Page 315 of 464
315 Practical hints
What to do if …?
Problem
Possible cause
Suggested solution
•
The red coolant warning lamp
comes on when the engine is
running.
There is insufficient coolant in the reservoir.
Add coolant to prevent engine from
overheating (
page 292).
If this warning lamp comes on frequently,
there is a leak in the cooling system.
Have the cooling system checked.
If the coolant level is correct, the electric ra-
diator fan may be broken.
If the coolant temperature is below
257 °F (125 °C), you can continue
driving to the nearest authorized
Mercedes-Benz Center.
Avoid high engine loads (e.g. driving
uphill) and stop-and-go driving.
•
The red coolant warning lamp
comes on while driving and you
hear a warning sound.
The coolant temperature has exceeded
257 °F (125 °C).
Stop as soon as possible and allow
the engine and coolant to cool down.
Warning!
G
Driving when your engine is badly overheat-
ed can cause some fluids which may have
leaked into the engine compartment to
catch fire. You could be seriously burned.
Steam from an overheated engine can cause
serious burns and can occur just by opening
the hood. Stay away from the engine if you
see or hear steam coming from it.
Turn off the engine, get out of the vehicle
and do not stand near the vehicle until the
engine has cooled down.
ProCarManuals.com
Page 329 of 464
329 Practical hints
What to do if …?
During severe operating conditions and
stop-and-go city traffic, the coolant tem-
perature may rise close to 248°F (120°C).
Display symbol
Display message
Possible cause
Possible solution
Ï
Coolant
Stop, engine off!
The coolant is too hot.
Stop the vehicle and turn off the en-
gine.
Only start the engine again after the
message disappears. You could other-
wise damage the engine.
Warning!
G
Driving when your engine is badly overheat-
ed can cause some fluids which may have
leaked into the engine compartment to
catch fire. You could be seriously burned.
Steam from an overheated engine can cause
serious burns and can occur just by opening
the hood. Stay away from the engine if you
see or hear steam coming from it.
Turn off the engine, get out of the vehicle
and do not stand near the vehicle until the
engine has cooled down.
!The engine should not be operated with
the coolant temperature above 248°F
(120°C). Doing so may cause serious
engine damage which is not covered by
the Mercedes-Benz Limited Warranty.
ProCarManuals.com
Page 334 of 464
334 Practical hintsWhat to do if …?Display symbol
Display message
Possible cause
Possible solution
A
Reserve fuel
The fuel level has dropped below the re-
serve mark.
Refuel at the next gas station
(page 284).
Y
Hood open!
You are driving with the hood open.
Close the hood (
page 288).
I
Remove key
You have forgotten to remove the
SmartKey.
Remove the SmartKey from the start-
er switch.
Replace key!
No additional code available for SmartKey
or SmartKey with KEYLESS-GO*
Visit an authorized Mercedes-Benz
Center as soon as possible.
Key
Check battery!
The SmartKey with KEYLESS-GO* batter-
ies are discharged.
Change the batteries (
page 350).
Key
not recognized!
The SmartKey with KEYLESS-GO* is not
recognized while the engine is running be-
cause
the SmartKey is not in the vehicle
there is strong radio-frequency inter-
ference
Stop the vehicle as soon as it is safe to
do so.
Search for the SmartKey.
Otherwise the vehicle cannot be centrally
locked nor can the engine be started
again after the engine has been stopped.
The SmartKey with KEYLESS-GO* is mo-
mentarily not recognized.
Change the position of the SmartKey
in the vehicle.
Operate the vehicle with the SmartKey
in the starter switch if necessary.
Keyless Go
Check system
The KEYLESS-GO* system is malfunction-
ing.
Visit an authorized Mercedes-Benz
Center as soon as possible.
ProCarManuals.com
Page 375 of 464
375 Practical hints
Replacing bulbs
Low beam and high beam bulb
Switch off the lights.
Open the hood (
page 287).
Turn housing cover1 or 2 counter-
clockwise and remove.
Turn bulb holder 4 or 5 with the bulb
counterclockwise and remove.
Press the bulb backwards and turn
counterclockwise out of the bulb hold-
er.
Press the new bulb into the holder and
twist it clockwise.
Place the bulb holder back into the
lamp and turn it clockwise.
Place the corresponding housing cov-
ers back on and turn them clockwise.Front turn signal lamp bulb
Switch off the lights.
Open the hood (
page 287).
Twist bulb socket3 counterclockwise
and pull out.
Push bulb into socket, turn counter-
clockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinsert bulb socket in lamp and twist
clockwise.Parking and standing lamp bulb
Switch off the lights.
Open the hood (
page 287).
Turn housing cover2 counterclock-
wise and remove.
