Page 333 of 435
332 Practical hintsWhat to do if …?Display symbol
Display message
Possible cause
Possible solution
.
STANDING LIGHT, L
CHECK LAMP!
SUBSTITUTE LAMP ON!
The left standing lamp is malfunctioning.
A back-up bulb is being used.
Replace the bulb as soon as possible.
STANDING LIGHT, R
CHECK LAMP!
SUBSTITUTE LAMP ON!
The right standing signal lamp is malfunc-
tioning. A back-up bulb is being used.
Replace the bulb as soon as possible.
TAIL LIGHT, L
CHECK LAMP!
SUBSTITUTE LAMP ON!
The left tail lamp is malfunctioning. A
back-up bulb is being used.
Replace the bulb as soon as possible.
TAIL LIGHT, R
CHECK LAMP!
SUBSTITUTE LAMP ON!
The right tail lamp is malfunctioning. A
back-up bulb is being used.
Replace the bulb as soon as possible.
SWITCH OFF LIGHTS!
Lamps have been turned on although the
SmartKey in the ignition is in position 0.
Turn off the headlamps.
TURN SIGNAL F, L
CHECK LAMP!
SUBSTITUTE LAMP ON!
The left front turn signal lamp is malfunc-
tioning. A back-up bulb is being used.
Replace the bulb as soon as possible.
TURN SIGNAL F, R
CHECK LAMP!
SUBSTITUTE LAMP ON!
The right front turn signal lamp is mal-
functioning. A back-up bulb is being used.
Replace the bulb as soon as possible.
Page 334 of 435
333 Practical hints
What to do if …?
Display symbol
Display message
Possible cause
Possible solution
.
TURN SIGNAL, L
CHECK LAMP!
SUBSTITUTE LAMP ON!
The left rear turn signal lamp is malfunc-
tioning. A back-up bulb is being used.
Replace the bulb as soon as possible.
TURN SIGNAL, R
CHECK LAMP!
SUBSTITUTE LAMP ON!
The right rear turn signal lamp is malfunc-
tioning. A back-up bulb is being used.
Replace the bulb as soon as possible.
TURN SIG. MIRROR, L
CHECK LAMP!
The left turn signal in the side mirror is
malfunctioning. This message will only ap-
pear if all light emitting diodes have
stopped working.
Visit an authorized Mercedes-Benz Cen-
ter as soon as possible.
TURN SIG. MIRROR, R
CHECK LAMP!
The right turn signal in the side mirror is
malfunctioning. This message will only ap-
pear if all light emitting diodes have
stopped working.
Visit an authorized Mercedes-Benz Cen-
ter as soon as possible.
<
SEAT BELT SYSTEM
VISIT WORKSHOP!
The seat belt system is malfunctioning.
Visit an authorized Mercedes-Benz
Center as soon as possible.
K
CLOSE
SUNROOF!
You have opened the driver’s door with
the SmartKey removed from the starter
switch and the sliding/pop up roof open.
Close the sliding/pop-up roof
(page 199).
J
CLOSE
SUNROOF!
You have opened the driver’s door with
the SmartKey removed from the starter
switch and the sliding/pop up roof open.
Close the sliding/pop-up roof
(page 199).
Page 352 of 435
351 Practical hints
Unlocking/locking in an emergency
SmartKey with KEYLESS-GO*
1Battery
2Tilt battery up
3Mechanical keyReplacement battery: Lithium, type
CR 2025 or equivalent.
Remove mechanical key (
page 348).
Insert the mechanical key in side open-
ing and push gray slide.
The battery compartment is unlatched.
Pull the battery compartment out of the
SmartKey housing.
Using mechanical key3, apply pres-
sure to position2.
Battery1 tilts up slightly.
Pull out battery1 in direction of ar-
row.
Using a lint-free cloth, insert new bat-
tery with the plus (+) side facing up.
Return battery compartment into hous-
ing until it locks into place.
Fuel filler flap
In case the central locking system does
not release the fuel filler flap, you can it
manually.
1Release knob
Open the trunk.
Remove the trim inside the trunk on the
right-hand side.
Pull release knob1 in the direction of
arrow.
The fuel filler flap can be opened.
iThe required replacement battery is
available at any authorized
Mercedes-Benz Center.
Page 353 of 435
352 Practical hintsOpening/closing in an emergency
Opening/closing in an emergencySliding/pop-up roof
You can open or close the sliding/pop-up
roof manually should an electrical malfunc-
tion occur.
The driving mechanism for the slid-
ing/pop-up roof is located behind the lens
of the interior overhead light.
1Lens
Pry off lens1 using a flat blade srew-
driver (
page 344).
Turn the SmartKey in the starter switch
to position1 or2.
Remove the crank from the operator’s
manual pouch.
2Crank
Insert crank2 through hole.
