GENERAL INFORMATION - DETAILS OF CHANGES0-3
Main circuit Name of circuit Page Details of change
J/C - p.3-2• Partial changes to circuit and
destination system names in J/C(1) —
(6)
-• With the introduction of manual air
conditioning, the circuit used by the
fusible link No.2 has been changed.
• Wastegate solenoid valve 2 added to
load of special fuse No.3.
• Rating of special fuse No.10 changed
from 15A to 20A.
Power supply - p.3-10• Partial changes to destination system
names.
• Earth No.13 added.
• Rating of special fuse No.10 changed
from 15A to 20A.
• Partial changes to circuit details, due
to removal of sunroof.
Engine control - p.3-16• Rating of special fuse No.10 changed
from 15A to 20A.
• Earth No.13 added.
• Some changes to circuit, due to
addition of wastegate solenoid valve
2 (B-32).
• Partial changes, due to removal of
DVD-MMCS
Lighting Interior lights, boot interior
light, ignition key cylinder
illumination light, door not
closed indicator light-• Change to terminal number in J/C(2)
(C-119) on line linking ETACS and
diagnosis connector. (No.1 " No.5)
Reversing lights -• Change to terminal number in J/C(2)
(C-119) on line linking reversing light
and rear combination light (LH).
(No.18 " No.19)Signal
Stop lights p.3-24• Spare connector (F-28) added, and
circuit partially changed.
Meters / Gauges -Meters
Remaining fuel warning
light, oil pressure warning
light, brake warning light,
seatbelt warning light-• Change to terminal number in J/C(1)
(C-07) on line inking J/B (general fuse
No.18) and combination meter. (No.4
" No.8)
• Change to terminal number in J/C(4)
(C-110) on line linking combination
meter and fuel gauge unit (sub).
(No.20 " No.21)
Door opening
controlElectric windows -• Change to terminal number in J/C(2)
(C-119) on line linking power window
main switch and diagnosis connector.
(No.12 " No.14)
Fully automatic air
conditioning-• Change to terminal number in J/C(1)
(C-07) on line linking J/B (general
fuse No. 18) and A/C-ECU. (No.6 "
No.4)
• Change to terminal number in J/C(5)
(C-06) on line linking A/C-ECU and
diagnosis connector. (No.8 " No.9)Air
conditioning
Manual air conditioning p.3-26• With the adoption of manual air
conditioning, a new circuit has been
installed.
Windscreen wipers and
washers-Safety and
visibility
Electric retractable remote
control door mirrors-• Change to terminal number in J/C(2)
(C-119) on line linking ETACS and
diagnosis connector. (No.1 " No.5)
Circuit diagrams
M3000004500157
GENERAL INFORMATION - LIST OF CIRCUIT DIAGRAMS0-5
Main circuit Name of Circuit Circuit Diagram
J/B -!
J/C -#
Central junction -#
Power supply -#
Start up -!
Ignition -!
Charging -!
Engine control -#
Coolant -!
Headlights (excluding discharge type )!
Headlight ( discharge type)!
Tail lights, side lights, licence plate lights, lighting monitor
warning buzzer!
Cabin lights, boot interior light, ignition key cylinder
illumination light, door not closed indicator light *2!
Fog lights!
Lighting
Headlight levelling system
!
Indicator lights, hazard warning lights!
Reversing lights *2!
Stop lights#
Signalling
Horn
!
Meters / Gauges *2!Meters
Remaining fuel warning light, oil pressure warning light,
brake warning light, seatbelt warning light *2
!
Electric windows *2!
Central door locking (vehicle not fitted with keyless entry)!
Door opening control
Central door locking (vehicle fitted with keyless entry)
!
Heater!
Fully automatic air conditioning!
Air conditioning
Manual air conditioning
#
List of Circuit Diagrams
M3000006000169
Notes:
1. This list of circuit diagrams indicates whether each circuit has been modified or added.
2. The “●” symbol indicates a circuit that has been modified or added. Diagrams for these circuits are included in
this supplement.
3. The “
” symbol indicates a circuit that is unchanged. Details of these circuits can be found in the existing
Electrical Wiring Diagram manual (’03-1 No.1036K77).
4. The “X” symbol indicates a circuit that is unrelated to the vehicle referred to in this manual.
5. The “*1” symbol marks circuits whose names have been changed the previous names.
6. The “*2” symbol marks circuits whose J/C terminal numbers have changed. For more information, please refer
to the “Details of Changes” table above.
