2004 NISSAN PATHFINDER width

the Tire and Loading Information label.
5. Add air to the tire as needed. If too much air
is added, press the core of the valve stem
briefly with the tip of the gauge stem to
release pressure. Recheck the pressure and
add or release air as needed.
6. Install the valve stem cap.
7. Check the pressure of all other tires, includ-
ing the spare. (Refer to the “Wheels and
tires” section.)
TIRE LABELINGFederal law requires tire manufacturers to place
standardized information on the sidewall of all
tires. This information identifies and describes
the fundamental characteristics of the tire and
also provides the tire identification number (TIN)
for safety standard certification. The TIN can be
used to identify the tire in case of a recall in case
of recall.
1Tire size (example: P215/60R16 94H)
1 P: The “P” indicates the tire is designed for
passenger vehicles.
2. Three-digit number (215): This number gives
the width in millimeters of the tire from side-
wall edge to sidewall edge.
(Not all tires have this information.)
3. Two-digit number (60): This number, known
as the aspect ratio, gives the tire’s ratio of
height to width.
4. R: The “R” stands for radial.
5. Two-digit number (16): This number is the
wheel or rim diameter in inches.
SDI1575
SDI1606
8-34
Maintenance and do-it-yourself


04.3.9/R50-D/V5


ENGINE
ModelVQ35DE
TypeGasoline, 4-cycle
Cylinder arrangement6-cylinder, V-slanted at 60°
Bore×Stroke in (mm) 3.760×3.205 (95.5×81.4)
Displacement cu in (cm
3) 213.45 (3,498)
Firing order1-2-3-4-5-6
Idle speed rpm
See the “Emission control label” on the underside of the hood. Ignition timing (BTDC) degree/rpm
CO percentage at idle speed [No air] %
Spark plugPL FR5A-11 (Standard)
PL FR4A-11 (Service option)
PL FR6A-11 (Service option)
Spark plug gap in (mm) 0.043 (1.1)
Camshaft operationTiming chain
Alternator belt size
Width×Length in (mm) 0.8409×46.26 (21.36×1,175)
*1: Periodic maintenance is necessary. See “Periodic maintenance” in the “Service and Maintenance Guide” for maintenance intervals.
SPECIFICATIONS
Technical and consumer information
9-9


04.3.9/R50-D/V5


Grade Road wheel &
offset in (mm)Tire size & pressure (cold) Spare tire size &
pressure (cold)
XE 16x7JJ Aluminum/
1.97 (50)P245/70R16 106S
30 psi (210 kPa)P245/70R16 106S
30 psi (210 kPa)
P215/80R16 103M*2
30 psi (210 kPa)
SE
WIDE16x7JJ Aluminum/
0.79 (20)*1P255/65R16 106S*1
30 psi (210 kPa)P255/65R16 106S*1
30 psi (210 kPa)
P215/80R16 103M*2
30 psi (210 kPa)
LE
WIDE17x8JJ Aluminum/
0.79 (20)P245/65R17 105S
30 psi (210 kPa)P245/65R17 105S
30 psi (210 kPa)
P215/80R16 103M*2
30 psi (210 kPa)
*1: Option for XE
*2: If so equipped (for US)
DIMENSIONS AND WEIGHTSPATHFINDER
Overall length*1 in (mm) 182.7 (4,640)
Overall width in (mm) 69.7 (1,770)
71.7 (1,820)*2
Overall height in (mm) 68.1 (1,730)
67.9 (1,725)*2
Front tread in (mm) 58.3 (1,480)
60.6 (1,540)*2
Rear tread in (mm) 58.5 (1,485)
60.8 (1,545)*2
Wheelbase in (mm) 106.3 (2,700)
Gross vehicle weight rating lb(kg) See the “F.M.V.S.S. certification
label” on the driver’s side lock
pillar. Gross axle weight rating
Front lb(kg)
Rear lb(kg)
*1: On spare tire carrier equipped models, the spare tire carrier adds 9.45 in (240
mm) to the overall length.
*2: SE and LE wide models
WHEELS AND TIRES
Technical and consumer information
9-11


04.3.9/R50-D/V5


NISSAN” in the “6. In case of emer-
gency” section of this manual.
Automatic transmissionTo tow a vehicle equipped with an automatic
transmission, an appropriate vehicle dollyMUST
be placed under the towed vehicle’s drive
wheels.Alwaysfollow the dolly manufacturer’s
recommendations when using their product.Manual transmissionAll mode 4WD (four wheel drive) models:
Never tow All mode 4WD models with any of the
wheels on the ground.
Part time four wheel drive models:

Move the transfer case shift lever to the 2H
position.

Move the transmission shift lever to the N
(Neutral) position.
Two wheel drive models:
Move the transmission shift lever to the N (Neu-
tral) position.

Always tow with the manual transmission in
Neutral.
After towing 500 miles, start and idle the
engine with the transmission in Neutral for
two minutes. Failure to idle the engine after
every 500 miles of towing may cause damage
to the transmission’s internal parts.

Always release the parking brake.
UNIFORM TIRE QUALITY GRADINGDOT (Department of Transportation) Quality
Grades: All passenger car tire must conform to
Federal Safety Requirements in addition to these
grades.
Quality grades can be found where applicable
on the tire sidewall between tread shoulder and
maximum section width. For example:
Treadwear 200 Traction AA Temperature ATreadwearTreadwear grade is a comparative rating based
on tire wear rate when tested under controlled
conditions on specified government test
courses. For example, a tire graded 150 would
wear one and a half (1-1/2) times as well on the
government course as a tire graded 100. How-
ever, relative tire performance depends on actual
driving conditions, and may vary significantly due
to variations in driving habits, service practices
and differences in road characteristics and cli-
mate.
Traction AA, A, B and CThe traction grades from highest to lowest are
AA, A, B, and C. Those grades represent the
tire’s ability to stop on wet pavement as mea-
sured under controlled conditions on specified
government test surfaces of asphalt and con-
crete. A tire marked C may have poor traction
performance.
WARNING
The traction grade assigned to your ve-
hicle tires is based on straight-ahead
braking traction tests, and does not in-
clude acceleration, cornering, hydro-
planing, or peak traction characteristics.Temperature A, B and CTemperature grades are A (the highest), B, and
C. They represent a tire’s resistance to heat
build-up, and its ability to dissipate heat when
tested under controlled conditions on a speci-
fied indoor laboratory test wheel. Sustained high
temperature can cause tire material to degener-
ate, reducing tire life. Excessive temperatures
can lead to sudden tire failure. Grade C corre-
sponds to a performance level which all passen-
ger car tires must meet under the Federal MotorTechnical and consumer information
9-23


04.3.9/R50-D/V5