shift lever is in 2H or N: 10 ± 14 V

When transfer shift lever is in 4L or 4H: 0 ± 1 V
Is the check result satisfactory?4WD control system
is in good condition.Check ªOr / Bº circuit
(including indicator
lamp and
combination meter).
If OK, substitute a
known-good ECM
(PCM) and recheck.

YH4
GRAND
VITARA
DIFFERENTIAL (FRONT) 7E-7
1
1. ECM (PCM); viewed from harness side
4WD CONTROL CIRCUIT INSPECTION
Voltage Check [G16 and J20 engine models]
Check for input or output voltage (voltage between each circuit and
body ground) of ECM (PCM) with ECM (PCM) connector con-
nected and ignition switch turned ON.
TER-
MINALCIRCUITWIRE
COLORNORMAL
VOLTAGECONDITION
E6110 ± 14 VTransfer shift lever: 2H or NE61-
194WD Indicator lampOr / B0 ± 1 V4 seconds after transfer shift lever shifted
to 4H or 4L
C51 2Air pump assembly0 ± 1 VTransfer shift lever: 2H or NC51-2
-7(Pump motor and release
valve)R10 ± 14 V1 seconds after transfer shift lever shifted
to 4H or 4L
C51-24WD switchB/Or10 ± 14 VTransfer shift lever: 2H or N
-184WD switchB/Or0 ± 1 VTransfer shift lever: 4H or 4L
C51-
3-17GroundB/Bl0 ± 1 V±
C51 2Airpumpassembly0 ± 1 VTransfer shift lever: 2H or NC51-2
-27
Air um assembly
(pressure switch)P10 ± 14 V4 seconds after transfer shift lever shifted
to 4H or 4L

YH4
GRAND
VITARA
7E-8 DIFFERENTIAL (FRONT)
1. ECM (PCM); viewed from harness side
Voltage Check [H25 engine model]
TER-
MINALCIRCUITWIRE
COLORNORMAL
VOLTAGECONDITION
C51 110 ± 14 VTransfer shift lever: 2H or NC51-1
-74WD Indicator lampOr / B0 ± 1 V4 seconds after transfer shift lever shifted
to 4H or 4L
C51 1Air pump assembly0 ± 1 VTransfer shift lever: 2H or NC51-1
-15(Pump motor and release
valve)R10 ± 14 V1 seconds after transfer shift lever shifted
to 4H or 4L
C51-14WD switchB/Or10 ± 14 VTransfer shift lever: 2H or N
-114WD switchB/Or0 ± 1 VTransfer shift lever: 4H or 4L
C51-3
-26GroundB/Bl0 ± 1 V±
C51-1Airpumpassembly0 ± 1 VTransfer shift lever: 2H or NC51-1
-18
Air um assembly
(pressure switch)P10 ± 14 V4 seconds after transfer shift lever shifted
to 4H or 4L

YH4
GRAND
VITARA
7F-2 DIFFERENTIAL (REAR)
DIAGNOSIS
ConditionPossible CauseCorrection
Gear noise
Deteriorated or water mixed lubricant

Inadequate or insufficient lubricant

Maladjusted backlash between bevel
pinion and gear

Improper tooth contact in the mesh between
bevel pinion and gear

Loose bevel gear securing bolts

Damaged side gear(s) or side pinion(s)Repair and replenish
Repair and replenish
Adjust as prescribed
Adjust or replace
Replace or retighten
Replace
Bearing noise
(Constant noise) Deteriorated or water
mixed lubricant

(Constant noise) Inadequate or insufficient
lubricant

(Noise while coasting) Damaged bearing(s)
of bevel pinion

(Noise while turning) Damaged diff. side
bearing(s) or axle bearing(s)Repair and replenish
Repair and replenish
Replace
Replace
Oil leakage
Clogged breather plug

Worn or damaged oil seal

Excessive oilClean
Replace
Adjust oil level

YH4
GRAND
VITARA
8
BODY ELECTRICAL SYSTEM 8-1
SECTION 8
BODY ELECTRICAL SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
WIRING SYSTEM
(Harnesses, Connectors, Fuses, Relay, Switches, Grounds, System Circuit Diagram)Section 8A . . . . . . .
LIGHTING SYSTEMSection 8B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUMENTATION AND DRIVER INFORMATIONSection 8C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WINDOWS, MIRRORS, SECURITY AND LOCKSSection 8D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMMOBILIZER CONTROL SYSTEMSection 8F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS
GENERAL DESCRIPTION8-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions in Servicing8-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols and Marks8-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations8-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Color Symbols8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Diagram8-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .