2004 SUBARU OUTBACK power button

2-17
Keys and doors
– CONTINUED –
TTo arm the system using power door locking
switches
1. Close all windows and moonroofs (if so equipped).
2. Remove the key from the ignition switch.
3. Open the doors and get out of the vehicle.
4. Make sure that the engine hood (and the trunk lid)
is locked.
5. Close the doors (and the rear gate on the station
wagon) but leave only the driver’s door or the front
passenger’s door open.
6. Push the power door locking switch forward
(“LOCK” side) to set the door locks.
7. Close the door. An electronic chirp will sound one
time, the turn signal lights will flash one time and the indicator light will start flashing slowly (approximately
once every two seconds) to inform you that the systemhas armed.
NOTE
The system can be armed even if the engine hood,
the windows and/or moonroofs are opened. Al-
ways make sure that they are fully closed before
arming the system. „
Disarming the system
Briefly press the “UNLOCK/DISARM” button (for less
than two seconds) on the remote transmitter. The driv-
er’s door will unlock, an electronic chirp will sound two
times, the turn signal lights will flash two times and the
indicator light will go off.
To unlock all other doors (and the rear gate on the sta-
tion wagon), briefly press the “UNLOCK/DISARM” but-
ton a second time. T Emergency disarming
If you cannot disarm the system using the transmitter
(i.e. the transmitter is lost, broken or the transmitter
battery is too weak), you can disarm the system with-
out using the transmitter. To disarm the system:
6
7
UB2024CC

2-21
Keys and doors
– CONTINUED –
3. Open the doors and get out of the vehicle.
4. Before closing the doors, lock all doors with the in-
side door lock levers.
5. Close the doors. The system will automatically arm
after one minute.
In the passive mode, the system can also be armed
with the remote transmitter or with the power door
locking switches. If the remote transmitter or power
door lock switch is used to lock the vehicle, arming will
take place immediately regardless of whether or not
the passive mode has been selected. TDisarming the system
To disarm the system, briefly press the “UNLOCK/ DISARM” button on the transmitter.T
Tripped sensor identification
If an electronic chirp sounds four times and the turn
signal lights flash four times when you disarm the sys-
tem, this indicates that the alarm was triggered. The
number of times the indicator light flashes indicates
what sensor caused the alarm condition.
To enter identification mode:
1. Open the driver’s door and leave it open.
2. Turn the ignition switch to the “ON” position two times. (“LOCK” “ON” “LOCK” “ON”
“LOCK”)
3. The indicator light will start flashing.
The indicator light provides the following indications.
Flashing one time: Any door, the rear gate or the
trunk lid has been opened.
Flashing three times: The impact sensor in the sys-
tem’s unit has been activated. This may indicate that
your vehicle has been shocked or tampered with by
some outside force and/or unauthorized person.
Flashing four times: The ignition switch has been
turned on or the battery has been disconnected.
NOTE
The battery must be reconnected before the indi-
cator light will flash.
4
35
UB2024DB

5-6
Audio
Type A and B audio set (if equipped)
Type A: Without weather band
Type B: With weather band
The audio set will operate only when the ignition switch is in the “ACC” or
“ON” position. „
Radio operation
(1)
(2)
(3)
(4)
(5)
(6)
UB5052BB
(1) Power switch/Volume, Tone,
Balance, Fader control dial
(2) BAND button
(3) Tuning buttons
(4) Preset buttons
(5) AUDIO button
(6) SCAN button

5-7
Audio
– CONTINUED –
TPower switch and volume/bass/treble/fader/
balance control
V Power switch and volume control (PWR/VOL)
The dial (1) is used for both power (ON/OFF) and vol-
ume control. The radio is turned ON and OFF by push-
ing the dial and the volume is controlled by turning the
dial. V Tone and balance control (AUDIO)
The volume control dial (1) normally functions as a vol-
ume control. This dial becomes a control for Bass,
Treble, Fader or Balance when you select the appro-
priate tone and balance control mode.
Choose desired volume level for each mode by turning
the volume control dial. The control function returns to
volume control mode after about 5 seconds.
To change control modes: Each brief press of the
“AUDIO” button (5) changes control modes in the fol-
lowing sequence starting from volume control mode.
(When the radio is first turned on, the control mode is
in the volume control.) The “AUDIO” button (5) is used for selecting the fol-
lowing control modes:
Volume
(VOL)
Bass(BAS)Treble(TRE)Balance(BAL)
Fader
(FAD)

5-11
Audio
– CONTINUED –
„Compact disc player operation
(7) (8) (9)
(10)
(11)
(12)
(13)
(14) (15)
UB5052CB
(7) Disc slot
(8) CD button
(9) Eject button
(10) Fast forward and track up button
(11) Fast reverse and track down
button
(12) Random button
(13) Repeat button
(14) Scan button
(15) PWR (power) switch

5-17
Audio
– CONTINUED –
Type C audio set (if equipped)
The radio will operate only when the ignition switch is in the “ACC” or “ON” position. „Radio operation
(1) (2) (3) (4) (5)
(6)
(7)
(8)
UB5064BB
(1) Power switch, Volume control,
Bass/Middle/Treble control and
Fader/Balance control dial
(2) AUDIO (audio mode) button
(3) Fader/Balance selection button
(4) FM/AM selection button
(5) WB (weather band) button
(6) Preset buttons
(7) Tuning buttons
(8) SCAN button

5-18
Audio
T
Power switch and volume/bass/treble/fader/
balance control (PWR/VOL)
The dial (1) is used for both power (ON/OFF) and vol-
ume control. The radio is turned ON and OFF by push-
ing the dial and the volume is controlled by turning the
dial.
This dial is used for bass/middle/treble controls when
the “AUDIO” button (2) is in the depressed position. It
is also used for fader/balance controls when the “BAL”
button (3) is in the depressed position.

5-28
Audio „
Radio operation
(1) (2) (3)
(4)
(5)
(6)
(7)
(8)
UB5063BB
(1) FM/AM selection button
(2) Weather band button
(3) Tuning/FF·FB dial
(4) SCAN button
(5) Preset buttons
(6) Fader/Balance control button
(7) Power switch, Volume control,
Bass/Treble control and Fader/
Balance control dial
(8) Bass/Treble sound control but-
ton