2004 MITSUBISHI LANCER EVOLUTION VIII height

ENGINE (4G6) – BASE ENGINE (6 M/T)15
6. Camshaft
Output at high engine speeds has been improved by altering the cam profile of the intake camshaft, and optimizing the valve
timing.
Evolution VIII MREvolution VIII
Cam height mm35.9635.79
Evolution VIII MR Evolution VIII
T.D.C (top dead centre) T.D.C (top dead centre)
Intake valve open
Intake valve
closedExhaust
valve closed
Exhaust
valve openIntake valve open
Intake valve
closedExhaust
valve closed
Exhaust
valve open
B.D.C (Bottom dead centre) B.D.C (Bottom dead centre)

81REFERENCE MATERIAL – MAIN SPECIFICATIONS
SECTION 8
REFERENCE MATERIAL
CONTENTS
Main specifications.................................81
Detailed specifications ...........................84Main equipment ......................................86
Cold climate specifications ...................88
Main Specifications
These Main Specifications are based on submitted data, and may therefore differ from the actual equipment.
The
symbol indicates specifications which have changed from the previous model.
Vehicle name and modelMitsubishi GHCT9A
Chassis name and typeMitsubishi CT9A
ManufacturerMitsubishi Motor Corporation
CategoryNormal
UsePassenger
Body shapeSaloon
Engine type4G63
Capacity cc1997
GHCT9A
GHCT9AItem
SNDFZSJDFZSJGFZ
Classification No.È079, 080, 085, 086,
091, 092, 097, 098083, 084, 089,
090, 095, 096,
099~102105, 106, 109,
110, 113, 114,
117, 118119
Vehicle length mm4490
Vehicle width mm1770
Vehicle height mm1450
Wheelbase mm2625
Front15001515¨¨
Dimensions
Track mm
Rear15001515¨¨
WeightSee weight chart
Left50˚PerformanceMax.
angle ofstability
Right50˚
Wheel alignmentFront 2 drive – Rear 2 drive
Front
Other
Tyre
size
Rear
205/65R15 94H235/45ZR17¨¨
Note :
See Weight Chart for relationships between classification numbers and equipment.

02GENERAL MAIN SPECIFICATIONS
ITEMGHCT9A
SNDFZSJDFZSJGFZ
ClassOrdinary
UsePassenger
vehicle
Body
shapeSaloon
4490
1770
1450
Vehicle length mm
Vehicle width mmVehicle height mm
Distance between axles mm
2625
Front1515*1,
1500*21515*1Distance between
wheels mm
Rear1515*1,
1500*21515*1
Minimum ground clearance mm140
Length1880
Width1425
Interior dimensions
mm
Height1185
Front825
Dimensions
Body overhang mm
Rear875
Toein mm0±2
Camber *31º 00´ ±30´ or 2º 00´ ±30´
Castor3º 55´ ±30´
Front
wheels
King pin angle13º 45´
Toein mm3 ±2Rear
wheels
Camber1º 00´ ±30´
Driving
devices
Tyre size205/65R15 94H
235/45ZR17235/45ZR17
MAIN SPECIFICATIONS
Notes
1. *1 in the case of vehicles fitted with 17 inch tyres *2 in the case of vehicles fitted with 15 inch tyres
2.*3 it is possible to select from 3 types of camber. This is be set to 1˚ 00´ ±30´ when shipped from the factory.

MANUAL TRANSMISSION TROUBLESHOOTING2214
Code No.61 Stop lamp switch systemAssumed cause of concern
In cases where, at 15kph or over, the stop lamp switch stays
ON for 15 minutes or longer, code No.61 is output.• Brake pedal malfunction
•Stop lamp switch malfunction
• Harness, connector malfunction
•4WDECU malfunction
Remarks*1: Refer to ’005 Lancer Sedia Service Manual (No.1036K00)
Check height of brake pedal
(Refer to Group 35A – Vehicle Servicing)
*1
NG > Adjust
MUTII/III Service data
• No.56 Stop lamp switch
(1)Depress brake pedal
OK:ON
(2)Release brake pedal
OK:OFF
OK > Intermittent malfunction
Check connector:C118
NG > repair
Check stop lamp switch
(Refer to Group 35A – Brake pedal)
*1
NG > replace
Measurement at C118 stop lamp switch connector
• Undo connector, measure on harness side
•Voltage between 2 – earth
OK:battery voltage
Measurement at C37 4WDECU connector
• ECU terminal voltage measurement
•
Voltage between 38 earth
(1)Depress brake pedal
OK:battery voltage
(2)Release brake pedal
OK:1V or less
Connector check:C118, C22, C23, C37
NG > repair
Check harness between 4WDECU stop lamp
switch
• Check for broken or damaged output wire
NG > repair
Check harness between stop lamp switch – stop lamp.
• Check for broken or damaged output wireNG > repair
Connector check:C118, C31
NG > repair
Check harness between stop lamp switch – battery
•Check power supply wire to see if broken or
damaged
NG > repair
Connector check:C37
NG > repair
MUTII/III Service data
•No.56 Stop lamp switch
(1)Depress brake pedal
OK:ON
(2)Release brake pedal
OK:OFF
NG > replace 4WDECU
OK > Intermittent malfunction
NG
OK
OK
NG
OK
OK
OK
NG
OK
OK
OK
OK