Turn crank2 clockwise to:
close slide roof
raise roof at the rear
Turn crank2 counterclockwise to:
open slide roof
lower roof at the rear
The sliding/pop-up roof must be resyn-
chronized after being operated manually
(
page 202).
Page 354 of 435
353 Practical hints
Replacing bulbs
Replacing bulbs
Safe vehicle operation depends on proper
exterior lighting and signaling. It is there-
fore essential that all bulbs and lamp as-
semblies are in good working order at all
times.
Correct headlamp adjustment is extremely
important. Have headlamps checked and
readjusted at regular intervals and when a
bulb has been replaced. See an authorized
Mercedes-Benz Center for headlamp ad-
justment.
Bulbs Front lamps
iBackup bulbs will be brought into use
when the following lamps malfunction:
Turn signal lamps
Brake lamps
Parking lamps
Tail lamps
Lamp
Type
1
Additional turn sig-
nal lamps
LED
2
Low beam
1
1Vehicles with Bi-Xenon headlamps*: Low beam
and high beam use the same D2S-35W lamp. Do
not replace the Bi-Xenon bulbs yourself. See an au-
thorized Mercedes-Benz Center.
H7-55 W
Bi -Xenon*
D2S-35 W
3
Turn signal lamp
2357 A
4
Fog lamp
H7-55 W
5
Parking and stand-
ing lamp
W5W
6
Side marker lamp
W5W
7
High beam
H7-55 W
Page 355 of 435
354 Practical hintsReplacing bulbsRear lamps Notes on bulb replacement
Only use 12 volt bulbs of the same type
and with the specified watt rating.
Switch lights off before changing a bulb
to prevent short circuits.
Always use a clean lint-free cloth when
handling bulbs.
Your hands should be dry and free of oil
and grease.
If the newly installed bulb does not
come on, visit an authorized
Mercedes-Benz Center.
Have the LEDs and bulbs for the follow-
ing lamps replaced by an authorized
Mercedes-Benz Center.
Additional turn signal lamps in the
exterior rear view mirrors
High mounted brake lamp
Bi-Xenon lamps*
Front fog lamps
Lamp
Type
8
Brake lamp
LED
9
Turn signal lamp
PY 21 W
a
Tail and standing
lamp, side marker
P 21/4 W
b
Backup lamp
P21W
c
License plate lamps
C5W
d
Tail lamp, Rear fog
lamp
P 21/4 W
e
High mounted brake
lamp
LED
Warning!
G
Keep bulbs out of reach of children.
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Halogen lamps contain pressurized gas. A
bulb can explode if you:
touch or move it when hot
drop the bulb
scratch the bulb
Wear eye and hand protection.
Because of high voltage in Bi-Xenon lamps,
it is dangerous to replace the bulb or repair
the lamp and its components. We recom-
mend that you have such work done by a
qualified technician.
Page 356 of 435
355 Practical hints
Replacing bulbs
Replacing bulbs for front lamps
1Headlamp cover for fog lamp
2Headlamp cover for high beam halogen
headlamp bulb, parking and standing
lamp
3Headlamp cover for Bi-Xenon* (low and
high beam) or halogen (low beam)
headlamp bulb4Bulb socket for fog lamp
5Bulb socket for parking and standing
lamp
6Electrical connector for high beam
halogen headlamp bulb
7Electrical connector for low beam
headlamp bulb
8Bulb socket for turn signal lampReplacing low beam bulbs
Bi-Xenon* headlamp
Halogen headlamp
Switch off the lights.
Open the hood (
page 272).
Press the tab on cover3 and remove
cover.
Pull connector7 off of the lamp.
Release the retaining springs and take
out the bulb.Warning!
G
Do not remove the cover for the Bi-Xenon
headlamp. Because of high voltage in Xenon
lamps, it is dangerous to replace the bulb or
repair the lamp and its components. We rec-
ommend that you have such work done by a
qualified technician.
Page 357 of 435
356 Practical hintsReplacing bulbs
Insert the new bulb in the socket so
that the base is in the recess on the
lower left.
Attach the retaining springs.
Insert connector7 into the bulb.
Press cover3 onto the housing until
the tab engages.Replacing halogen high beam bulbs
Switch off the lights.
Open the hood (
page 272).
Press the tab on cover2 and remove
cover.
Pull connector 6 off of the bulb.
Apply pressure on the bulb contacts
from above until the bulb releases from
the retaining springs.
Remove bulb.
Insert the new bulb in the socket with
the marking facing upward.
Press the bulb upward on the contacts
until it engages in the retaining springs.
Insert connector6 onto the bulb.
Press cover2 onto the housing until
the tab engages.Front turn signal lamp bulb
Switch off the lights.
Open the hood (
page 272).
Twist bulb socket8 counterclockwise
and pull out.
Gently push bulb into socket, turn
counterclockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinstall bulb socket in lamp and twist
clockwise until it engages.
