Page 127 of 434
126 Controls in detailInstrument clusterOutside temperature indicator
The outside temperature is displayed in
the right multifunction display
(page 22). For information on how to se-
lect the unit of the displayed temperature,
i.e. degrees Celsius (°C) or degrees Fahr-
enheit (°F), see “Selecting temperature
display mode” (
page 140).The temperature sensor is located in the
front bumper area. Due to its location, the
sensor can be affected by road or engine
heat during idling or slow driving. There-
fore, the accuracy of the displayed temper-
ature can only be verified by comparison to
a thermometer placed next the sensor, not
by comparison to external displays, e.g.
bank signs, etc.
When moving the vehicle into colder ambi-
ent temperatures (e.g. when leaving your
garage), you will notice a delay before the
lower temperature is displayed.
A delay also occurs when ambient temper-
atures rise. This prevents inaccurate tem-
perature indications caused by heat
radiated from the engine during idling or
slow driving.
Warning!
G
The outside temperature indicator is not de-
signed to serve as an Ice-Warning Device
and is therefore unsuitable for that purpose.
Indicated temperatures just above the freez-
ing point do not guarantee that the road sur-
face is free of ice. The road may still be icy,
especially in wooded areas or on bridges.
Page 211 of 434
210 Controls in detailDriving systemsParktronic* (Parking assist)
The Parktronic system is an electronic aid
designed to assist the driver during park-
ing maneuvers. It visually and audibly indi-
cates the relative distance between the
vehicle and an obstacle.
The Parktronic system is automatically ac-
tivated when you switch on the ignition
and release the parking brake. The Park-
tronic system deactivates at speeds above
11 mph (18 km/h). At lower speeds the
Parktronic system turns on again.The Parktronic system monitors the sur-
roundings of your vehicle with six sensors
in the front bumper and four sensors in the
rear bumper.
1Sensors in the front bumperWarning!
G
Parktronic is a supplemental system. It is
not intended to, nor does it replace, the
need for extreme care. The responsibility
during parking and other critical maneuvers
always rests with the driver.
Special attention must be paid to objects
with smooth surfaces or low silhouettes
(e.g. trailer couplings, painted posts, or road
curbs). Such objects may not be detected by
the system and can damage the vehicle.
The operational function of the Parktronic
system can be affected by dirty sensors, es-
pecially at times of snow and ice. See
“Cleaning the Parktronic* system sensors”
(page 277).
Interference caused by other ultrasonic sig-
nals (e.g. working jackhammers or the air
brakes of trucks) can cause the system to
send erratic indications, and should be tak-
en into consideration.
Warning!
G
Make sure that no persons or animals are in
the area in which you are maneuvering. Oth-
erwise you run the risk of causing injury.
Page 336 of 434
335 Practical hints
Replacing bulbs
Turn locking mechanism 2 clockwise.
Plug the connector onto the bulb.
Align headlamp cover and click into
place.
Replacing parking and standing lamp
bulbs
Switch off the lights.
Open the hood (
page 253).
Press ends of headlamp cover tab to-
gether and remove cover.
Pull out the bulb socket with the bulb.
Pull the bulb out of the bulb socket.
Insert a new bulb in the socket.
Reinstall the bulb socket.
Align headlamp cover and click into
place.Replacing side marker lamp
Switch off the lights.
Carefully slide lamp towards rear.
Remove front end first.
Twist bulb socket counterclockwise
and pull out.
Pull bulb out of the bulb socket.
Insert new bulb in socket.
Reinstall bulb socket, push in, and twist
clockwise.
To reinstall lamp, set rear end in
bumper and let front end snap into
place.
Replacing bulbs for rear lamps
Tail lamp assemblies
1Backup lamp
2Turn signal lamp
3Driver’s side: Rear fog lamp
Passenger’s side: Substitute lamp
Switch off the lights.
Open the trunk lid (
page 99).
Fold trim to side and remove.
Twist bulb socket counterclockwise
and pull out.
iHave the headlamp adjustment
checked regularly.
Page 369 of 434
368 Practical hintsTowing the vehicleInstalling towing eye bolt
Front of vehicle
1Cover on right side of front bumper.
To remove cover:
Press mark on cover 1 in direction of
arrow.
Lift cover1off to reveal threaded
hole for towing eye bolt.The towing eye bolt is supplied with the
tool kit (located in the storage compart-
ment under the trunk floor).
Screw towing eye bolt in to its stop and
tighten with lug wrench.
To reinstall cover:
Fit cover and snap into place.Rear of vehicle
2Cover on right side of rear bumper
To remove cover:
Pull cover 2 in the direction of arrow.
Fold cover 2 down to reveal threaded
hole for the towing eye bolt.
The towing eye bolt is supplied with the
tool kit (located in the storage compart-
ment under the trunk floor).
Screw towing eye bolt in to its stop and
tighten with lug wrench.
To reinstall cover:
Fit cover 2 and snap into place.
