2004 MITSUBISHI LANCER EVOLUTION VIII engine oil

GENERAL INFORMATION - DETAILS OF CHANGES0-3
Main circuit Name of circuit Page Details of change
J/C - p.3-2• Partial changes to circuit and
destination system names in J/C(1) —
(6)
-• With the introduction of manual air
conditioning, the circuit used by the
fusible link No.2 has been changed.
• Wastegate solenoid valve 2 added to
load of special fuse No.3.
• Rating of special fuse No.10 changed
from 15A to 20A.
Power supply - p.3-10• Partial changes to destination system
names.
• Earth No.13 added.
• Rating of special fuse No.10 changed
from 15A to 20A.
• Partial changes to circuit details, due
to removal of sunroof.
Engine control - p.3-16• Rating of special fuse No.10 changed
from 15A to 20A.
• Earth No.13 added.
• Some changes to circuit, due to
addition of wastegate solenoid valve
2 (B-32).
• Partial changes, due to removal of
DVD-MMCS
Lighting Interior lights, boot interior
light, ignition key cylinder
illumination light, door not
closed indicator light-• Change to terminal number in J/C(2)
(C-119) on line linking ETACS and
diagnosis connector. (No.1 " No.5)
Reversing lights -• Change to terminal number in J/C(2)
(C-119) on line linking reversing light
and rear combination light (LH).
(No.18 " No.19)Signal
Stop lights p.3-24• Spare connector (F-28) added, and
circuit partially changed.
Meters / Gauges -Meters
Remaining fuel warning
light, oil pressure warning
light, brake warning light,
seatbelt warning light-• Change to terminal number in J/C(1)
(C-07) on line inking J/B (general fuse
No.18) and combination meter. (No.4
" No.8)
• Change to terminal number in J/C(4)
(C-110) on line linking combination
meter and fuel gauge unit (sub).
(No.20 " No.21)
Door opening
controlElectric windows -• Change to terminal number in J/C(2)
(C-119) on line linking power window
main switch and diagnosis connector.
(No.12 " No.14)
Fully automatic air
conditioning-• Change to terminal number in J/C(1)
(C-07) on line linking J/B (general
fuse No. 18) and A/C-ECU. (No.6 "
No.4)
• Change to terminal number in J/C(5)
(C-06) on line linking A/C-ECU and
diagnosis connector. (No.8 " No.9)Air
conditioning
Manual air conditioning p.3-26• With the adoption of manual air
conditioning, a new circuit has been
installed.
Windscreen wipers and
washers-Safety and
visibility
Electric retractable remote
control door mirrors-• Change to terminal number in J/C(2)
(C-119) on line linking ETACS and
diagnosis connector. (No.1 " No.5)
Circuit diagrams
M3000004500157

GENERAL INFORMATION - LIST OF CIRCUIT DIAGRAMS0-5
Main circuit Name of Circuit Circuit Diagram
J/B -!
J/C -#
Central junction -#
Power supply -#
Start up -!
Ignition -!
Charging -!
Engine control -#
Coolant -!
Headlights (excluding discharge type)!
Headlight (discharge type)!
Tail lights, side lights, licence plate lights, lighting monitor
warning buzzer!
Cabin lights, boot interior light, ignition key cylinder
illumination light, door not closed indicator light *2!
Fog lights!
Lighting
Headlight levelling system
!
Indicator lights, hazard warning lights!
Reversing lights *2!
Stop lights#
Signalling
Horn
!
Meters / Gauges *2!Meters
Remaining fuel warning light, oil pressure warning light,
brake warning light, seatbelt warning light *2
!
Electric windows *2!
Central door locking (vehicle not fitted with keyless entry)!
Door opening control
Central door locking (vehicle fitted with keyless entry)
!
Heater!
Fully automatic air conditioning!
Air conditioning
Manual air conditioning
#
List of Circuit Diagrams
M3000006000169
Notes:
1. This list of circuit diagrams indicates whether each circuit has been modified or added.
2. The “●” symbol indicates a circuit that has been modified or added. Diagrams for these circuits are included in
this supplement.
3. The “


” symbol indicates a circuit that is unchanged. Details of these circuits can be found in the existing
Electrical Wiring Diagram manual (’03-1 No.1036K77).
4. The “X” symbol indicates a circuit that is unrelated to the vehicle referred to in this manual.
5. The “*1” symbol marks circuits whose names have been changed the previous names.
6. The “*2” symbol marks circuits whose J/C terminal numbers have changed. For more information, please refer
to the “Details of Changes” table above.

WIRING DIAGRAMS - ENGINE TRANSMISSION1-2
ENGINE TRANSMISSION
M3010000400494
B-01 (1-black) Engine oil pressure switch
B-02 (1) Alternator
B-03 (4-grey) Alternator
B-04 (1) Starter
B-05 (1-black) Starter
B-06 (4-black) Throttle position sensorB-07 (2-black) Purge control solenoid valve
B-08 (7-black) Airflow sensor
B-12 (5-grey) Windscreen wiper motor
B-13X (1) Engine speed detection connector
B-14X (5) Starter relay
B-17X (4) Ignition coil relay
Connector
symbol -
B
-01
∫
-32
AC311230AB
Control harness
Battery harness

CIRCUIT DIAGRAMS - CENTRAL JUNCTION3-9
Fusible link (Relay box inside engine space)
Power supply circuitFuse No.Rated
current (A)ID
colourApplied loads
Battery / Alternator (fusible
link No. 6)320YellowO2sensor, secondary are
control solenoid valve, idle
speed control servo, ignition
coil 1, ignition coil 2, waste
gate solenoid valve 1, waste
gate solenoid valve 2, air
flow sensor, engine ECU,
engine control relay, cam
position sensor, crank angle
sensor, purge control
solenoid valve, fuel pressure
solenoid valve, radiator fan
control relay, register (for
injector)
1020YellowFuel pump relay 3, fuel pump
register, fuel pump & fuel
gauge unit (main)
Forward
direction of
vehicle