2004 MITSUBISHI LANCER EVOLUTION VIII seats

REFERENCE MATERIAL – MAIN EQUIPMENT87
4WD
RSGSR
Equipment
5M/T6M/T
Seat finishFabriclll
Standard typell
Recaro seatr*1r*1l
SlideAdjustment
mechanism
Reclining
lll
Front
Seat
Headrest
Low back bench seat (fixed)
ll
High back bench seat (fixed)
Rear
Seat
Centre arm rest (with cup
holder)
l
2 ¥ 3point with
ELR
With pretensioner
(driver’s seat &
front passenger
seat)
Front
Adjustable
seatbelt anchor
SRS
airbags
Rear2 ¥ 3point with
ELR / ALR + 1 ¥ 2
point belt
lll
Driver’s seatlllSRS
airbags
Front passenger’s seatrrl
Accessories box (1 DIN)ll
Parcel box (with lid)l
Parcel
boxes
Coin box
Glove box
lll
Standard typell
Large typeWith lidl
Shift boot ringl
Front seatlllAshtray
Rear seatl
Floor
console
Cup holder (front seat)lll
Centre panel (unique type)ll
2 DIN typel
HeadliningClothlll
Moulded type (soft)Front door
trim
Door pocket (driver’s
seat, front passenger’s
seat)
Interior
Rear doorMoulded type (soft)
lll
4WD
RSGSR
Equipment
5M/T6M/T
Boot interior trim
Boot interior
floor carpetNeedle punch
l
¥ 1 (front passenger’s seat)llRetractable
assistance
straps
¥ 3 (front passenger’s seat,
rear seats)l
Driver’s seatlll
Front passenger’s seatrrl
Ticket holder (driver’s seat)lll
Sun
visors
Vanity mirror (with lid)l
Internal
mirrorDay / night switchable
Interior
Foot rests
lll
44B20LlllBattery
55B24Lrrr
Halogen (low and
high beam)ll
Discharge (low
beam)
Halogen (high
beam)
Fog lamps
(halogen)
rrl
Position lightslll
Automatic lightsl
Headlight levellingrrl
Extension (black)rrl
Rear combination
lights
(clear type *2)lll
External
lightsHeadlight
assembly
(Clear
type *2)
Extension (black)rrl
High mount stop
lightRear shelf mounting
(bulb type)
Front cabin lights (with map light)
lll
Rear cabin lightslll
Interior
lights
Boot interior light
Combination meterSpecial type
Electric type analogue
speedometer
Twin type trip meter
Tachometer
Water temperature
Meter
gauge
Fuel
lll
Fog lightsrrl
High beam
Turn signal and hazard lights
Equip
ment
Indicator
lights
ACD
lll
Note : *1: 4point seatbelt asymmetric type seat*2: Turn signal lamps coloured amber

FRONT SUSPENSION – STRUT ASSEMBLY33A3
CAUTION
(1) To compress the coil spring securely, ensure that the
special tool is extended as far as the spring will allow,
then fitted evenly to the coil spring.
(2)There is a danger of special tool damage, so do not use
an impact wrench.
2. Using the following special tools, release the selflocking nut.
• Special spanner (MB991367)
• Pin (MB991385)
CAUTION
There is a danger of the lock nut inside the strut piston rodworking loose, so when loosening the selflocking nut, do
not use an impact wrench.
Important note on assembly
Fitting selflocking nut
1. With the coil spring compressed with the special tool,
temporarily tighten the selflocking nut.
2. Match up strut assembly hole in lower spring seat, and hole in
upper spring seat.
Remarks
Using a lever to align the holes can make this job easier.
3. Match both tips of coil spring precisely with the slots on the
spring seats, and release the special tool.
4. Using the special tool, tighten the selflocking nut to the
specified torque.
Tightening tor
que: 60 ± 10N·m
CAUTION
There is a danger of the lock nut inside the strut piston rod
working loose, so when loosening the selflocking nut, do
not use an impact wrench.
A