Pull out the bulb socket with the bulb.
Pull the bulb out of the bulb socket.
Insert a new bulb in the socket.
Reinstall the bulb socket.
Align housing cover and click into
place.
ProCarManuals.com
Page 376 of 464
376 Practical hintsReplacing bulbsFront lamps Bi-Xenon*-type
1Bulb socket for turn signal lamp
2Housing cover for high beam flasher
lamp
3Housing cover for Bi-Xenon* lamp4High beam flasher bulb
5Parking and standing lampHigh beam bulb for high beam flasher
Switch off the lights.
Open the hood (
page 287).
Turn housing cover2 counterclock-
wise and remove.
Turn bulb holder 4 with the bulb coun-
terclockwise and remove.
Press the bulb backwards and turn
counterclockwise out of the bulb hold-
er.
Press the new bulb into the holder and
twist it clockwise.
Place the bulb holder back into the
lamp and turn it clockwise.
Place the housing cover 2 back on
and turn them clockwise.
Warning!
G
Do not remove the cover
3
for the Bi-Xe-
non* headlamp. Because of high voltage in
xenon lamps, it is dangerous to replace the
bulb or repair the lamp and its components.
We recommend that you have such work
done by a qualified technician.
ProCarManuals.com
Page 377 of 464
377 Practical hints
Replacing bulbs
Front turn signal lamp bulb
Switch off the lights.
Open the hood (
page 287).
Twist bulb socket1 counterclockwise
and pull out.
Push bulb into socket, turn counter-
clockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinsert bulb socket in lamp and twist
clockwise.Parking and standing lamp bulb
Switch off the lights.
Open the hood (
page 287).
Turn housing cover2 counterclock-
wise and remove.
Pull out the bulb socket with the bulb.
Pull the bulb out of the bulb socket.
Insert a new bulb in the socket.
Reinstall the bulb socket.
Align housing cover and click into
place.
Side marker lamp bulb
Switch off the lights.
Carefully slide lamp towards rear.
Remove front end first.
Twist bulb socket counterclockwise
and pull out.
Pull bulb out of the bulb socket.
Insert new bulb in socket.
Reinstall bulb socket, push in and twist
clockwise.
To reinstall lamp, set rear end in
bumper and let front end snap into
place.
ProCarManuals.com
Page 379 of 464
379 Practical hints
Replacing wiper blades
Replacing wiper blades
Removing wiper blades
Fold the wiper arm forward.
1Lock
2Unlock
Pull the tab in direction of arrow2 and
remove windshield wiper.
Installing wiper blades
Slide the wiper blade into the cutout on
the wiper arm.
Slide the tab back in direction of
arrow1 until it audibly engages.
Fold the wiper arm backward to rest on
the windshield. Make sure you hold on
to the wiper when folding the wiper arm
back.
Warning!
G
For safety reasons, remove SmartKey from
starter switch before replacing a wiper
blade. Otherwise the motor could suddenly
turn on and cause injury.
!Never open the hood when the wiper
arms are folded forward.
Hold on to the wiper when folding the
wiper arm back. If released, the force
of the impact from the tensioning
spring could crack the windshield.
Do not allow the wiper arms to contact
the windshield glass without a wiper
blade inserted.
Make certain that the wiper blades are
properly installed. Improperly installed
wiper blades may cause windshield
damage.
For your convenience, we recommend
that you have this work carried out by
an authorized Mercedes-Benz Center.
ProCarManuals.com
Page 386 of 464
386 Practical hintsBatteryDisconnecting the battery
1Negative terminal
2Positive terminal cover
Depress parking brake firmly or move
gear selector lever to positionP.
Turn off all electrical consumers.
Remove SmartKey from starter switch.
Vehicles with KEYLESS-GO*:
Press the start / stop button until
the engine shuts off.
Open the driver’s door.
Open the hood (
page 287).
Remove the filter box.
Disconnect the battery negative lead.
Remove cover2 from the positive ter-
minal.
Disconnect the battery positive lead.
Removing the battery
Remove the screw securing the bat-
tery.
Remove the battery support and brack-
et.
Take out the battery.
Charging and reinstalling battery
Charge battery in accordance with the
instructions of the battery charger
manufacturer.
Reinstall the charged battery. Follow
the previously described steps in re-
verse order.
Warning!
G
With a disconnected battery
you will no longer be able to turn the
SmartKey in the starter switch and
pressing the KEYLESS-GO* start/stop
button on the gear selector lever will
have no effect
the gear selector lever will remain
locked in position
P
Warning!
G
Never charge a battery while still installed in
the vehicle. Gases may escape during charg-
ing and cause explosions that may result in
paint damage, corrosion or personal injury.
ProCarManuals.com
