2004 MERCEDES-BENZ E500 Features

261 Controls in detail
Useful features
Rolling code programming
To train a garage door opener (or other roll-
ing code devices) with the rolling code fea-
ture, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:
Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
m a y v a r y b y g a r a g e d o o r o p e n e r b r a n d .
Depending on manufacturer, the “train-
ing” button may also be referred to as
“learn”or “smart” button. If there is dif-
ficulty locating the transmitting button,
refer to the garage door opener opera-
tor’s manual. Step 9:

Press “training” button on the garage
door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the follow-
ing step.
Step 10:

Firmly press, hold for two seconds and
release the programmed integrated
signal transmitter button (1, 2
or3).
Step 11:

Press, hold for two seconds and re-
lease same button a second time to
complete the training process.
Some garage door openers (or other rolling
code equipped devices) may require you to
perform this procedure a third time to
complete the training.Step 12:

Confirm the garage door operation by
pressing the programmed integrated
signal transmitter button (1, 2
or3).
Step 13:

To program the remaining two buttons,
repeat the steps above starting with
step 3.

262 Controls in detailUseful featuresGate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the inte-
grated signal transmitter to pick up the sig-
nal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having dif-
ficulties programming a gate operator (re-
gardless of where you live) by using the
programming procedures, replace step 4
with the following:Step 4:

Continue to press and hold the inte-
grated signal transmitter button (1,
2 or3) while you press and re-press
(“cycle”) your hand-held remote con-
trol transmitter6 every two seconds
until the frequency signal has been
learned. Upon successful training, the
indicator lamp4 will flash slowly and
then rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete. Operation of integrated remote control

Switch on ignition.

Select and press the appropriate inte-
grated signal transmitter button (1,
2 or3) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.

263 Controls in detail
Useful features
Erasing the integrated remote control
memory
Switch on ignition.

Simultaneously hold down the signal
transmitter buttons1 and 3, for ap-
proximately 20 seconds, until the indi-
cator lamp4 blinks rapidly. Do not
hold for longer than 30 seconds.
The codes of all three channels are
erased.Reprogramming a single integrated
signal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Press and hold the desired signal trans-
mitter button (1, 2 or3). Do not re-
lease the button.

The indicator lamp will begin to flash af-
ter 20 seconds. Without releasing the
integrated signal transmitter button,
proceed with programming starting
with step 3.
iIf you sell your vehicle, erase the codes
of all three channels.

439 Index
U
Units
Setting speedometer units 141
Setting temperature units 141
Setting tire inflation pressure
units 143
Unlocking 30, 88, 353
Centrally from inside 107
Driver’s door in an emergency 353
Fuel filler flap 278
Global 89
Global with KEYLESS-GO* 94
Selective settings 89, 94
Trunk in an emergency 354
Trunk lid with KEYLESS-GO* 95
Trunk lid with SmartKey 90
Vehicle in an emergency 257
With KEYLESS-GO* 32
With the SmartKey 30
Upgrade signals
Tele Aid* 256
Uphill driving
Cruise control 212
Upshifting 159Useful features 242
Ashtrays 246
Cigarette lighter 247
Garage door opener 258
Heated steering wheel* 248
Tele Aid* 250
Telephone* 249
V
Vehicle
Individual settings 138, 140
Locking in an emergency 354
Lowering 374
Towing 381
Unlocking in an emergency 353
Vehicle care
Cup holder 307
Distronic* system sensor cover 305
Engine cleaning 304
Gear selector lever 307
Hard plastic trim items 307
Leather upholstery 308
Light alloy wheels 307
Ornamental moldings 304
Paintwork 303
Parktronic* system sensor 305Plastic and rubber parts 308
Power washer 303
Seat belts 307
Steering wheel 307
Tar stains 303
Vehicle washing 304
Window cleaning 306
Wood trims 308
Vehicle level
Changing 228
Setting 228
Automatic 228
Manual 228
Vehicle level control system*
Airmatic DC* 226
Vehicle tool kit 352
Alignment bolt 352
Fuse extractor 352
Hex-socket wrench 352
Open-end wrench 352
Screwdriver 352
Spare fuses 352
Towing eye bolt 352
Universal pliers 352
Vehicle jack 350
Wheel wrench 352